Landscape Irrigation Clause Samples

The Landscape Irrigation clause sets out the requirements and standards for installing and maintaining irrigation systems in landscaped areas of a property. It typically details the types of irrigation methods permitted, such as drip or sprinkler systems, and may specify responsibilities for regular maintenance, repairs, and water usage efficiency. By clearly defining these expectations, the clause helps ensure that landscaping remains healthy and attractive while promoting responsible water management and preventing disputes over system upkeep.
Landscape Irrigation a. The automatic irrigation system shall be designed by a Texas Licensed Irrigator. b. Applicable campus irrigation standards and specifications will be provided to the A/E by the UTH Project Manager. c. Potable water protection shall be as per local code requirements. Rev. Date Remarks 10/1/10 Add A/E requirement for xeriscape compliance letter A. GENERAL REQUIREMENTS 2 B. DESIGN REVIEW SUBMITTAL REQUIREMENTS 4 C. ENERGY CONSERVATION 5 D. CONTROLS 6 E. UTILITIES 7 F. PLUMBING 8 G. HEATING, VENTILATING, AIR CONDITIONING 9 H. FIRE SPRINKLER SYSTEMS 14 I. COORDINATION OF DESIGN 15 A. GENERAL REQUIREMENTS‌ 1. The UT System Design Guidelines and Guideline Specifications for mechanical services shall be utilized by the Architect/Engineer in preparation of the contract documents. The specifications shall be edited to conform to the particular project, systems, and campus. 2. The criteria for a particular mechanical system will vary somewhat from campus to campus which may change certain parameters of initial design considerations. Design engineer is responsible for acquiring a local campus standard, if one exists, and adjusting design to standard as appropriate and as approved by the UTH Project Manager. 3. Do not assume the Owner will provide, connect, or otherwise perform any services without specific prior agreement. 4. Room names and numbers shall appear on all mechanical, plumbing, and fire protection floor and partial floor plans. Column lines or designations shall appear on all Mechanical, Electrical and Plumbing (MEP) floor plan sheets, sections, and partial floor plan drawings (e.g., vaults and mechanical rooms) as they appear on Architectural sheets; such drawings shall also have graphic scales and north arrows as applicable. All MEP drawing sheets shall have the UTH project name and number shown in the title block. 5. Systems shall be designed to comply with ANSI standards, including supplements. 6. Flow diagrams shall be drawn for each piping system including but not limited to steam, heating water, chilled water, domestic hot and cold water, distilled water, fire standpipe, oxygen, compressed air, condenser water, gas, vacuum, and refrigerant systems. Mains and major branches shall show quantities of flow with size. All valve sizes shall be indicated. 7. Plumbing and air conditioning systems shall be drawn as separate drawings. These systems may be combined on common drawings only by written permission of UTH. A complete roof plan shall be included b...
View SourceView Similar (2)
Landscape Irrigation a. The automatic irrigation system shall be designed by a Texas Licensed Irrigator. b. Applicable campus irrigation standards and specifications will be provided to the A/E by the CPO Project Manager. c. Potable water protection shall be as per local code requirements. Rev. Date Remarks 10/1/10 Add A/E requirement for xeriscape compliance letter 8/29/19 Revision to UTHSCSA, CPO MECHANICAL CRITERIA A. GENERAL REQUIREMENTS 2 B. DESIGN REVIEW SUBMITTAL REQUIREMENTS 4 C. ENERGY CONSERVATION 5 D. CONTROLS 6 E. UTILITIES 7 F. PLUMBING 8 G. HEATING, VENTILATING, AIR CONDITIONING ...…………………….……… 9 H. FIRE SPRINKLER SYSTEMS 13 I. COORDINATION OF DESIGN 14
View SourceView Similar (2)
Landscape Irrigation 
View SourceView Similar (2)

Related to Landscape Irrigation

  • Irrigation An irrigation reduced pressure zone (hereinafter referred to as “RPZ”) is required for any irrigation systems and must be installed by the Developer and/or eventual lot owner and tested in accordance with the Minnesota Department of Health Guidelines for Designing Backflow Prevention Assembly Installations (hereinafter referred to as “Guidelines”). The initial test results and certification shall be submitted to the City of Maple Grove Public Works Department. Subsequently, the RPZ must be tested, per the Guidelines, at least annually by a certified tester with the results reported to the City of Maple Grove Building Department and the RPZ must be rebuilt as needed in accordance with the Guidelines. Test/rebuilt reports shall be mailed or faxed to the City of Maple Grove Building Department at (▇▇▇) ▇▇▇-▇▇▇▇. The irrigation system shall be designed and the Plans shall be modified accordingly, prior to the issuance of any permits for the development of the Property, to accommodate a 1-inch water meter and a maximum flow of 50 gallons per minute.

  • Landscaping The Owner will, before its plan of subdivision is released for registration, pay to the Town in lieu of planting any trees on the public streets within the plan, the amount shown for the purpose upon Schedule “J”.

  • Sidewalks doorways, vestibules, halls, stairways and other similar areas shall not be obstructed by Tenant or used by Tenant for any purpose other than ingress and egress to and from the Premises. No rubbish, litter, trash, or material shall be placed, emptied, or thrown in those areas. At no time shall Tenant permit Tenant’s employees to loiter in Common Areas or elsewhere about the Building or Property.

  • Restrooms The restrooms, toilets, urinals, vanities and the other apparatus shall not be used for any purpose other than that for which they were constructed, and no foreign substance of any kind whatsoever shall be thrown therein. The expense of any breakage, stoppage or damage resulting from the violation of this rule shall be borne by the Tenant whom, or whose employees or invitees, shall have caused it.

  • Drainage ▪ Prevent silt bearing road surface and ditch runoff from delivering sediment to any streams or wetlands. ▪ Maintain rolling dips and drivable waterbars as needed to keep them functioning as intended. ▪ Maintain headwalls to the road shoulder level with material that will resist erosion. ▪ Maintain energy dissipaters at culvert outlets with non-erodible material or rock. ▪ Keep ditches, culverts, and other drainage structures clear of obstructions and functioning as intended. ▪ Inspect and clean culverts at least monthly, with additional inspections during storms and periods of high runoff. This shall be done even during periods of inactivity. ▪ Perform preventative maintenance work to safeguard against storm damage, such as blading to ensure correct runoff, ditch and culvert cleaning, and waterbar maintenance.