Stability criteria Sample Clauses

Stability criteria. 5.3.1. The criteria, using the corresponding annex (3 or 4) to this Regulation, must fulfil one of the following conditions, subject to paragraph 0.0.0.:
Sample 1Sample 2
AutoNDA by SimpleDocs
Stability criteria. To evaluate the influence of operating conditions on the cell/stack performance, a certain degree of stability of both TIPs and TOPs is required. One simple option to evaluate stability is to record a parameter with a desired sampling rate for a desired sampling duration. The parameter is considered stable if the maximum variation (difference between the maximum value and the minimum value recorded) does not exceed a pre-defined threshold value. However, it is difficult to give a generic definition of the sampling rate, sampling duration and variation threshold. This is due to the fact that each individual TIP may have a different impact on the cell/stack performance. If the cell/stack performance is not so sensitive to a TIP, it is then acceptable to set a larger variation threshold for that TIP. A parameter sensitivity investigation needs thus to be performed to define precisely the stability criteria. In addition, the measurement uncertainty of TOPs should also be taken into account for the definition of stability criteria. Furthermore, in many cases a compromise needs to be found between good stability and reasonable test duration. A very strict stability criterion may not be fulfilled due to the time constraint. Nevertheless, the following stability criteria in Table 3 can be taken as a reference and can be adapted according to the test object, test system and test objective. Table 3: Stability criteria for TIPs and TOPs as a reference. Parameter Sampling rate Sampling duration Variation threshold Vcell, VRU,i 1 Hz 3 min 5 mV (SOFC mode) 10 mV (SOEC mode) I 1 Hz 3 min 0.5 A T 1 Hz 3 min 1 K fneg/pos, in/out 1 Hz 3 min 3% FS pneg/pos, in/out 1 Hz 3 min 3% FS
Sample 1Sample 2

Related to Stability criteria

  • Eligibility Criteria (i) Employees covered by this clause will be those who are unable to perform the range of duties to the competence level required within the class of work for which the employee is engaged under this Agreement, because of the effects of a disability on their productive capacity and who meet the impairment criteria for receipt of a Disability Support Pension.

  • General Criteria a) Approved varieties shall be those varieties recommended by the Department, the Corporation, or those listed in the Atlantic Provinces Field Crop Guide, Publication 100A.

  • Origin Criteria For the goods that meet the origin criteria, the exporter should indicate in Box 8 of this Form, the origin criteria met, in the manner shown in the following table: Circumstances of production or manufacture in the country named in Box 11 of this form: Insert in Box 8

  • Evaluation Criteria 5.2.1. The responses will be evaluated based on the following: (edit evaluation criteria below as appropriate for your project)

  • Service Eligibility Criteria 4.3.4.1 High capacity EELs must comply with the following service eligibility requirements:

  • Criteria (1) Annual Evaluation Criteria. All performance evaluations shall be based upon assigned duties, and shall carefully consider the nature of the assignment in terms, where applicable, of:

  • Selection Criteria Each Contract is secured by a new or used Motorcycle. No Contract has a Contract Rate less than 1.00%. Each Contract amortizes the amount financed over an original term no greater than 84 months (excluding periods of deferral of first payment). Each Contract has a Principal Balance of at least $500.00 as of the Cutoff Date.

  • Exclusion Criteria Subjects fulfilling any of the following criteria are not eligible for participation in this study.

  • Design Criteria The Engineer shall develop the roadway design criteria based on the controlling factors specified by the State (i.e. 4R, 3R, 2R, or special facilities), by use of the funding categories, design speed, functional classification, roadway class and any other set criteria as set forth in PS&E Preparation Manual, Roadway Design Manual, Bridge Design Manual, Hydraulic Design Manual, and other deemed necessary State approved manuals. In addition, the Engineer shall prepare the Design Summary Report (DSR) and submit it electronically. The Engineer shall obtain written concurrence from the State prior to proceeding with a design if any questions arise during the design process regarding the applicability of State’s design criteria.

  • Promotional Criteria Subject to the utilisation of the skills, as required by the Employer, an employee remains at this level until he/she has developed the skills to allow the employee to effectively perform the tasks required of this function and is assessed to be competent to perform effectively at a higher level or has successfully completed appropriate training to ASF level 1 and has the demonstrated skills to perform at a higher level. An employee must be prepared to undertake appropriate training. LEVEL 3

Time is Money Join Law Insider Premium to draft better contracts faster.