Common use of Unbundled Subloop Distribution Clause in Contracts

Unbundled Subloop Distribution. 2.8.2.1 The USLD facility isa dedicated transmissionfacility that AT&Tprovides from a customer’s point of demarcation to an AT&T cross-connect device. The AT&T cross-connect device may be located within a remote terminal (RT) or a stand-alone cross-box in the field or in the equipment room of a building. The USLD media is a copper twisted pair that can be provisioned as a 2-wire or 4-wire facility. AT&Twill make available the followinsgubloop distribuiton offerings wheer facilities exist: USLD – Voice Grade (USLD-VG) Unbundled Copper Subloop (UCSL) USLD – Intrabuilding Network Cable (USLD-INC (aka riser cable)) 2.8.2.2 USLD-VG is a copper subloop facilitfyrom the cross-box in the fiedlup to and including the point of demarcation at the customer’s premises and may have load coils. 2.8.2.3 UCSL is a copper facilityeighteen thousand (18,000) feet or lesins length provided from the cross- box in the field up to and includinghte customer’s point of demarcationI.f available, this facility will not have any intervening equipment such as load coils between the customer and the cross-box. 2.8.2.3.1 If AFS of GA requests a UCSL and it is not available, AFS of GA may request the copper Subloop facility bemodiefid pursuant to the ULM process to remvoe load coils and/orexcessive bridged taps. If load coils and/or excesvsei bridged taps are removedh, te facility will beclassified as a UCSL. 2.8.2.4 USLD-INC is the distribution facility ownedor controlled by AT&T inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility fromthe cross-connect device in the buinldgi equipment room up to and including the point of demarcation at the customer’s premises. 2.8.2.4.1 Upon request for USLD-INC from AFS of GA, AT&wTill install a cross-connetcpanel in the building equipment room for the purpose of accessing USLD-INC pairs from a building equipment room. The cross-connect paneliwll functoi n as a single point of interconnection (SPOI) for USLD-INC and will be accessible by multiplecarriers as space permits. A&TTwill place cross-connect blocks in twenty five (25) pair increments for AFS of GAu’sse on this cross-connecptanel. AFS of GAwill be responsible for connecting itscfailities to the twenty five2(5) pair cross-connect block(s). 2.8.2.5 For access to Voice Grade USLD and UCSL, AFS of GA shall install a cable to the AT&T cross-box pursuant to the terms and conditions for physical collocation for remote sites set forth in Attachment

Unbundled Subloop Distribution. 2.8.2.1 The USLD facility isa is a dedicated transmissionfacility that AT&Tprovides from a AT&T provides froma customer’s point of demarcation to an toa AT&T cross-connect device. The AT&T cross-connect device may be located within a remote terminal (RT) or a stand-alone cross-box in the field or in the equipment room of roomof a building. The USLD media USLDmedia is a copper twisted pair that can be provisioned as a 2-wire or wireor 4-wire facility. AT&Twill AT&T will make available the followinsgubloop distribuiton followingsubloop distribution offerings wheer where facilities exist: USLD – Voice Grade (USLD-VG) Unbundled Copper Subloop (UCSL) USLD – Intrabuilding Network Cable (USLD-INC (aka riser cable)) 2.8.2.2 USLD-VG is a copper subloop facilitfyrom facilityfrom the cross-box in the fiedlup field up to and including the point of demarcation at the customer’s premises and may have load coils. 2.8.2.3 UCSL is a copper facilityeighteen thousand (18,000) feet or lesins xxxxxx length provided from the cross- box in the field up to and includinghte including the customer’s point of demarcationI.f demarcation. If available, this facility will not have any intervening equipment such as load coils between the customer and the cross-box. 2.8.2.3.1 If AFS of GA AIN/Birch requests a UCSL and it is not available, AFS of GA AIN/Birch may request the copper Subloop facility bemodiefid be modified pursuant to the ULM process ULMprocess to remvoe remove load coils and/orexcessive bridged taps. If load coils and/or excesvsei excessive bridged taps are removedhremoved, te the facility will beclassified as a UCSL. 2.8.2.4 USLD-INC is the distribution facility ownedor controlled by AT&T inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility fromthe cross-connect device in the buinldgi buildni g equipment room up roomup to and including the point of demarcation at the customer’s premises. 