Common use of Inscriptions Clause in Contracts

Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2: 2.3.1.1. The trade name or xxxx of the applicant; 2.3.1.2. The rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm; 2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category; 2.3.1.5. A space of sufficient size to accommodate the approval xxxx. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2:bulb: 2/ 2.3.1.1. The the trade name or xxxx of the applicant; 2.3.1.2. The the rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The the international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm; 2.3.1.4. The the rated wattage (in the sequence, high wattage/low wattage filament for dual-dual- filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category; 2.3.1.5. A a space of sufficient size to accommodate the approval xxxx. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2: 2.3.1.1. The trade name or xxxx mark of the applicant; 2.3.1.2. The rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm; 2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category; 2.3.1.5. A space of sufficient size to accommodate the approval xxxxmark. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2:bulb: 2/ 2.3.1.1. The the trade name or xxxx of the applicant; 2.3.1.2. The the rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The the international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm; 2.3.1.4. The the rated wattage (in the sequence, high wattage/low wattage filament for dual-dual- filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category; 2.3.1.5. A a space of sufficient size to accommodate the approval xxxxmark. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps light sources submitted for approval shall bear on the cap or bulb2: 2.3.1.1. The trade name or xxxx mark of the applicant; 2.3.1.2. The rated voltage. However, for filament lamps light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp light source type does not exceed 7.5 mm; 2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lampslight sources); this need not be indicated separately if it is part of the international designation of the relevant filament lamp light source category; 2.3.1.5. A space of sufficient size to accommodate the approval xxxxmark. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps light sources meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2:bulb:2 2.3.1.1. The trade name or xxxx of the applicant; 2.3.1.2. The rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm; 2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category; 2.3.1.5. A space of sufficient size to accommodate the approval xxxx. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.

Inscriptions. 2.3.1. Filament lamps light sources submitted for approval shall bear on the cap or bulb2: 2.3.1.1. The trade name or xxxx of the applicant; 2.3.1.2. The rated voltage. However, for filament lamps light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked; 2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp light source type does not exceed 7.5 mm; 2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lampslight sources); this need not be indicated separately if it is part of the international designation of the relevant filament lamp light source category; 2.3.1.5. A space of sufficient size to accommodate the approval xxxx. 2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval. 2.3.3. Halogen filament lamps light sources meeting the requirements of paragraph 3.7. below shall be marked with a "U". 2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.