Metering Accuracy Sample Clauses

Metering Accuracy. 1. The accuracy of the Primary Meters, Xxxx’x Xxxx Meters and Gas Analysis Equipment is described in Table 1. Concerning Interconnection Point and Fuel Gas energy flow rate, it is expressed in relation to the maximum rate of gas flow that the meters may accommodate.
Sample 1Sample 2Sample 3See All (4)
AutoNDA by SimpleDocs
Metering Accuracy. If the Meters are registering but their accuracy is outside the limits established in ANSI C12.1, Buyer shall repair and recalibrate or replace the Meters and Buyer shall adjust payments to Supplier for the Delivered Amount for the lesser of the period in which the inaccuracy existed or ninety (90) days. If the period in which the inaccuracy existed cannot be determined, adjusted payments shall be made for a period equal to one-half of the elapsed time since the latest prior test and calibration of the Meters; however, the adjustment period shall not exceed ninety (90) days. If adjusted payments are required, Supplier shall render a statement describing the adjustments to Buyer within thirty (30) days of the date on which the inaccuracy was rectified. Additional payments to Supplier by Buyer shall be made within thirty (30) days of receipt of Supplier's statement. Any payments due Buyer pursuant to this Section shall accompany Supplier's statement.
Sample 1Sample 2See All (4)
Metering Accuracy. The tariff metering scheme shall have an overall accuracy of ± 0.2 % for watt-hour metering. In summary the Metering System reading accuracies are to be within the tolerances set out below: Net Energy Output (kWh) meters ± 0.2% Net Energy Output (kVARh) meters ± 0.5% Capacity (MW) meters ± 0.2% Instrument Transformers Calibration data shall be provided for each instrument transformer, which should result in a negligible overall error ± 0.2% Time Reference 3 seconds per week - maximum
Sample 1
Metering Accuracy. ‌ Accurate reporting of input power (power factor, input current, input current harmonics and voltage) and output power (output current and voltage) readings shall be reported via communication system at all rated voltage. The accuracy shall be maintained across the operating temperature range and between 200Vac and 305Vac. parameter Load Accuracy AC input power <10% ±25W 10-20% <± 5% 20-100% < ±3% AC input current <10% ±0.5A 10-20% < ±2% 20-100% < ±1% AC input current THD <10% ±10% 10-20% ±2% 20-100% ±1% Power factor <10% ±0.1 10-20% ±0.02 20-100% ±0.01 AC input voltage 0-100% ±1% output voltage 0-100% ±0.5% output current 0-100% ±1% output power <10% ±25W 10-20% <3% 20-100% <2%
Sample 1
Metering Accuracy. System metering accuracy, as compared to the actual process value, shall be determined from the value read at the principal readout device such as the recorder, totalizer. System requirements shall not preclude any requirements specified herein for individual devices. For systems where the primary measuring device, transmitter, and receiver are furnished under this section, the accuracy’s shall be within the following limits: a. Pressure: 1.0 percent of measured span. b. Level: 1.0 percent of measured span. c. Temperature: 1.0 percent of measured span. d. Position: 2.0 percent maximum travel.
Sample 1
Metering Accuracy. 1. The accuracy of the Flow Measurement Equipment, Xxxx’x Xxxx Meters and Gas Analysis Equipment is described in Table 1. Concerning Interconnection Point and Fuel Gas energy flow rate, it is expressed in relation to the maximum rate of gas flow that the meters may accommodate. Flow Measurement Equipment Volume Flow Rate Nm³/hour 86,765 to 4,000,000 +/-0.96% Flow Measurement Equipment Energy Flow Rate MJ/hour 3,375,139 to 180,000,000 +/-1.0% Xxxx’x Xxxx Gas Volume Flow Rate Sm³/hour 0 to 2,333,333 +/-5.0% Xxxx’x Xxxx Gas Energy Flow Rate MJ/hour 0 to 104,066,666 +/-5.0% Offtake Pressure Flow Measurement Equipment xxxx 0 to 80 +/-0.16 Gross Calorific Value MJ/Nm³ MJ/Sm³ 36.9 to 47.5 35.0 to 45.0 +/-0.05 +/-0.05 Xxxxx Index MJ/Nm³ MJ/Sm³ 47.5 to 56.2 45.0 to 53.3 +/-0.06 +/-0.06 Offtake Temperature °C -10 to 45 +/-0.25 Hydrocarbon Dewpoint °C Water Dewpoint °C -50 to 15 +/-2.0 Oxygen ppm vol <5000 0 to 25 ppm range at 10 ppm, +/-2.0. 25 to 5000 ppm range at 2000 ppm, +/-50.0
Sample 1