2.8.2.4.1 Upon request for USLD-INC from AFS of GAfromAIN/Birch, AT&wTill AT&Twill install a cross-connetcpanel connect panel in the building equipment room for the purpose of accessing USLD-INC pairs from a froma building equipment room. The cross-connect paneliwll functoi n panel will function as a single point of interconnection (SPOI) for USLD-INC and will be accessible by multiplecarriers multiple carriers as space permits. A&TTwill AT&T will place cross-connect blocks in twenty five (25) pair increments for AFS of GAu’sse AIN/Xxxxx’x use on this cross-connecptanelconnectpanel. AFS of GAwill AIN/Birch will be responsible for connecting itscfailities its facilities to the twenty five2(5five (25) pair cross-connect block(s). 2.8.2.5 For access to Voice Grade USLD and UCSL, AFS of GA AIN/Birch shall install a cable to the AT&T cross-box pursuant to the terms and conditions for physical collocation for remote sites set forth in Attachment

Unbundled Subloop Distribution. 2.8.2.1 The USLD facility isa dedicated transmissionfacility that AT&Tprovides from a customer’s point of demarcation to an a AT&T cross-connect device. The AT&T cross-connect device may be located within a remote terminal (RT) or a stand-alone cross-box in the field or in the equipment room of a building. The USLD media is a copper twisted pair that can be provisioned as a 2-wire or 4-wire facility. AT&Twill make available the followinsgubloop distribuiton offerings wheer facilities exist: USLD – Voice Grade (USLD-VG) Unbundled Copper Subloop (UCSL) USLD – Intrabuilding Network Cable (USLD-INC (aka riser cable)) 2.8.2.2 USLD-VG is a copper subloop facilitfyrom the cross-box in the fiedlup to and including the point of demarcation at the customer’s premises and may have load coils. 2.8.2.3 UCSL is a copper facilityeighteen thousand (18,000) feet or lesins length provided from the cross- box in the field up to and includinghte customer’s point of demarcationI.f available, this facility will not have any intervening equipment such as load coils between the customer and the cross-box. 2.8.2.3.1 If AFS of GA AIN/Birch requests a UCSL and it is not available, AFS of GA may AIN/Birchmay request the copper Subloop facility bemodiefid pursuant to the ULM process to remvoe load coils and/orexcessive bridged taps. If load coils and/or excesvsei bridged taps are removedh, te facility will beclassified as a UCSL. 2.8.2.4 USLD-INC is the distribution facility ownedor controlled by AT&T inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility fromthe cross-connect device in the buinldgi equipment room up to and including the point of demarcation at the customer’s premises. 2.8.2.4.1 Upon request for USLD-INC from AFS of GAAIN/Birch, AT&wTill install a cross-connetcpanel in the building equipment room for the purpose of accessing USLD-INC pairs from a building equipment room. The cross-connect paneliwll functoi n as a single point of interconnection (SPOI) for USLD-INC and will be accessible by multiplecarriers as space permits. A&TTwill place cross-connect blocks in twenty five (25) pair increments for AFS of GAu’sse AIN/Birchu’sse on this cross-connecptanel. AFS of GAwill AIN/Birch will be responsible for connecting itscfailities to the twenty five2(5) pair cross-connect block(s). 2.8.2.5 For access to Voice Grade USLD and UCSL, AFS of GA AIN/Birch shall install a cable to the AT&T cross-box pursuant to the terms and conditions for physical collocation for remote sites set forth in Attachment

