Design Criteria and Standards All PROJECTS/SERVICES shall be performed in accordance with instructions, criteria and standards set forth by the DIRECTOR.
OMB Standards Unless specified otherwise within this agreement, the Subrecipient shall procure all materials, property, or services in accordance with the requirements of 24 CFR 84.40−48.
Referenced Standards This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of a listed document, the requirements of this Section shall prevail. Reference Title ANSI B16.5
WORKLOAD STANDARDS One (1) Direct Service Hour (DSH) will be equal to sixty (60) minutes of direct services.
REPORT STANDARDS Reports or written material prepared by the Contractor in response to the requirements of this Contract or request of the Project Officer shall, unless otherwise provided for in the Contract, meet standards of professional writing established for the type of report or written material provided, shall be thoroughly researched for accuracy of content, shall be grammatically correct and not contain spelling errors, shall be submitted in a format approved in advance by the Project Officer, and shall be submitted for advance review and comment by the Project Officer. The cost of correcting grammatical errors, correcting report data, or other revisions required to bring the report or written material into compliance with these requirements shall be borne by the Contractor. When submitting documents to APS, The Contractor shall comply with the following guidelines: All submittals and copies shall be printed on at least thirty percent (30%) recycled-content and/or tree-free paper; All submittals must be in the required tabular format in a binder. Report covers / binders shall be recyclable, made from recycled materials, and/or easily removable to allow for recycling of report pages (reports with glued bindings that meet all other requirements are acceptable); The use of plastic covers or dividers should be avoided; and Unnecessary attachments or documents not specifically asked for should not be submitted, and superfluous use of paper should be avoided.
Development Standards 9.1 Developer shall comply with the requirements contained in the Annexation Agreement and any other duly executed agreement related to the Property, except as specifically amended by this Agreement.
Content Standards You agree that you will not upload or provide content or otherwise post, transmit, distribute, or disseminate through the Zelle® Payment Service any material that: (1) is false, misleading, unlawful, obscene, indecent, lewd, pornographic, defamatory, libelous, threatening, harassing, hateful, abusive, or inflammatory; (2) encourages conduct that would be considered a criminal offense or gives rise to civil liability; (3) breaches or infringes any duty toward or rights of any person or entity, including rights of publicity, privacy or intellectual property; (4) contains corrupted data or any other harmful, disruptive, or destructive files; (5) advertises products or services competitive with Zelle®, as determined by Zelle® in its sole discretion; or (6) in Zelle®’s or our sole judgment, is objectionable, restricts or inhibits any person or entity from using or enjoying any portion of the Zelle® Payment Service, or which may expose us, Zelle® or our respective affiliates or customers to harm or liability of any nature.
Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
ENVIRONMENTAL PROTECTION STANDARDS CONTRACTOR shall be in compliance with the Clean Air Act (Title 42 USC Section 7401 et seq.), the Clean Water Act (Title 33 USC Section 1251 et seq.), Executive Order 11738 and Environmental Protection Agency, hereinafter referred to as “EPA,” regulations (Title 40 CFR), as any may now exist or be hereafter amended. Under these laws and regulations, CONTRACTOR assures that:
