Meter Inaccuracy Sample Clauses

Meter Inaccuracy. If, at any time, any meter is found to be out of service or registering inaccurately in any percentage, it shall be adjusted at once by Shipper to read accurately within the limits prescribed by the meter's manufacturer. If such equipment is out of service or inaccurate by an amount exceeding three percent (3%) of a reading corresponding to the average flow rate for the period since the last test, the previous readings shall be corrected for the period that the meter is known to be inaccurate, or, if not known, a period of one-half (1/2) the elapsed time since the last test. The volume of Shipper's Gas delivered during such period shall be estimated by Gatherer either (i) by using the data recorded by any check measuring equipment if installed and accurately registered, (ii) by correcting the error if the percentage of error is ascertainable by calibration, test, or mechanical calculation or, if neither such method is feasible, (iii) by estimating the quantity delivered based upon deliveries under similar conditions during a period when the equipment registered accurately. No volume correction shall be made for metering inaccuracies of three percent (3%) or less.
Sample 1Sample 2Sample 3See All (19)
AutoNDA by SimpleDocs
Meter Inaccuracy. Should the Meter be determined to be inaccurate beyond the manufacturer’s guaranteed range of accuracy, the Cooperative shall repair or replace the malfunctioning Meter at its earliest convenience, recognizing that time is of the essence. Additionally, the Meter shall be assumed to have been inaccurate since the last inspection or test and the following month’s billing will be adjusted taking into account the nature of the inaccuracy to show a credit or additional charge to the Project Participant for the metered flow for the time interval between the date of the last Meter accuracy inspection or test and the date the Meter was corrected.
Sample 1Sample 2Sample 3See All (9)
Meter Inaccuracy. If the Meter is determined to be inaccurate and such inaccuracy exceeds ANSI C12.20 Standard accuracy range or, if more stringent, as defined by the CPUC or other applicable governing authority for electricity Meters, and if the date that such inaccuracy commenced is known, then all invoices since the date on which such inaccuracies began shall be corrected. If it is unknown when the Meter’s inaccuracy commenced (if such evidence exists, such date will be used to adjust prior invoices), then the invoices covering the period of time since the last meter test shall be adjusted for the amount of the inaccuracy on the assumption that the inaccuracy persisted during one half of such period. Adjustments which benefit Trustees shall be reflected on the next invoice following the date of determination of the inaccuracy. Adjustments which benefit Licensee shall be included on Licensee’s next invoice to Trustees.
Sample 1Sample 2Sample 3See All (5)
Meter Inaccuracy. If, at any time, any meter is found to be out of service or registering inaccurately in any percentage, it shall be adjusted at once by Atlas America to read accurately within the limits prescribed by the meter's manufacturer. If such equipment is out of service or inaccurate by an amount exceeding three percent (3%) of a reading corresponding to the average flow rate for the period since the last test, the previous readings shall be corrected for the period that the meter is known to be inaccurate, or, if not known, a period of one-half (1/2) the elapsed time since the last test; provided, however, the Operating Fee and Gathering Fee previously paid will be adjusted retroactively between the parties based on any corrected volumes but the volumes allocated among shippers on the Gathering System shall be adjusted only prospectively. The volume of the Resource Entities' Gas delivered during such period shall be estimated by Atlas America either (a) by using the data recorded by any check measuring equipment if installed and accurately registered, (b) by correcting the error if the percentage of error is ascertainable by calibration, test, or mechanical calculation or, if neither such method is feasible, (c) by estimating the quantity delivered based upon deliveries under similar conditions during a period when the equipment registered accurately. No volume correction shall be made for metering inaccuracies of three percent (3%) or less.
Sample 1Sample 2
Meter Inaccuracy. If a Meter is determined to be inaccurate and such inaccuracy exceeds industry standard tolerance allowances or as defined by the CPUC for electric Meters and if the date that such inaccuracy commenced is known, then all invoices since the date on which such inaccuracies began shall be corrected. If it is unknown when the Meter inaccuracy commenced then the invoices covering the period of time since the last Meter test shall be adjusted for the amount of the inaccuracy on the assumption that the inaccuracy persisted during one half of such period. Adjustments which benefit HOST shall be reflected on the next invoice following the date of determination of the inaccuracy. Adjustments which benefit CONTRACTOR shall be included on CONTRACTOR’s next invoice to HOST.‌
Sample 1
Meter Inaccuracy. If any tested or retested Metering Equipment is found to be not accurate within the tolerance limits set forth in the Direct Access Standards for Metering and Meter Data established by the CPUC, Seller shall promptly arrange for the correction or replacement of the affected portion of the Metering Equipment, at its expense, and Seller shall submit revised monthly invoices, pursuant to Section 6.2, covering the entire applicable time period in order to conform fully such adjustments to the meter data. If any tested or retested Metering Equipment is found to be not accurate within the tolerance limits and the Parties cannot otherwise agree as to the duration of the inaccuracy, the inaccuracy will be deemed to have occurred during the period from the date of discovery of the inaccuracy to the earlier of (i) one- half of the period from such discovery to the date of the last testing or retesting of the Metering Equipment (or relevant part thereof), as applicable, or (ii) if no prior testing or retesting is available, one hundred eighty (180) days. Any amounts due by Buyer or to be refunded by Seller as a result of any meter that is not accurate within the tolerance limits will be invoiced by the Party owed such amount on the next date on which such Party is to render an invoice in accordance with Section 6.1 following discovery of such inaccuracy.
Sample 1
Meter Inaccuracy. It is critical for any Utility to be able to identify those meters within the utility system that perform below accepted levels of efficiency. Three typical contributing factors are: ο Failure of Meters and Other Mechanical Devices ο Lack of System Capabilities ο Budgetary Limitations
Sample 1
AutoNDA by SimpleDocs
Meter Inaccuracy. If, at any time, any metering equipment is found to be inaccurate by a margin of greater than that allowed by Transmission Owner system operations or for BPA billing purposes, Transmission Owner or Generator, depending on whose equipment has malfunctioned, shall cause such metering equipment to be made accurate or replaced. Meter readings for the period of inaccuracy shall be adjusted so far as the same can be reasonably ascertained.
Sample 1
Meter Inaccuracy. If, at any time, any meter is found to be out of service or registering inaccurately in any percentage, it shall be adjusted at once to read accurately within the limits prescribed by the meter's manufacturer. If such equipment is out of service or inaccurate by an amount exceeding three percent (3%) of a reading corresponding to the average flow rate for the period since the last test, the previous readings shall be corrected for the period that the meter is known to be inaccurate, or, if not known, a period of one-half (1/2) the elapsed time since the last test. The volume of Shipper's Gas delivered during such period shall be estimated either (i) by using the data recorded by any check measuring equipment if installed and accurately registered, (ii) by correcting the error if the percentage of error is ascertainable by calibration, test, or mechanical calculation or, if neither such method is feasible, (iii) by estimating the quantity delivered based upon deliveries under similar conditions during a period when the equipment registered accurately. No volume correction shall be made for metering inaccuracies of three percent (3%) or less.
Sample 1

Related to Meter Inaccuracy

  • Representation / Warranty a. All statements contained herein or made in the Proclamation of Sale or otherwise relating to the Property are made without responsibility on the part of the Assignee, the Assignee’s Solicitors, the Auctioneer or their respective servants or agents. b. Such statements are statements of opinions and are not to be taken or relied upon as or implying a statement or representation of fact and any intending bidders must satisfy themselves by inspection or otherwise as to the correctness of any such statements. c. Neither the Assignee, the Assignee’s Solicitors, the Auctioneer nor any person in their employment has any authority to make or give any representation or warranty whatsoever in relation to the Property. d. No error, mis-statement, mis-description, omission or the existence of and/or intention for encroachment or acquisition shall annul the sale nor shall any abatement or compensation be allowed in respect thereof.

  • Tenant Representation and Warranty Tenant hereby represents and warrants to Landlord that (i) neither Tenant nor any of its legal predecessors has been required by any prior landlord, lender or Governmental Authority at any time to take remedial action in connection with Hazardous Materials contaminating a property which contamination was permitted by Tenant of such predecessor or resulted from Tenant’s or such predecessor’s action or use of the property in question, and (ii) Tenant is not subject to any enforcement order issued by any Governmental Authority in connection with the use, storage, handling, treatment, generation, release or disposal of Hazardous Materials (including, without limitation, any order related to the failure to make a required reporting to any Governmental Authority). If Landlord determines that this representation and warranty was not true as of the date of this lease, Landlord shall have the right to terminate this Lease in Landlord’s sole and absolute discretion.

