Common use of Unbundled Sub-Loop Concentration System (USLC Clause in Contracts

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant Board’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant Board’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant Board’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Board’s collocation space within the SWC that serves the RT where Frankfort Plant Board’s sub- loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 In these scenarios Frankfort Plant Board would be required to place a cross-box, RT, or other similar device and deliver a cable to the BellSouth remote terminal. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant Board’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.6.6.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board Centennial with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardCentennial’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.6.6.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardCentennial’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardCentennial’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.6.6.3 In these scenarios Frankfort Plant Board Centennial would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminal. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardCentennial’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board LS-One with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardLS-One’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardLS-One’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardLS-One’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board LS-One would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminalRT. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardLS-One’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board Sail NetWorks with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardSail NetWorks’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardSail NetWorks’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardSail NetWorks’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board Sail NetWorks would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminal. This cable would be connected, by a BellSouth technician, to a cross-cross- connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardSail NetWorks’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board Broadslate with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardBroadslate’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardBroadslate’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardBroadslate’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board Broadslate would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminalRT. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardBroadslate’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board Momentum Business Solutions with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant Board’s Momentum Business Solutions’ collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant Board’s sub-Momentum Business Solutions’ sub- loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant Board’s Momentum Business Solutions’ sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board Momentum Business Solutions would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminal. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant Board’s Momentum Business Solutions’ sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board E-Tel with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardE-Tel’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardE-Tel’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardE-Tel’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board E-Tel would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminalRT. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardE-Tel’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.

Unbundled Sub-Loop Concentration System (USLC. 2.5.2.1 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide to Frankfort Plant Board Xxxx Communications with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into Frankfort Plant BoardXxxx Communications’s collocation space. TR-008 and TR303 interface standards are available. 2.5.2.2 2.9.2 USLC, using the Lucent Series 5 equipment, will be offered in two different systems. System A will allow up to 96 of Frankfort Plant BoardXxxx Communications’s sub-loops to be concentrated onto multiple DS1s. System B will allow an additional 96 of Frankfort Plant BoardXxxx Communications’s sub-loops to be concentrated onto multiple DS1s. One System A may be supplemented with one System B and they both must be physically located in a single Series 5 dual channel bank. A minimum of two DS1s is required for each system (i.e., System A requires two DS1s and System B would require an additional two DS1s or four in total). The DS1 level facility that connects the RT site with the serving wire center is known as a Feeder Interface. All DS1 Feeder Interfaces will terminate to Frankfort Plant Boardthe CLEC’s collocation space within the SWC that serves the RT where Frankfort Plant Boardthe CLEC’s sub- sub-loops are connected. USLC service is offered with or without concentration and with or without a protection DS1. 2.5.2.3 2.9.3 In these scenarios Frankfort Plant Board Xxxx Communications would be required to place a cross-box, remote terminal (RT), or other similar device and deliver a cable to the BellSouth remote terminalRT. This cable would be connected, by a BellSouth technician, to a cross-connect panel within the BellSouth RT/cross-box and would allow Frankfort Plant BoardXxxx Communications’s sub-loops to then be placed on the ULSC and transported to their collocation space at a DS1 level.