Particular Specifications. Refer to the Variations and Additions to the Standard SANS 1200 Specifications: General, Civil and Structural Works in Annex C3.6. OHS HEALTH AND SAFETY SPECIFICATION PE CONSTRUCTION ENVIRONMENTAL MANAGEMENT PLAN
Particular Specifications. 7.1. Requirements as to shape and dimensions
7.1.1. Shape and dimensions of the triangle (see Annex 3)
7.1.1.1. The theoretical sides of the triangle shall be 500 ± 50 mm long.
7.1.1.2. In the case of an advance warning triangle of type 1, the retro-reflecting units shall be arranged along the edge within a strip of an unvarying width which shall be between 25 mm and 50 mm. In the case of an advance warning triangle of type 2 with fluorescent retro-reflecting material, the unvarying width shall be between 50 mm and 85 mm.
Particular Specifications. In addition to the general specifications prescribed in paragraph 5.2, the device to prevent unauthorized use shall meet the particular conditions prescribed below:
5.3.1. Devices to prevent unauthorized use acting on the steering
5.3.1.1. A device to prevent unauthorized use acting on the steering shall render the steering inoperative. Before the engine can be started, the normal steering operation must be restored.
5.3.1.2. When the device to prevent unauthorized use is set to act, it shall not be possible to prevent the device from functioning.
5.3.1.3. The device to prevent unauthorized use must continue to meet the requirements of paragraphs 5.2.11., 5.3.1.1., 5.3.1.2. and 5.3.1.4. after it has undergone 2,500 locking cycles in each direction of the wear producing test specified in Part 1 of Annex 4 to this Regulation.
5.3.1.4. The device to prevent unauthorized use shall, in its activated position, satisfy one of the following criteria:
5.3.1.4.1. It shall be strong enough to withstand, without damage to the steering mechanism likely to compromise safety, the application of a torque of 300 Nm about the axis of the steering spindle in both directions under static conditions.
5.3.1.4.2. It shall incorporate a mechanism designed to yield or slip, such that the system will withstand, either continuously or intermittently, the application of a torque of at least 100 Nm. The locking system must still withstand the application of this torque after the test specified in Part 2 of Annex 4 to this Regulation.
5.3.1.4.3. It shall incorporate a mechanism designed to permit the steering wheel to rotate freely on the blocked steering spindle. The blocking mechanism shall be strong enough to withstand the application of a torque of 200 Nm about the axis of the steering spindle in both directions under static conditions.
5.3.1.5. If the device to prevent unauthorized use is such that the key can be removed in a position other than the position in which the steering is inoperative, it shall be so designed that the manoeuvre required to reach that position and remove the key cannot be effected inadvertently.
5.3.1.6. If a component fails such that the torque requirements specified in paragraphs 5.3.1.4.1., 5.3.1.4.2. and 5.3.1.4.3. cannot be easily applied, yet the steering system remains blocked, the system shall satisfy the requirements.
5.3.2. Devices to prevent unauthorized use by acting on the transmission or on brakes.
5.3.2.1. A device to prevent unauthorized u...
Particular Specifications. 7.1. Provisions applicable to the assembled restraint
7.1.1. Resistance to corrosion
7.1.1.1. A complete child restraint, or the parts thereof that are liable to corrosion, shall be subject to the corrosion test specified in paragraph 8.1.1. below.
7.1.1.2. After the corrosion test as prescribed in paragraphs 8.1.1.1. and 8.1.1.2., no signs of deterioration likely to impair the proper functioning of the child restraint, and no significant corrosion, shall be visible to the unaided eye of a qualified observer.
Particular Specifications. Refer to Annex C3.3.1.
Particular Specifications. This specification shall be read in conjunction with the following specifications:- SANS 1507 : Electrical cables with extruded solid dielectric insulation for fixed installations SANS 10142-1 : The wiring of premises Part 1 – Low Voltage installations SABS 1213: Mechanical Cable Glands VDE 0278 : Electric cables - Accessories - Material characterisation G01: PARTICULAR SPECIFICATION FOR COLOUR CODES G02: PARTICULAR SPECIFICATION FOR CORROSION PROTECTION E02: ELECTRICAL CABLE RACKS E03: ISOLATOR PUSHBUTTON STATIONS E04: MOTOR CONTROL CENTRES E05: ELECTRICAL LOW VOLTAGE POWER AND CONTROL CABLES E07: ELECTRICAL INDUSTRIAL WELDING PLUGS, COUPLERS AND SOCKET OUTLETS E08: WIRING
Particular Specifications
