Assuming Bank Portfolio Sales of Remaining Single Family Shared-Loss Loans The Assuming Bank shall have the right with the concurrence of the Receiver to liquidate for cash consideration, from time to time in one or more transactions, all or a portion of Single Family Shared-Loss Loans held by the Assuming Bank at any time prior to the Termination Date (“Portfolio Sales”). If the Assuming Bank exercises its option under this Section 4.1, it must give thirty (30) days notice in writing to the Receiver setting forth the details and schedule for the Portfolio Sale which shall be conducted by means of sealed bid sales to third parties, not including any of the Assuming Bank’s affiliates, contractors, or any affiliates of the Assuming Bank’s contractors. Sales of Restructured Loans shall be sold in a separate pool from Single Family Shared-Loss Loans not restructured. The Receiver’s review of the Assuming Bank’s proposed Portfolio Sale will be considered in a timely fashion and approval will not be unreasonably withheld, delayed or conditioned.
Alternative Risk Financing Programs The County reserves the right to review, and then approve, Contractor use of self-insurance, risk retention groups, risk purchasing groups, pooling arrangements and captive insurance to satisfy the Required Insurance provisions. The County and its Agents shall be designated as an Additional Covered Party under any approved program.
Applicable Policy (b) When providing the Services, the HSP will meet the Performance Standards and conditions identified in Schedule D and any applicable Project Funding Agreements.
Qualifying Mortgage Loans In order for a mortgage loan to be a Qualifying Loan it must meet all of the following criteria, which must be confirmed by the lender: • The collateral securing the mortgage loan is owner-occupied and the owner’s primary residence; and • The mortgagor has a first priority lien on the collateral; and • Either the borrower is at least 60 days delinquent or a default is reasonably foreseeable. Modification Process The lender shall undertake a review of its mortgage loan portfolio to identify Qualifying Loans. For each Qualifying Loan, the lender shall determine the net present value of the modified loan and, if it will exceed the net present value of the foreclosed collateral upon disposition, then the Qualifying Loan shall be modified so as to reduce the borrower’s monthly DTI Ratio to no more than 31% at the time of the modification. To achieve this, the lender shall use a combination of interest rate reduction, term extension and principal forbearance, as necessary. The borrower’s monthly DTI Ratio shall be a percentage calculated by dividing the borrower’s monthly income by the borrower’s monthly housing payment (including principal, interest, taxes and insurance). For these purposes, (1) the borrower’s monthly income shall be the amount of the borrower’s (along with any co-borrowers’) documented and verified gross monthly income, and (2) the borrower’s monthly housing payment shall be the amount required to pay monthly principal and interest plus one-twelfth of the then current annual amount required to pay real property taxes and homeowner’s insurance with respect to the collateral. In order to calculate the monthly principal payment, the lender shall capitalize to the outstanding principal balance of the Qualifying Loan the amount of all delinquent interest, delinquent taxes, past due insurance premiums, third party fees and (without duplication) escrow advances (such amount, the “Capitalized Balance”). In order to achieve the goal of reducing the DTI Ratio to 31%, the lender shall take the following steps in the following order of priority with respect to each Qualifying Loan:
Loan Amount 5. ACCOUNT NAME(S) .............................................................................................................................................................................. BANK NAME / BRANCH ...................................................................................................................................................................
Financial Institution with Only Low-Value Accounts An Estonian Financial Institution satisfying the following requirements:
Refinancing Preparation Advance; Capitalizing Front-end Fee and Interest (a) If the Loan Agreement provides for the repayment out of the proceeds of the Loan of an advance made by the Bank or the Association (“Preparation Advance”), the Bank shall, on behalf of such Loan Party, withdraw from the Loan Account on or after the Effective Date the amount required to repay the withdrawn and outstanding balance of the advance as at the date of such withdrawal from the Loan Account and to pay all accrued and unpaid charges, if any, on the advance as at such date. The Bank shall pay the amount so withdrawn to itself or the Association, as the case may be, and shall cancel the remaining unwithdrawn amount of the advance.”
Determine Whether a Non-U.S. Entity Is a Financial Institution a) Review information maintained for regulatory or customer relationship purposes (including information collected pursuant to AML/KYC Procedures) to determine whether the information indicates that the Account Holder is a Financial Institution.
COMMITMENT OF THE THREE PARTIES By signing7 this document, the staff member, the sending institution and the receiving institution/enterprise confirm that they approve the proposed mobility agreement. The sending higher education institution supports the staff mobility as part of its modernisation and internationalisation strategy and will recognise it as a component in any evaluation or assessment of the staff member. The staff member will share his/her experience, in particular its impact on his/her professional development and on the sending higher education institution, as a source of inspiration to others. The staff member and the beneficiary institution commit to the requirements set out in the grant agreement signed between them. The staff member and the receiving institution/enterprise will communicate to the sending institution any problems or changes regarding the proposed mobility programme or mobility period. The staff member Name: Signature: Date: The sending institution Name of the responsible person: Signature: Date: The receiving institution/enterprise Name of the responsible person: Signature: Date: 1 Adaptations of this template: In case the mobility combines teaching and training activities, the mobility agreement for teaching template should be used and adjusted to fit both activity types. In the case of mobility between Programme and Partner Countries, this agreement must be always signed by the staff member, the Programme Country HEI as beneficiary and the Partner Country HEI as sending or receiving organisation. In case of mobility from Partner Country HEIs to Programme Country enterprises the last box should be duplicated to include the signature of the Programme Country HEI (the beneficiary) and the receiving organisation (four signatures in total).
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
