MATERIAL SAMPLES Sample Clauses

MATERIAL SAMPLES. 6.6.1 The Contractor shall furnish all samples required by the drawings and specifications or that may be requested by the Project Manager of any and all materials or equipment it proposes to use. Unless specifically required, samples are not to be submitted with the bid. 6.6.2 No materials or equipment of which samples are required shall be used on the work until the Project Manager has received and accepted the samples. If the Contractor proceeds to use such materials before the Project Manager accepts the samples, the Contractor shall bear the risk. 6.6.3 Contractor shall furnish two (2) copies of a transmittal letter with each shipment of samples. The letter shall provide a list of the samples, the name of the building or work for which the materials are intended and the brands of the materials and names of the manufacturers. Also, each sample submitted shall have a label indicating the material represented, its place of origin, the names of the producer, the Contractor and the building or work for which the material is intended. Samples of finished materials shall be marked to indicate where the materials represented are required by the drawings or specifications. 6.6.4 Acceptance of any sample(s) shall be only for the characteristics or for the uses named in such acceptance and for no other purpose. Acceptance of samples shall not change or modify any contract requirement. All samples will be provided by the Contractor at no extra cost to the Department. See also Section 5.5,
Sample 1Sample 2Sample 3See All (24)
AutoNDA by SimpleDocs
MATERIAL SAMPLES. The same procedure shall be followed for any re-submittals. All shop drawings, material samples and submittal literature shall be properly identified with job name, product type, model number and certification stamp. All shop drawings, material samples and/or submittal literature must be mailed or hand-delivered to Contractor’s office. Contractor will not accept or process any submittals sent by facsimile. Any exceptions to the required submittal material must be requested in writing and authorized by Contractor before they are submitted to Contractor for Owner review.
Sample 1Sample 2Sample 3See All (4)
MATERIAL SAMPLES. If any of the Information delivered by Liquidmetal or its Representatives to Company consists of samples of amorphous alloys or samples of other materials (referred to as "Materials"), then Company shall not take or send the Materials to any location other than the facilities of the Company without the prior written consent of Liquidmetal. The Company acknowledges that the Materials may be experimental in nature and shall be used with prudence and appropriate caution. The Company will not engage in any testing or processing of the Materials (including, but not limited to, any grinding, melting, milling, or machining of the Materials) without the express prior written consent of Liquidmetal. In no event shall Liquidmetal be liable for any use by the Company or its Representatives for any loss, claim, damage, or liability, of any kind or nature, that may arise from or in connection with the use, handling, or storage of the Materials, and the Company agrees to indemnify and hold harmless Liquidmetal and Liquidmetal's Representatives from any liability, loss, or damage they may suffer as a result of claims, demands, costs, or judgments against them arising out of the use or disposition of the Materials by the Company.
Sample 1Sample 2
MATERIAL SAMPLES. 3.13.1 The Design-Builder shall furnish for the approval of the Engineer, any samples required by the specifications or that may be requested by the Engineer of any and all materials or equipment he proposes to use. Unless specifically required, samples are not to be submitted with the proposal. 3.13.2 No materials or equipment of which samples are required to be submitted for approval shall be used on the work until such approval has been given by the Engineer, except at the Design-Builder’s risk and expense. 3.13.3 Each sample submitted shall have a label indicating the material represented, its place of origin, and the names of the producer, the Design-Builder and the building or work for which the material is intended. Samples of finished materials shall be so marked as to indicate where the materials are required by the drawings or specifications. 3.13.4 A letter in duplicate by the Design-Builder shall accompany each shipment of samples submitted and shall contain a list of the samples, the name of the building or work for which the materials are intended and the brands of the materials and names of the manufacturers. 3.13.5 The approval of any sample shall be only for the characteristics or for the uses named in such approval and for no other purpose. Approval of a sample shall not be construed as to change or modify any contract requirement. 3.13.6 All samples will be provided by the Design-Builder at no extra cost to the project or to the City. 3.13.7 All materials and equipment approved by Design-Builder must be submitted to the City for record and final conformance review upon approval. Provide three (3) copies of each submittal with indications of approval by the Design-Builder’s Architect of Record and the Design- Builder.
Sample 1
MATERIAL SAMPLES. 9 Article 4 B&L License........................................ 9
Sample 1
MATERIAL SAMPLES. All materials believed by either party to be useful in the design of Products and prepared by such party in the course of any of its research under this Agreement will be discussed with the other party and samples of such materials will be submitted to the other party upon request.
Sample 1
MATERIAL SAMPLES. During the course of the work, the Project Representative shall be allowed to secure samples of the materials being used from the containers on the jobsite and submit them to an independent testing laboratory for comparison. All non-approved material installed or stored shall be removed from the construction site until it has been tested. Installed materials that do not conform to the Contract shall be removed at no additional cost to King County. May 2017 C01025C17 Georgetown Wet Weather Treatment Station 07513 - 2 MODIFIED BITUMEN ROOFING SYSTEM
Sample 1
AutoNDA by SimpleDocs
MATERIAL SAMPLES. Samples of all primary materials to be used in the fabrication of the Artwork.
Sample 1

Related to MATERIAL SAMPLES

  • MATERIAL SAFETY All manufacturers, importers, suppliers, or distributors of hazardous chemicals doing business in this State must provide a copy of the current Material Safety Data Sheet (MSDS) for any hazardous chemical to their direct purchasers of that chemical.

  • Material Safety Data Sheet Seller shall provide to Buyer with each delivery any Material Safety Data Sheet applicable to the work in conformance with and containing such information as required by the Occupational Safety and Health Act of 1970 and regulations promulgated thereunder or its State approved counterpart.

  • MATERIAL SAFETY DATA SHEETS As applicable, Contractor shall provide Purchaser with all appropriate Material Safety Data Sheets (“MSDS”) at the time of delivery of each shipment of Goods which requires such compliance and/or and for materials used by Contractor while performing Services and any updates of the same.

  • Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!