Hierarchy of Safety Manuals and Variability due to different Deployments Sample Clauses

Hierarchy of Safety Manuals and Variability due to different Deployments. Hierarchy of Safety Manuals is also a key aspect. For example, if one node, down in the hierarchy, claims a SIL1 level but, higher in the hierarchy, an ancestor claims SIL3, then at least a warning should be raised. Depending on the architecture components with a lower SIL may be combined to result in a higher SIL (e.g., see IEC 61508-2, Chapter 7.4.3) Variability may complicate things further because perhaps, a given node can have one tile or multiple tiles depending on a variation point or, for example, one component may or may not exists depending on the configuration of the final system. The same project can also have multiple deployments, depending on the System Architect’s requirements. A given component, depending on the deployment, can be running on a different tile or a different core, and therefore, the claimed SIL must be checked against the SIL of the platform deployed.
Sample 1
AutoNDA by SimpleDocs

Related to Hierarchy of Safety Manuals and Variability due to different Deployments

  • Switching System Hierarchy and Trunking Requirements For purposes of routing ECI traffic to Verizon, the subtending arrangements between Verizon Tandem Switches and Verizon End Office Switches shall be the same as the Tandem/End Office subtending arrangements Verizon maintains for the routing of its own or other carriers’ traffic (i.e., traffic will be routed to the appropriate Verizon Tandem subtended by the terminating End Office serving the Verizon Customer). For purposes of routing Verizon traffic to ECI, the subtending arrangements between ECI Tandem Switches and ECI End Office Switches shall be the same as the Tandem/End Office subtending arrangements that ECI maintains for the routing of its own or other carriers’ traffic.

  • Uncontrollable Forces Tariff Provisions Section 14.1 of the CAISO Tariff shall be incorporated by reference into this Agreement except that all references in Section 14.1 of the CAISO Tariff to Market Participants shall be read as a reference to the Participating Generator and references to the CAISO Tariff shall be read as references to this Agreement.

  • Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Standard Service Features Ethernet Access allows Customer to terminate single and/or multiple Ethernet Virtual Circuits (EVCs) from Customer equipment onto a single Ethernet Access UNI.

  • Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.

  • Operating and Maintenance Manuals 58.1 If “as built” Drawings and/or operating and maintenance manuals are required, the Contractor shall supply them by the dates stated in the Contract Data.

  • CLASSIFICATION OF POSITIONS The University shall classify and/or reclassify all positions in the bargaining unit according to the nature and difficulty of duties assigned to and performed by the employee based on a current and accurate job description and shall assign to each position in the bargaining unit a classification title, number, and salary range. An employee new to his/her position will receive a copy of his/her job description upon hire. The appropriate administrator/supervisor will review the description with the employee. Materials used in determining classifications and reclassifications, such as class specifications and reclassification interpretation manuals, shall be readily available to the Union and employees on request.

  • Operation and Maintenance Manuals Receipts for transmittal of Operation and Maintenance Manuals, Brochures and Data to the Design Professional (or Commissioning Agent) as required by Section 6.1.1.5.

  • Demographic, Classification and Wage Information XXXXXX agrees to coordinate the accumulation and distribution of demographic, classification and wage data, as specified in the Letter of Understanding dated December 14, 2011, to CUPE on behalf of Boards of Education. The data currently housed in the Employment Data and Analysis Systems (EDAS) will be the source of the requested information.

Time is Money Join Law Insider Premium to draft better contracts faster.