Common use of Job Control Clause in Contracts

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule for Sampling and Testing for materials. The testing shall include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPA) for Hot Mix Asphalt, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. Hot Mix Asphalt Testing  Level l-A  Level l-B  Level II  All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Level l-A, Level l- ii. Concrete Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Concrete Testing  Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included in the QAP Program e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. :  Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP.  Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP.  Soils and Base, HMAC o SB 101 Properties Specialist DocuSign Envelope ID: 5B10DF3F-01CC-4436-8E6B-37B38F170AB1 o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in SB101, SB102, SB103, SB201 and SB202 testing will be administered by the state central lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. : DocuSign Envelope ID: 371795F3-9F9E-4276-BC7C-7A8A7988B2B9 • Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP. • Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP. • Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in SB101, SB102, SB103, SB201 and SB202 testing will be administered by the state central lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below.. DocuSign Envelope ID: 48417968-4E6D-4650-8591-F6023784BA9E d. The Engineer shall provide certified technicians to perform the following tests: i. : • Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP. • Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP. • Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in SB101, SB102, SB103, SB201 and SB202 testing will be administered by the state central lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. :  Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP.  Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP.  Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist DocuSign Envelope ID: DA7E8B68-9EB5-4D54-A1F2-12D96602168D WAs Used Legacy Xxxxxxxx Xx. 00-0XXX0000 XxxxxxXxxx Xxxxxxxx Xx. 0000 o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in SB101, SB102, SB103, SB201 and SB202 testing will be administered by the state central lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. : • Hot Mix Asphalt Testing  Testing, HMAC o Level l-A  1A o Level l-B  1B o Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Level l-A1A, Level l- ii1B, or Level 2 will be administered by the State central lab per the QAP. • Concrete Testing, ACI-American Concrete Association o Concrete Field Testing Technician - Grade I o Concrete Strength Testing Technician DocuSign Envelope ID: DA839420836BB159-0C3D-4A9FC55D-4DEE-B41B-3205C3B9D244  QAP Program for Concrete Testing  AADF-3BB0976143B0 WAs Used Contract No. 08-8IDP5002 o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the State central lab per the QAP. • Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 201 Strength Specialist o SB 202 Compressive Strength Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in SB101, SB102, SB103, SB201 and SB202 testing will be administered by the State central lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in the State's Guide Schedule to Sampling and Testing dated 2016. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QA and QC) plan Plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. : • Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP. • Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP. • Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o AGG101 Aggregate Specialist DocuSign Envelope ID: ED59041B-65A8-4D71-AA4B-B69EF8A562AD o Other tests outlined in the QAP Program e. The Engineer shall perform Manual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in AGG101, SB101, SB102, SB103, SB201 and SB202 testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016. Follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may will be increased as directed administered by the Statestate district lab per the QAP.

Job Control. 1. The Engineer shall perform all sampling and testing of components and materials in accordance with the standard specifications, and all other standard and special specifications and special provisions applicable in this agreement. Meet The Engineer shall meet the minimum sampling frequencies set out in the TxDOT 2016 Guide Schedule applicable to the project for Sampling and Testing for materials. The testing shall must include the following materials and all the components of the materials listed: Asphalt, Concrete, Soils Soils, and Aggregates. The estimated number of samples and tests are based on quantities in the executed construction contract. a. The Engineer shall ensure the testing is completed and input into Site Manager. NOTE: The contractor is responsible for testing Item 360 Concrete Paving. b. The Engineer shall provide certified personnel, outlined in their Quality Assurance and Quality Control (QA/QC) plan plan, that are knowledgeable of all materials testing procedures. All personnel performing acceptance tests must provide certifications and must maintain the certifications throughout the project. The State reserves the right to require replacement of any technician during this contract if performance is determined to be unsatisfactory or the technician fails to maintain appropriate certifications. c. The Engineer shall provide technicians certified in accordance with TxDOT Quality Assurance Programs for Construction (QAP) or other State approved programs, such as the Texas Asphalt Pavement Association (TxAPATXAPA) for Hot DocuSign Envelope ID: E72D88A3-1FD8-4CA6-9F94-B5B0362A640F Mix Asphalt, ACI for concrete, and the Soils and Base Certification Program, as listed below. d. The Engineer shall provide certified technicians to perform the following tests: i. : • Hot Mix Asphalt Testing  Testing, HMAC o Xxxxx 0X o Level l-A  1B o Level l-B  Level II  2 o All other tests in the Manual of Testing Procedures 200-F Series or ASTM Procedures not covered in Xxxxx 0X, Xxxxx 0X, or Level l2 will be administered by the state central lab per the QAP. • Concrete Testing, ACI-A, Level l- ii. American Concrete Association o Concrete Field Testing DocuSign Envelope ID: DA839420-0C3D-4A9F-B41B-3205C3B9D244  QAP Program for Technician - Grade I o Concrete Strength Testing  Technician o Other tests outlined in the Manual of Testing Procedures 400-A Series or ASTM Procedures that are not included covered by ACI Field and Strength Testing will be administered by the state central lab per the QAP. • Soils and Base, HMAC o SB 101 Properties Specialist o SB 102 Field Specialist o SB 103 Materials Analyst Specialist o SB 000 Xxxxxxxx Specialist o SB 202 Compressive Strength Specialist o AGG101 Aggregate Specialist o Other tests outlined in the QAP ProgramManual of Testing Procedures 100-E Series or ASTM Procedures that are not covered in AGG101, SB101, SB102, SB103, SB201 and SB202 testing will be administered by the state district lab per the QAP. e. The Engineer shall perform testing on the project. These tests include all tests listed in State's Guide Schedule to Sampling and Testing dated 2016June 2018. Follow The Engineer shall follow the State’s Guide Schedule of Sampling and Testing to establish testing frequencies. Testing frequencies may be increased as if directed by the State.