  • Accuracy of the Purchaser’s Representations and Warranties The representations and warranties of each Purchaser shall be true and correct in all material respects as of the date when made and as of the Closing Date as though made at that time, except for representations and warranties that are expressly made as of a particular date, which shall be true and correct in all material respects as of such date.

  • Accuracy of Representations and Warranties The representations and warranties of Purchaser contained in this Agreement shall have been true in all material respects on the date hereof and shall be true in all material respects on and as of the Closing Date with the same force and effect as though made on and as of the Closing Date.

  • Preserve Accuracy of Representations and Warranties Each party hereto will refrain from taking any action which would render any of its representations and warranties contained in this Agreement untrue, inaccurate or misleading as of Closing and the Effective Time. Through Closing, each party will promptly notify the other parties of any lawsuit, claim, audit, investigation, administrative action or other proceeding asserted or commenced against such party that may involve or relate in any way to another party to this Agreement. Each party hereto will promptly notify the other parties of any facts or circumstances that come to its attention and that cause, or through the passage of time may cause, any of a party's representations, warranties or covenants to be untrue or misleading at any time from the date hereof through Closing.

  • Servicer Representations and Warranties The Servicer represents and warrants, as of the date of this Agreement and, except as otherwise provided, throughout the term of this Agreement, that the statements set forth below in this Section 5.2 are true and accurate. Relative to the Servicer:

  • Representations and Warranty 8.1 You represent and warrant that you and the Representative, will perform all activities relating to the Service: (a) in accordance with Best Industry Practice and in a professional and lawful manner; (b) if applicable, using appropriately skilled and experienced Representatives whose identity, address and right to live and work in Bermuda and (to the maximum extent permissible) whose absence of relevant criminal records has been verified; (c) in strict accordance with the standards and timelines set out in Schedule 1 or Appendix 1, free of defects, errors or faults, in order to meet the Objectives of this Agreement; and (d) in accordance with applicable law including PIPA, rules, regulations and guidelines or policies provided by us. 8.2 You represent and warrant that: (a) upon installation, the Equipment will be compatible with existing equipment and software on our systems and the Equipment will meet all the technical documentation and requirements required to operate the Service in accordance with our requirements and objectives; and (b) you have the right to license all intellectual property rights in a Service, Software and Documents, to us. 8.3 You represent and warrant that you are not subject to any contractual obligation, compliance with which is likely to have a material adverse effect on your ability to perform your obligations and you will notify us immediately if you have any actual or potential conflict of interest which might affect your ability to provide the Service. 8.4 You represent and warrant that this Agreement is executed by you or by your duly authorized Representative and that you have obtained all required authorizations and capacity in order that you can fulfill your obligations. 8.5 You declare that you are in possession of all Consents necessary for the provision of a Service and you will maintain such Consents at all times while providing the Service. 8.6 You shall procure the benefit of any warranties or guarantees in respect of goods and materials you supply to us and provide copies of such warranties or guarantees. 8.7 You declare that all payments to us, including but not limited to, taxes and social insurance, are current. 8.8 You shall provide information or sign any other agreements necessary or as requested by us, in order that either you or we can fulfill their obligations under this Agreement. 8.9 You represent and warrant that you are that a Service does not infringe or misappropriate any patent, copyright, trade secret or other intellectual property right of a third party or breach of any law applicable to it. 8.10 You represent and warrant that you are fully satisfied as to the scope and nature of the Service and of your obligations under this Agreement and that you have the corporate power and authority to enter into, and perform your obligations under, the Agreement.

  • Correctness of Representations and Warranties The representations and warranties made by Purchaser in this Agreement to be made on or prior to the Agreement Date or Closing Date, as applicable, are true and correct in all material respects as of the date thereof.

  • Lessor’s Representations and Warranties Lessor represents and warrants that it will abide by and conform to all such laws, governmental and airport orders, rules and regulations, as shall from time to time be in effect relating in any way to the operation and use of the Aircraft pursuant to this Agreement.

  • Seller’s Representations and Warranties Seller represents and warrants to Purchaser that:

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!