Unbundled Subloop Distribution. 2.8.2.1 The USLD facility isa is a dedicated transmissionfacility transmission facility that AT&Tprovides BellSouth provides from a customer’s point of demarcation to an AT&T a BellSouth cross-connect device. The AT&T BellSouth cross-connect device may be located within a remote terminal (RT) or a stand-alone cross-box in the field or in the equipment room of a building. The USLD media is a copper twisted pair that can be provisioned as a 2-wire or 4-wire facility. AT&Twill BellSouth will make available the followinsgubloop distribuiton following subloop distribution offerings wheer where facilities exist: USLD – Voice Grade (USLD-VG) Unbundled Copper Subloop (UCSL) USLD – Intrabuilding Network Cable (USLD-INC (aka riser cable)) 2.8.2.2 USLD-VG is a copper subloop facilitfyrom facility from the cross-box in the fiedlup field up to and including the point of demarcation at the customer’s premises and may have load coils. 2.8.2.3 UCSL is a copper facilityeighteen facility eighteen thousand (18,000) feet or lesins less in length provided from the cross- cross-box in the field up to and includinghte including the customer’s point of demarcationI.f demarcation. If available, this facility will not have any intervening equipment such as load coils between the customer and the cross-box. 2.8.2.3.1 If AFS of GA VarTec requests a UCSL and it is not available, AFS of GA VarTec may request the copper Subloop facility bemodiefid be modified pursuant to the ULM process to remvoe remove load coils and/orexcessive and/or excessive bridged taps. If load coils and/or excesvsei excessive bridged taps are removedhremoved, te the facility will beclassified be classified as a UCSL. 2.8.2.4 USLD-INC is the distribution facility ownedor owned or controlled by AT&T BellSouth inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility fromthe from the cross-connect device in the buinldgi building equipment room up to and including the point of demarcation at the customer’s premises. 2.8.2.4.1 Upon request for USLD-INC from AFS of GAVarTec, AT&wTill BellSouth will install a cross-connetcpanel connect panel in the building equipment room for the purpose of accessing USLD-INC pairs from a building equipment room. The cross-connect paneliwll functoi n panel will function as a single point of interconnection (SPOI) for USLD-INC and will be accessible by multiplecarriers multiple carriers as space permits. A&TTwill BellSouth will place cross-connect blocks in twenty five (25) pair increments for AFS of GAu’sse VarTec’s use on this cross-connecptanelconnect panel. AFS of GAwill VarTec will be responsible for connecting itscfailities its facilities to the twenty five2(5five (25) pair cross-connect block(s). 2.8.2.5 For access to Voice Grade USLD and UCSL, AFS of GA VarTec shall install a cable to the AT&T BellSouth cross-box pursuant to the terms and conditions for physical collocation for remote sites set forth in AttachmentAttachment 4. This cable would be connected by a BellSouth technician within the BellSouth cross-box during the set-up process. VarTec’s cable pairs can then be connected to BellSouth’s USL within the BellSouth cross-box by the BellSouth technician. 2.8.2.6 Through the SI process, BellSouth will determine whether access to USLs at the location requested by VarTec is technically feasible and whether sufficient capacity exists in the cross-box. If existing capacity is sufficient to meet VarTec’s request, then BellSouth will perform the site set-up as described in the CLEC Information Package, located at BellSouth’s Interconnection Web site. 2.8.2.7 The site set-up must be completed before VarTec can order Subloop pairs. For the site set-up in a BellSouth cross-connect box in the field, BellSouth will perform the necessary work to splice VarTec’s cable into the cross-connect box. For the site set-up inside a building equipment room, BellSouth will perform the necessary work to install the cross-connect panel and the connecting block(s) that will be used to provide access to the requested USLs. 2.8.2.8 Once the site set-up is complete, VarTec will request Subloop pairs through submission of a LSR form to the LCSC. OC is required with USL pair provisioning when VarTec requests reuse of an existing facility, and the OC charge shall be billed in addition to the USL pair rate. For expedite requests by VarTec for Subloop pairs, expedite charges will apply for intervals less than five (5) days. 2.8.2.9 USLs will be provided in accordance with BellSouth’s TR 73600 Unbundled Local Loop Technical Specifications.