Related to Metering Accuracy

  • Data Accuracy The Custodian has no responsibility for, or duty to review, verify or otherwise perform any investigation as to the completeness, accuracy or sufficiency of, any data or information provided by or on behalf of the Client, any persons authorized by the Client, any Third Party Agent, any Market Participant or any Authorized Data Sources, except to the extent the Custodian has agreed in writing to perform reconciliations, variance or tolerance checks or other specific forms of data review under this Agreement.

  • Preserve Accuracy of Representations and Warranties Each party hereto will refrain from taking any action which would render any of its representations and warranties contained in this Agreement untrue, inaccurate or misleading as of Closing and the Effective Time. Through Closing, each party will promptly notify the other parties of any lawsuit, claim, audit, investigation, administrative action or other proceeding asserted or commenced against such party that may involve or relate in any way to another party to this Agreement. Each party hereto will promptly notify the other parties of any facts or circumstances that come to its attention and that cause, or through the passage of time may cause, any of a party's representations, warranties or covenants to be untrue or misleading at any time from the date hereof through Closing.

  • Accuracy of the Company’s Representations and Warranties Each of the representations and warranties of the Company in this Agreement and the other Transaction Documents that are qualified by materiality or by reference to any Material Adverse Effect shall be true and correct in all respects, and all other representations and warranties shall be true and correct in all material respects, as of the date when made and as of the Closing Date as though made at that time, except for representations and warranties that are expressly made as of a particular date, which shall be true and correct in all respects as of such date.

  • Accuracy of Representations and Warranties; Performance of Covenants At the Closing Time, the representations and warranties contained herein or in certificates of any officer of the Company or any of its subsidiaries (including the Bank) delivered pursuant to the provisions hereof, shall be true and correct, when made, and at the Closing Time, and the Company shall have performed its covenants and other obligations hereunder.

  • Accuracy of Representations and Warranties The representations and warranties of Purchaser contained in this Agreement shall have been true in all material respects on the date hereof and shall be true in all material respects on and as of the Closing Date with the same force and effect as though made on and as of the Closing Date.

  • Representations and Warranties Accurate All representations and warranties of Buyer contained in this Agreement shall be true and accurate in all material respects on and as of the Closing Date as if made again at and as of such date.

  • Accuracy of Representations and Performance of Covenants The representations and warranties made by the Company in this Agreement were true when made and shall be true as of the Closing Date (except for changes therein permitted by this Agreement) with the same force and effect as if such representations and warranties were made at and as of the Closing Date. Additionally, the Company shall have performed and complied with all covenants and conditions required by this Agreement to be performed or complied with by the Company.

  • Minimum Condition and Warranty Requirements for TIPS Sales All goods quoted or sold through a TIPS Sale shall be new unless clearly stated otherwise in writing. All new goods and services shall include the applicable manufacturers minimum standard warranty unless otherwise agreed to in the Supplemental Agreement.

  • Accuracy of the Purchaser’s Representations and Warranties The representations and warranties of each Purchaser shall be true and correct in all material respects as of the date when made and as of the Closing Date as though made at that time, except for representations and warranties that are expressly made as of a particular date, which shall be true and correct in all material respects as of such date.

  • Accuracy of the Investor’s Representations and Warranties The representations and warranties of the Investor shall be true and correct in all material respects.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!