Common use of Front Clause in Contracts

Front. The front shall have a facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide finished, running full length of the shirt and shall be topstitched 1/4" from both edges. The center front shall contain six vertical buttonholes placed 3/4" from edge. First at neck, second2-1/2" down, balance 3-1/2" apart. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.

Front. The front fronts shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn turn-under of material. The left right front shall also have a lined box pleat 1-1/2" wide finished, running full length of the shirt and shall be topstitched 1/4" from both edges. The center front shall contain six vertical buttonholes placed 3/4" from edge. First , first at neck, second2-1/2second 21/2" down, balance 3-1/2" apart. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.

Front. The front shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide finished, running full length extending from the collar stand to bottom of shirt and be made of the same material as shirt and shall be topstitched 1/4fabric with two rows of stitching 7/8" from both edgesapart. The center front shall contain six vertical buttonholes placed 3/4" from edge. First at neck, second2-1/2" down, balance edge and 3-1/2" apart. The button stand, 7/8" wide, shall be self-lined and placed on left side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the button stand and shall correspond to the buttonholes on the center facing. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.

Front. The left front shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide finished, running full length extending from the collar stand to bottom of shirt and be made of the same material as shirt and shall be topstitched 1/4fabric with two rows of stitching 7/8" from both edgesapart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge. First at neck, second2-1/2" down, balance edge and 3-1/2" apart. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplinmatching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/41/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. Flaps to The top stitching and the setting of the flaps shall be secured to front of shirt done with two rows of stitching approximately 1/4" above stitching. Flaps to have vertical stitched-in creases through the center on the top of pocketply only. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside outside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yokeshirt. To be 2-1/4” and have two small (horizontal) buttonholes, metal eyelets 1-1/4" apart with the bottom buttonhole 1-1/2of the patch 3/4" above top of left flap.

Front. The front shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide finished, running full length extending from the collar stand to bottom of shirt and be made of the same material as shirt and shall be topstitched 1/4fabric with two rows of stitching 7/8" from both edgesapart. The center front shall contain six (6) vertical buttonholes placed 3/4" from edge. First at neck, second2-1/2" down, balance edge and 3-1/2" apart. The button stand, 7/8" wide, shall be self-lined and placed on right side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the button stand and shall correspond to the buttonholes on the center facing. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/411/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.

Front. The Each front shall have a facing 33½" in width extending from the neckline to the bottom of shirt provided by a turn under of material. The left right front shall also have a lined box pleat 1-1/2" wide finished, running full length of the shirt and shall be topstitched 1/4" from both edges. The center front Zipper: A 14" nylon zipper shall contain six vertical buttonholes placed 3/4" from edge. First at neck, second2-be sewn to the fronts and shall be positioned 1- 1/2" downbelow the first front button and shall replace the 2nd, balance 3-1/2" apart3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplinmatching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/41/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. Flaps to The top stitching and the setting of the flaps shall be secured to front of shirt done with two rows of stitching approximately 1/4" above stitching. Flaps to have vertical stitched-in creases through the center on the top of pocketply only. The left flap to have a an invisible pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside outside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yokeshirt. To be 2-1/4” and have two small (horizontal) buttonholes, metal eyelets 1-1/4" apart with the bottom buttonhole 1-1/2of the patch 3/4" above top of left flap.

Front. The front shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide finished, running full length extending from the collar stand to bottom of shirt and be made of the same material as shirt and shall be topstitched 1/4fabric with two rows of stitching 7/8" from both edgesapart. The center front shall contain six vertical buttonholes placed 3/4" from edge. First at neck, second2-1/2" down, balance edge and 3-1/2" apart. The button stand, 7/8" wide, shall be self-lined and placed on left side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the button stand and shall correspond to the buttonholes on the center facing. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered mitred corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.