Unbundled Subloop Distribution. 2.8.2.1 The USLD facility isa is a dedicated transmissionfacility transmission facility that AT&Tprovides AT&T provides from a customer’s point of demarcation to an AT&T cross-connect device. The AT&T cross-connect device may be located within a remote terminal (RT) or a stand-stand- alone cross-box in the field or in the equipment room of a building. The USLD media is a copper twisted pair that can be provisioned as a 2-wire or 4-wire facility. AT&Twill AT&T will make available the followinsgubloop distribuiton following subloop distribution offerings wheer where facilities exist: USLD – Voice Grade (USLD-VG) Unbundled Copper Subloop (UCSL) USLD – Intrabuilding Network Cable (USLD-INC (aka riser cable)) 2.8.2.2 USLD-VG is a copper subloop facilitfyrom facility from the cross-box in the fiedlup field up to and including the point of demarcation at the customer’s premises and may have load coils. 2.8.2.3 UCSL is a copper facilityeighteen facility eighteen thousand (18,000) feet or lesins less in length provided from the cross- cross-box in the field up to and includinghte including the customer’s point of demarcationI.f demarcation. If available, this facility will not have any intervening equipment such as load coils between the customer and the cross-box. 2.8.2.3.1 If AFS of GA BLC Management requests a UCSL and it is not available, AFS of GA BLC Management may request the copper Subloop facility bemodiefid be modified pursuant to the ULM process to remvoe remove load coils and/orexcessive and/or excessive bridged taps. If load coils and/or excesvsei excessive bridged taps are removedhremoved, te the facility will beclassified be classified as a UCSL. 2.8.2.4 USLD-INC is the distribution facility ownedor owned or controlled by AT&T inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility fromthe from the cross-connect device in the buinldgi building equipment room up to and including the point of demarcation at the customer’s premises. 2.8.2.4.1 Upon request for USLD-INC from AFS of GABLC Management, AT&wTill AT&T will install a cross-connetcpanel cross- connect panel in the building equipment room for the purpose of accessing USLD-USLD- INC pairs from a building equipment room. The cross-connect paneliwll functoi n panel will function as a single point of interconnection (SPOI) for USLD-INC and will be accessible by multiplecarriers multiple carriers as space permits. A&TTwill AT&T will place cross-connect blocks in twenty five (25) pair increments for AFS of GAu’sse BLC Management’s use on this cross-connecptanelconnect panel. AFS of GAwill BLC Management will be responsible for connecting itscfailities its facilities to the twenty five2(5five (25) pair cross-connect block(s). 2.8.2.5 For access to Voice Grade USLD and UCSL, AFS of GA BLC Management shall install a cable to the AT&T cross-box pursuant to the terms and conditions for physical collocation for remote sites set forth in AttachmentAttachment 4. This cable would be connected by an AT&T technician within the AT&T cross-box during the set-up process. BLC Management’s cable pairs can then be connected to AT&T’s USL within the AT&T cross-box by the AT&T technician. 2.8.2.6 Through the SI process, AT&T will determine whether access to USLs at the location requested by BLC Management is technically feasible and whether sufficient capacity exists in the cross-box. If existing capacity is sufficient to meet BLC Management’s request, then AT&T will perform the site set-up as described in the CLEC Information Package, located at AT&T’s Interconnection Web site. 2.8.2.7 The site set-up must be completed before BLC Management can order Subloop pairs. For the site set-up in an AT&T cross-connect box in the field, AT&T will perform the necessary work to splice BLC Management’s cable into the cross- connect box. For the site set-up inside a building equipment room, AT&T will perform the necessary work to install the cross-connect panel and the connecting block(s) that will be used to provide access to the requested USLs. 2.8.2.8 Once the site set-up is complete, BLC Management will request Subloop pairs through submission of a LSR form to the LCSC. OC is required with USL pair provisioning when BLC Management requests reuse of an existing facility, and the OC charge shall be billed in addition to the USL pair rate. For expedite requests by BLC Management for Subloop pairs, expedite charges will apply for intervals less than five (5) days. 2.8.2.9 USLs will be provided in accordance with AT&T’s TR 73600 Unbundled Local Loop Technical Specifications.