FULL BENCH CONSTRUCTION. Where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width except as construction staked or designed.
FULL BENCH CONSTRUCTION. Where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width except as construction staked or designed. SUBSECTION DITCH CONSTRUCTION 4-21 TURNOUTS Purchaser shall construct turnouts as designated on the TURN OUT AND TURNAROUND LIST. Locations may be adjusted to fit the final subgrade alignment and sight distances. Locations changes are subject to written approval by the Contract Administrator. Minimum dimensions are shown on the TYPICAL SECTION SHEET.
FULL BENCH CONSTRUCTION. Where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width except as construction staked or designed. SUBSECTION DITCH CONSTRUCTION
FULL BENCH CONSTRUCTION. Where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width except as construction staked or designed. If designated, Purchaser shall end haul waste material to the location specified in Clause 4-37 WASTE AREA LOCATION. SUBSECTION INTERSECTIONS, TURNOUTS AND TURNAROUNDS 4-21 TURNOUTS Turnouts shall be intervisible with maximum of 1,000 feet between turnouts unless shown otherwise on drawings. Locations shall be adjusted to fit the final subgrade alignment and sight distances. Turnout locations shall be subject to written approval by the Contract Administrator.
FULL BENCH CONSTRUCTION. DRAFT On the following road(s), and where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width. Purchaser shall end haul waste material to the location specified in Clause4-37 WASTE AREA LOCATION. Road Full Bench Location Comments 3+50 Spur 0+00 – 2+00 Full bench end-haul CP-850 95+00 – 103+00 Full bench end-haul CP-850 109+00 – 115+00 Full bench end-haul CP-850 120+00 -144+00 As needed SUBSECTION INTERSECTIONS, TURNOUTS AND TURNAROUNDS
FULL BENCH CONSTRUCTION. On the following road and where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width. Purchaser shall end haul waste material to the location specified in Clause 4-37 WASTE AREA LOCATION. Road Full Bench Location ST-37 52+63 to 56+97 4-21 TURNOUTS Purchaser shall construct turnouts intervisible with a maximum distance of 1,000 feet between turnouts unless otherwise shown on drawings. Locations may be adjusted to fit the final subgrade alignment and sight distances. Locations are subject to written approval by the Contract Administrator. Minimum dimensions are shown on the TYPICAL SECTION SHEET.
FULL BENCH CONSTRUCTION. On the following road, and where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width. Purchaser shall end haul waste material to the location specified in Clause 4‐37 WASTE AREA LOCATION. Road Full Bench Location D‐5410 1+20 to 3+50
FULL BENCH CONSTRUCTION. On the following road(s), and where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width. Purchaser shall end haul waste material to the location specified in Clause 0-00 XXXXX XXXX XXXXXXXX. Xxxx Full Bench Location PA-J-1215 9+00 – 17+00 SUBSECTION INTERSECTIONS, TURNOUTS AND TURNAROUNDS 4-21 TURNOUTS DRAFT Purchaser shall construct turnouts intervisible with a maximum distance of 1,000 feet between turnouts unless otherwise shown on drawings. Locations may be adjusted to fit the final subgrade alignment and sight distances. Locations changes are subject to written approval by the Contract Administrator. Minimum dimensions are shown on the TYPICAL SECTION SHEET.
FULL BENCH CONSTRUCTION. On the following road(s), and where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width. Purchaser shall end haul waste material to the location specified in Clause 4-37 WASTE AREA LOCATION. Road Full Bench Location PA-J-1215 9+00 – 17+00 SUBSECTION INTERSECTIONS, TURNOUTS AND TURNAROUNDS 4-21 TURNOUTS DRAFT Purchaser shall construct turnouts intervisible with a maximum distance of 1,000 feet between turnouts unless otherwise shown on drawings. Locations may be adjusted to fit the final subgrade alignment and sight distances. Locations changes are subject to written approval by the Contract Administrator. Minimum dimensions are shown on the TYPICAL SECTION SHEET.
FULL BENCH CONSTRUCTION. Where side slopes exceed 45%, Purchaser shall use full bench construction for the entire subgrade width except as construction staked or designed. Road Full Bench Location Comments E294424A 385+43 to 392+55 Full bench construction, excavated material may be side cast on side slopes up to 55% 408+56 to 409+61 Full bench construction, excavated material may be side cast on side slopes up to 55% 421+45 to 439+77 Full bench construction, excavated material may be side cast on side slopes up to 55% 422+89 to 423+98 Full bench construction, side slopes exceed 55%, excavated material shall be end hauled to designated waste areas 427+76 to 428+47 Full bench construction, side slopes exceed 55%, excavated material shall be end hauled to designated waste areas 430+25 to 431+21 Full bench construction, side slopes exceed 55%, excavated material shall be end hauled to designated waste areas E294533P 10+51 to 11+63 Full bench construction, excavated material may be side cast on side slopes up to 55% 15+79 to 17+16 Full bench construction, excavated material may be side cast on side slopes up to 55% 21+27 to 36+08 Full bench construction, excavated material may be side cast on side slopes up to 55% 37+45 to 43+63 Full bench construction, excavated material may be side cast on side slopes up to 55%
