SMALL BUSINESS PARTICIPATION AND DVBE PARTICIPATION REPORTING REQUIREMENTS a. If for this Contract Contractor made a commitment to achieve small business participation, then Contractor must within 60 days of receiving final payment under this Contract (or within such other time period as may be specified elsewhere in this Contract) report to the awarding department the actual percentage of small business participation that was achieved. (Govt. Code § 14841.)
Small Business Preference Commitment This section is applicable if Contractor received a small business preference in connection with this Agreement. Contractor’s failure to meet the small business commitment set forth in its bid or proposal constitutes a breach of this Agreement. Contractor must within sixty (60) days of receiving final payment under this Agreement report to the JBE the actual percentage of small/micro business participation that was achieved. If Contractor is a nonprofit veteran service agency (“NVSA”), Contractor must employ veterans receiving services from the NVSA for not less than 75 percent of the person-hours of direct labor required for the production of goods and the provision of services performed pursuant to this Agreement.
STAFF COMMITMENT 23. If this Settlement Agreement is accepted by the Hearing Panel, Staff will not initiate any proceeding under the By-laws of the MFDA against the Respondent in respect of the facts set out in Part IV and the contraventions described in Part V of this Settlement Agreement, subject to the provisions of Part IX below. Nothing in this Settlement Agreement precludes Staff from investigating or initiating proceedings in respect of any facts and contraventions that are not set out in Parts IV and V of this Settlement Agreement or in respect of conduct that occurred outside the specified date ranges of the facts and contraventions set out in Parts IV and V, whether known or unknown at the time of settlement. Furthermore, nothing in this Settlement Agreement shall relieve the Respondent from fulfilling any continuing regulatory obligations.
Program Participation By participating in the CRF Program, Grantee agrees to:
COOPERATIVE PURCHASING PROGRAM PARTICIPATION Arkansas' Purchasing Law provides that local public procurement units (counties, municipalities, school districts, certain nonprofit corporations, etc.) may participate in state purchasing contracts. The contractor therefore agrees to sell to Cooperative Purchasing Program participants at the option of the program participants. Unless otherwise stated, all standard and special terms and conditions listed within the contract must be equally applied to such participants.
PARTICIPATION, CONTRACT ACCESS, AND PARTICIPATING ENTITY REQUIREMENTS A. PARTICIPATION. Sourcewell’s cooperative contracts are available and open to public and nonprofit entities across the United States and Canada; such as federal, state/province, municipal, K-12 and higher education, tribal government, and other public entities. The benefits of this Contract should be available to all Participating Entities that can legally access the Equipment, Products, or Services under this Contract. A Participating Entity’s authority to access this Contract is determined through its cooperative purchasing, interlocal, or joint powers laws. Any entity accessing benefits of this Contract will be considered a Service Member of Sourcewell during such time of access. Supplier understands that a Participating Entity’s use of this Contract is at the Participating Entity’s sole convenience and Participating Entities reserve the right to obtain like Equipment, Products, or Services from any other source. Supplier is responsible for familiarizing its sales and service forces with Sourcewell contract use eligibility requirements and documentation and will encourage potential participating entities to join Sourcewell. Sourcewell reserves the right to add and remove Participating Entities to its roster during the term of this Contract.
Post-Award Small Business Program Re Representation If applicable, The Contractor shall report timely and accurately their small business program re-representation and update XXX.xxx.
DVBE Commitment This section is applicable if Contractor received a disabled veteran business enterprise (“DVBE”) incentive in connection with this Agreement. Contractor’s failure to meet the DVBE commitment set forth in its bid or proposal constitutes a breach of the Agreement. If Contractor used DVBE subcontractor(s) in connection with this Agreement: (i) Contractor must use the DVBE subcontractors identified in its bid or proposal, unless the JBE approves in writing replacement by another DVBE subcontractor in accordance with the terms of this Agreement; and (ii) Contractor must complete and return to the JBE a post-contract certification form promptly upon completion of the awarded contract, and by no later than the date of submission of Contractor’s final invoice to the JBE. (The post-contract certification form is located at: xxxxx://xxx.xxxxxx.xx.xxx/documents/JBCM-Post- Contract-Certification-Form.docx) If the Contractor fails to do so, the JBE will withhold $10,000 from the final payment, or withhold the full payment if it is less than $10,000, until the Contractor submits a complete and accurate post-contract certification form. The JBE shall allow the Contractor to cure the deficiency after written notice of the Contractor’s failure to complete and submit an accurate post- contract certification form. Notwithstanding the foregoing and any other law, if after at least 15 calendar days, but no more than 30 calendar days, from the date of the written notice the Contractor refuses to comply with these certification requirements, the JBE shall permanently deduct $10,000 from the final payment, or the full payment if less than $10,000. The post-contract certification form shall include: (1) the total amount of money Contractor received under the Agreement, (2) the total amount of money and the percentage of work that Contractor committed to provide to each DVBE subcontractor; (3) the name and address of each DVBE subcontractor to which Contractor subcontracted work in connection with the Agreement; (4) the amount of money each DVBE subcontractor actually received from Contractor in connection with the Agreement, and the corresponding percentage this payment comprises of the total amount of money Contractor received under the Agreement; and (5) that all payments under the Agreement have been made to the applicable DVBE subcontractors. Upon request by the JBE, Contractor shall provide proof of payment for the work. A person or entity that knowingly provides false information shall be subject to a civil penalty for each violation. Contractor will comply with all rules, regulations, ordinances and statutes that govern the DVBE program, including, without limitation, Military and Veterans Code section 999.5.
OFFSET CREDIT/COOPERATION This Contract has been entered into in direct support of LOCKHEED XXXXXX'x international offset programs. All offset benefit credits resulting from this Contract are the sole property of LOCKHEED XXXXXX to be applied to the offset program of its choice. SELLER shall assist LOCKHEED XXXXXX in securing appropriate offset credits from the respective country government authorities.
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
