Imperfections. Any and all errors, defects and imperfections in any action by Bank in replevin, foreclosure or other court process or in connection with any other action related to any of the Loan Documents or the transactions contemplated therein.
Imperfections. TS-743 Inclusions in glass originate from impurities in the batch or cullet, or are combined from furnace refractories. Common forms of inclusions include aluminous stones, iron stones, and silicon. Nickel sulfide stones are uncommon, microscopic defects in glass, and may cause breakage. Delayed breakage may occur when a nickel sulfide stone is present near the center of the glass thickness. TS-744 The tempering process rarely introduces imperfections into glass. The basic glass may contain bubbles, vents, chips, and inclusions which, if accepted or not revealed by inspection before tempering can cause breakage in the initial heating or final quench operations. If inclusions are not eliminated by self-destruction during the tempering process, in rare cases they may lead to failure at a later time.
Imperfections and irregularities in title to any property which in the aggregate do not materially impair the marketability or use of such property for the purposes for which it is or may reasonably be expected to be held;
Imperfections. Imperfections are all faults that do not affect the Quality of Service. The faults must be solved before general availability. Depending on the possibility, the solution may be covered in future upgrades.
Imperfections. After the Closing, Boise Cascade shall cooperate with Purchaser to clear any imperfections of title to the Realty and Timberlands.
Imperfections. breakage. Delayed breakage may occur when a nickel sulfide stone is present near the center of the glass thickness.
Imperfections. TS-279 Inclusions in glass originate from impurities in the batch or cullet, or are combined from furnace refractories. Common forms of inclusions include aluminous stones, iron stones, and silicon. Nickel sulfide stones are uncommon, microscopic defects in glass, and may cause breakage. TS-280 The tempering process rarely introduces imperfections into glass. The basic glass may contain bubbles, vents, chips, and inclusions which, if accepted or not revealed by inspection before tempering can cause breakage in the initial heating or final quench operations. If inclusions are not eliminated by self-destruction during the tempering process, in rare cases they may lead to failure at a later time.
Imperfections faults, deficiencies and other matters of discrepancies revealed during the Pre-delivery Tests, shall be listed in a protocol signed by both Parties, the «Pre-delivery Test protocol». Unless otherwise agreed, any imperfection, faults, deficiency or other matter of discrepancy shall be remedied immediately. If the number of defects on a Trainset during the Pre-delivery Test exceed zero (0) significant failures or zero (0) major failures, ref. Exhibit A4-1, then NT is entitled to extend the Pre-delivery Test until the relevant Trainset has produced a continuous distance of at least 1000 Trainset kilometres without exceeding the above number of failures. If any of the limits of significant and major failures above are exceeded for any of the Trainsets which have been used to carry out the Pre-delivery Test, then the Contractor shall inform NT of the defect(s) which have caused the Trainset to exceed any of the limits set out in reasonable detail. NT is then entitled to demand that further Trainsets, in addition to the first three (3) to be delivered, will be subject to a Pre-delivery Test.
Imperfections faults, deficiencies and other matters of discrepancies revealed during the Production Plant Inspection, shall be listed in a protocol signed by both Parties, the «Production Plant Inspection Protocol». Unless otherwise agreed, any imperfection, faults, deficiency or other matter of discrepancy shall be remedied immediately. If any Trainset or part of any Trainset fails to pass the tests conducted during the Production Plant Inspection, NT may request a new test to be undertaken in relation to the defective component and depending systems on the same terms and conditions. All reasonable costs of NT directly related to the rejected test shall be borne by the Contractor upon an invoice from NT, or alternatively deducted by NT from the relevant part payment. If NT fails to attend the notified Production Plant Inspection, the Contractor is authorised to proceed with the Production Plant Inspection. The Production Plant Inspection is deemed to have occurred and the Contractor is authorised to sign the protocol on its own.
Imperfections faults, deficiencies and other matters of discrepancies revealed during the Pre-PTO tests, shall be listed in a protocol signed by both parties, the «Pre-PTO test protocol». Unless otherwise agreed, any imperfection, faults, deficiency or other matter of discrepancy shall be remedied immediately. If the number of defects on a Trainset during the Pre-PTO Test exceed zero (0) significant failures or zero (0) major failures, ref. Exhibit A4-1, then NT is entitled to extend the Pre-delivery Test until the relevant Trainset has produced a continuous distance of at least 3 000 Trainset kilometres without exceeding the above number of failures before acceptance.
