Common use of Water Quality Studies Clause in Contracts

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number. f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 1065CE05-E678-4FDA-9A15-CD435C82F2FA f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 77A45C0A-6CA6-4436-AA61-FD6DAA5DDC8C f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number. f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall:: DocuSign Envelope ID: B8DCCCD3-A0B3-4BAD-BC2D-75E46611CBD6 a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number. f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: CB4D4692-3486-4327-9EA0-F7A661B6ACDF f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: AF0A5C71-20F3-481C-96D9-9B6E48645CA8 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: B4E47CBB-54AA-4467-B86B-B1C47B94F45E f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  : 1) the name and date of the Total Maximum Daily Load,  . 2) the name and date of any corresponding Implementation Plan, and  . 3) a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  : 1) that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  and 2) if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge. 3) Discuss the Best Management Practices that will be used-particularly at the discharge point to the water body to meet other water quality regulations, such as vegetative xxxxxx, silt fencing, compliance with the Texas Pollutant Discharge Elimination System (TPDES).

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences Impacts of the Proposed Project section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 4542C97A-A0BF-4F41-B2F5-F020508C38AA f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number. f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  DocuSign Envelope ID: D78C9312-D95C-4FD3-B00A-7CFCC10A2DB4 • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences Impacts of the Proposed Project section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 45A56478-C163-42E7-AE73-4A77A86451FF f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: F9E4AA24-4672-4529-8EFA-00D1CA218520 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences Impacts of the Proposed Project section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 96ECF328-ADFC-48E2-AAEF-44272BE1E265 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: CA9F0A59-74CF-45EC-A0BA-DA5EDEFB2344 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 531A9DDE-2967-4B7D-96AD-B570C85CF1EE f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: D48DDB49-3B26-4601-BF7C-3027905768B1 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 0D2F7E90-5707-4244-B1F8-5FC3612CC484 f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences Impacts of the Proposed Project section of the EA.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number.. DocuSign Envelope ID: 4154F7E6-47C6-48AD-BA70-902BFE5F00DC f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  the name and date of the Total Maximum Daily Load,  the name and date of any corresponding Implementation Plan, and  a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge.

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EAWater Resources Technical Report.) The Engineer shall: a. Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. Identify whether the project drains to any impaired assessment unit. d. Provide the location of the project within the watershed of the impaired assessment unit. e. Identify the impaired assessment unit number, segment name, and segment number. f. Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  • the name and date of the Total Maximum Daily Load,  • the name and date of any corresponding Implementation Plan, and  • a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  DocuSign Envelope ID: 719137B1-7E3D-42BC-8A29-9D6AE732CB6A • that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  • if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge. i. Discuss the Best Management Practices that will be used-particularly at the discharge point to the water body to meet other water quality regulations, such as vegetative xxxxxx, silt fencing, compliance with the Texas Pollutant Discharge Elimination System (TPDES).

Water Quality Studies. (This scope is for the corresponding section(s) as listed in the Affected Environment and Environmental Consequences section of the EA.) The Engineer shall: a. : • Address all water quality studies in accordance with Section 303(d) of the Clean Water Act as administered by the Texas Commission on Environmental Quality (TCEQ). b. . • Identify if the project is located within five miles of an impaired assessment unit and within the watershed of the impaired assessment unit. c. . • Identify whether the project drains to any impaired assessment unit. d. . • Provide the location of the project within the watershed of the impaired assessment unit. e. . • Identify the impaired assessment unit number, segment name, and segment number. f. . • Identify the pollutant(s) in the discharge for which the water body is listed, and the year of the 303(d) list used in the assessment g. assessment • If the impaired assessment unit has a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, provide:  o the name and date of the Total Maximum Daily Load,  o the name and date of any corresponding Implementation Plan, and  o a discussion of whether the project is consistent with the approved Total Maximum Daily Load and Implementation Plan. h. . DocuSign Envelope ID: 5A2DC6EC-64DB-4A02-A984-B96FAAFF8279 • If unit does not have a Total Maximum Daily Load that has been the impaired assessment approved by the Environmental Protection Agency, indicate:  o that the impaired assessment unit does not have a Total Maximum Daily Load that has been approved by the Environmental Protection Agency, and  o if the project could discharge the pollutant identified in (d) above. If yes, discuss measures that will be taken to prevent or reduce the likelihood of such a discharge. • Discuss the Best Management Practices that will be used-particularly at the discharge point to the water body to meet other water quality regulations, such as vegetative xxxxxx, silt fencing, compliance with the Texas Pollutant Discharge Elimination System (TPDES).