Physical Substrate Toolbar Sample Clauses

Open Split View

Download

Share

Cite

Physical Substrate Toolbar. There is a context specific menu for physical substrate as well as a context specific toolbar (Fig. 2‐14).

Sample 1

Save

Copy

Related to Physical Substrate Toolbar

• Physical Architecture 59.2.1 CenturyLink's network architecture in any given local exchange area and/or LATA can vary markedly from another local exchange area/LATA. Using one or more of the NIMs herein, the Parties will agree to a physical architecture plan for a specific LATA, or if appropriate based on other requirements in Section 59, Local Calling Area. The physical architecture plan, as described in the Local Interconnection POI Profile, will be discussed during joint implementation planning. CLEC and CenturyLink agree to Interconnect their networks through existing and/or new Interconnection Facilities between CLEC switch(es) and CenturyLink's End Office Switch(es) and/or Tandem Switch(es). The physical architecture plan will be in accordance with Forecasting and Planning requirements in Article IV.

• Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract.

• Preservative-treated Wood Containing Arsenic Contractor may not purchase preservative-treated wood products containing arsenic in the performance of this Agreement unless an exemption from the requirements of Chapter 13 of the San Francisco Environment Code is obtained from the Department of the Environment under Section 1304 of the Code. The term “preservative-treated wood containing arsenic” shall mean wood treated with a preservative that contains arsenic, elemental arsenic, or an arsenic copper combination, including, but not limited to, chromated copper arsenate preservative, ammoniacal copper zinc arsenate preservative, or ammoniacal copper arsenate preservative. Contractor may purchase preservative-treated wood products on the list of environmentally preferable alternatives prepared and adopted by the Department of the Environment. This provision does not preclude Contractor from purchasing preservative-treated wood containing arsenic for saltwater immersion. The term “saltwater immersion” shall mean a pressure-treated wood that is used for construction purposes or facilities that are partially or totally immersed in saltwater.

• ODUF Physical File Characteristics 6.2.1 ODUF will be distributed to Image Access via Secure File Transfer Protocol (FTP). The ODUF feed will be a variable block format. The data on the ODUF feed will be in a non-compacted EMI format (one hundred seventy-five (175) byte format plus modules). It will be created on a daily basis Monday through Friday except holidays. Details such as dataset name and delivery schedule will be addressed during negotiations of the distribution medium. There will be a maximum of one (1) dataset per workday per OCN. If BellSouth determines the Secure FTP Mailbox is nearing capacity levels, BellSouth may move the customer to CONNECT:Direct file delivery.

• Physical Plant The Board of Supervisors agrees to provide, subject to the budgetary and fiscal provisions of the Charter, the following physical equipment and work environment for users of video display equipment:

• REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.

• 252 Physical Change (a) Forest Service shall adjust the Specified Road construction cost if, prior to acceptance under B6.36, a physical change, caused by a single event and not due to negligence of Purchaser, results in an increase or decrease in work and/or materials furnished by Purchaser involving additional estimated cost of:

• Physical Access PROVIDER agrees to allow the Office of Early Learning and COALITION staff or sub-contractors immediate access to the facilities and spaces used to offer the VPK Program during normal business hours.

• REPAIRED OR REPLACED PRODUCTS, PARTS, OR COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including warranties, as set forth in the Warranties clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturers’ installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.

• Physical Facilities The parties acknowledge the importance of RMOs having quality facilities to enable RMOs an opportunity to rest, discuss clinical matters with other RMOs, and to study. The DHBs acknowledge the importance of private RMO rooms and accept they need to be appropriate for the circumstances. Ideally RMO facilities should be of an appropriate size, secure and have the following: • Kitchen facilities and lounge area, with natural light where possible. • Sufficient number of telephone lines to enable appropriate clinical response by RMOs to pagers and clinical duties. • A study area including sufficient desk space and adequate lighting to enable reading. • Good IT facilities including: inter and intranet access. • Access to relevant clinical material such as lab and x-ray results, up to date etc. • Access and ability to print. • Lockers if secure facilities are not provided elsewhere closer to work spaces. • Sufficient beds for those on nights. • Changing, toilet and shower facilities. • The room(s) and associated facilities should be located close to the hospital’s acute area(s) and serviced regularly with linen supplied. • Where space is available, safe and secure parking close to the main entrance of the hospital for RMOs undertaking work during the hours of darkness. Where space is not available the DHB must make appropriate alternative arrangements such as the provision of taxis. This clause does not require DHBs to retrofit existing facilities to meet such requirements; however DHBs must consider the above requirements when undertaking refurbishment work and when building new hospitals/facilities. Best endeavours should be applied to provide the above within existing facilities in the absence of rebuilding.