Using Asynchronous Autodma
Using Asynchronous Autodma Sample Clauses
Related to Using Asynchronous Autodma
Non-Synchronous Generation The Interconnection Customer shall design its Small Generating Facility to maintain a composite power delivery at continuous rated power output at the high-side of the generator substation at a power factor within the range of 0.95 leading to 0.95 lagging, unless the NYISO or the Transmission Owner in whose Transmission District the Small Generating Facility interconnects has established a different power factor range that applies to all similarly situated non-synchronous generators in the control area or Transmission District (as applicable) on a comparable basis, in accordance with Good Utility Practice. This power factor range standard shall be dynamic and can be met using, for example, power electronics designed to supply this level of reactive capability (taking into account any limitations due to voltage level, real power output, etc.) or fixed and switched capacitors, or a combination of the two. This requirement shall only apply to newly interconnecting non-synchronous generators that have not yet executed a Facilities Study Agreement as of September 21, 2016.
Synchronous Generation The Interconnection Customer shall design its Small Generating Facility to maintain a composite power delivery at continuous rated power output at the Point of Interconnection at a power factor within the range of 0.95 leading to 0.95 lagging, unless the NYISO or the Transmission Owner in whose Transmission District the Small Generating Facility interconnects has established different requirements that apply to all similarly situated generators in the New York Control Area or Transmission District (as applicable) on a comparable basis, in accordance with Good Utility Practice.
Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers. 2.8.3.2 This element will be provided in MDUs and/or Multi-Tenants Units (MTUs) where either Party owns wiring all the way to the End User’s premises. Neither Party will provide this element in locations where the property owner provides its own wiring to the End User’s premises, where a third party owns the wiring to the End User’s premises.
Wire Unbundled DS1 Digital Loop This is a designed 4-wire Loop that is provisioned according to industry standards for DS1 or Primary Rate ISDN services and will come standard with a test point, OC, and a DLR. A DS1 Loop may be provisioned over a variety of loop transmission technologies including copper, HDSL-based technology or fiber optic transport systems. It will include a 4-Wire DS1 Network Interface at the End User’s location.
USE OF NASA NAME AND NASA EMBLEMS A. NASA Name and Initials Partner shall not use "National Aeronautics and Space Administration" or "NASA" in a way that creates the impression that a product or service has the authorization, support, sponsorship, or endorsement of NASA, which does not, in fact, exist. Except for releases under the "Release of General Information to the Public and Media" Article, Partner must submit any proposed public use of the NASA name or initials (including press releases and all promotional and advertising use) to the NASA Associate Administrator for the Office of Communications or designee ("NASA Communications") for review and approval. Approval by NASA Office of Communications shall be based on applicable law and policy governing the use of the NASA name and initials. B. NASA Emblems Use of NASA emblems (i.e., NASA Seal, NASA Insignia, NASA logotype, NASA Program Identifiers, and the NASA Flag) is governed by 14 C.F.R. Part 1221. Partner must submit any proposed use of the emblems to NASA Communications for review and approval.
Xxxxxxx Xxxxxxx Restrictions/Market Abuse Laws The Participant acknowledges that, depending on his or her country, the broker’s country, or the country in which the Shares are listed, the Participant may be subject to xxxxxxx xxxxxxx restrictions and/or market abuse laws in applicable jurisdictions, which may affect his or her ability to accept, acquire, sell, or attempt to sell or otherwise dispose of Shares or rights to Shares (e.g., Restricted Share Units), or rights linked to the value of Shares, during such times as he or she is considered to have “inside information” regarding the Company (as defined by applicable laws or regulations in the applicable jurisdictions, including the United States and the Participant’s country). Local xxxxxxx xxxxxxx laws and regulations may prohibit the cancellation or amendment of orders the Participant placed before possessing inside information. Furthermore, the Participant may be prohibited from (i) disclosing the inside information to any third party, including fellow employees (other than on a “need to know” basis) and (ii) “tipping” third parties or causing them to otherwise buy or sell securities. Any restrictions under these laws or regulations are separate from and in addition to any restrictions that may be imposed under any applicable Company xxxxxxx xxxxxxx policy. The Participant acknowledges that it is his or her responsibility to comply with any applicable restrictions, and the Participant should consult his or her personal advisor on this matter.
Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.
Xxxxxxx Xxxxxxx/Market Abuse Laws You acknowledge that, depending on your country or broker’s country, or the country in which Common Stock is listed, you may be subject to xxxxxxx xxxxxxx restrictions and/or market abuse laws in applicable jurisdictions, which may affect your ability to accept, acquire, sell or attempt to sell, or otherwise dispose of the shares of Common Stock, rights to shares of Common Stock (e.g., RSUs) or rights linked to the value of Common Stock, during such times as you are considered to have “inside information” regarding the Company (as defined by the laws or regulations in applicable jurisdictions, including the United States and your country). Local xxxxxxx xxxxxxx laws and regulations may prohibit the cancellation or amendment of orders you placed before possessing inside information. Furthermore, you may be prohibited from (i) disclosing insider information to any third party, including fellow employees and (ii) “tipping” third parties or causing them to otherwise buy or sell securities. Any restrictions under these laws or regulations are separate from and in addition to any restrictions that may be imposed under any applicable Company xxxxxxx xxxxxxx policy. You acknowledge that it is your responsibility to comply with any applicable restrictions, and you should speak to your personal advisor on this matter.
Your Billing Rights Keep this Document for Future Use
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Xxxx has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Xxxx. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Xxxx (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Xxxx, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Xxxx will then have the option of paying the one-time SC rates to place the Loop.
