When ordering a Local. Switching Element, CLEC may order from Ameritech separate interLATA and intraLATA capabilities (i.e., 2 PICs where available) on a line or trunk basis.
When ordering a Local Sample Clauses
Related to When ordering a Local
Pre-Ordering BellSouth will provide electronic access to its OSS and the information contained therein in order that Freedom can perform the following pre-ordering functions: service address validation, telephone number selection, service and feature availability, due date information, customer record information and loop makeup information. Mechanized access is provided by electronic interfaces whose specifications for access and use are set forth at BellSouth’s Interconnection Web site and are incorporated herein by reference. The process by which BellSouth and Freedom will manage these electronic interfaces to include the development and introduction of new interfaces will be governed by the change Version: 4Q04 Resale Agreement 12/14/04 management process as described in Section 2.6 below. Freedom shall provide to BellSouth access to customer record information, including circuit numbers associated with each telephone number where applicable. Freedom shall provide such information within four (4) hours after request via electronic access where available. If electronic access is not available, Freedom shall provide to BellSouth paper copies of customer record information, including circuit numbers associated with each telephone number where applicable. If BellSouth requests the information before noon, the customer record information shall be provided the same day. If BellSouth requests the information after noon, the customer record information shall be provided by noon the following day.
Maximum order The Contractor is not obligated to honor—
Minimum Order When the Government requires supplies or services covered by this contract in an amount of less than one each, the Government is not obligated to purchase, nor is the Contractor obligated to furnish those supplies or services under the contract.
Ordering 7.4.1 When ordering LIS, the ordering Party shall specify requirements on the Access Service Request (ASR): 1) the type and number of Interconnection facilities to terminate at the Point of Interconnection in the Serving Wire Center; 2) the type of interoffice transport, (i.e., direct trunked transport or tandem switched transport); 3) the number of Ports to be provisioned at an End Office Switch or local Tandem Switch; and 4) any optional features. When the ordering Party requests facilities, routing, or optional features different than those determined to be available, the Parties will work cooperatively in determining an acceptable configuration, based on available facilities, equipment and routing plans.
Labelling and Packaging C17.1 On dispatch of any consignment of the Goods the Contractor shall send the Authority an advice note specifying the means of transport, the place and date of dispatch, the number of packages and their weight and volume. The Goods shall be packed and marked in a proper manner.
METHOD OF ORDERING The County shall issue Delivery Orders against the contract on an as needed basis for the goods or services listed on the Bid Response Form.
Billing and Payment Procedure for Forest Products Delivered The State will compute and forward to Purchaser a billing statement of charges for forest products delivered during the billing period at the delivered rate shown in P- 028.2 clause. After receipt of the billing statement, Purchaser’s payment must be received by the Department of Natural Resources on or before the due date shown on the billing statement. Purchaser agrees to make payment, payable to the Department of Natural Resources. Failure to pay on time for forest products delivered is considered a breach of contract. Included with the billing statement will be a summary report for the billing period compiled by the State or their log and load reporting service. The State will adjust final xxxxxxxx to account for any State approved payment reductions. P-080 Payment Account Refund Advance payments made under P-045 or P-045.2 remaining on account above the value for the charges shall be returned to Purchaser within 30 days following the final report of charges. Refunds not made within the 30 day period will accrue interest at the interest rate, as established by WAC 000-000-000, computed on a daily basis until paid.
Ordering Process 6.4.1 CLEC, or CLEC's agent, shall act as the single point of contact for its End User Customers' service needs, including without limitation, sales, service design, order taking, Provisioning, change orders, training, maintenance, trouble reports, repair, post-sale servicing, Billing, collection and inquiry. CLEC's End User Customers contacting Qwest in error will be instructed to contact CLEC; and Qwest's End User Customers contacting CLEC in error will be instructed to contact Qwest. In responding to calls, neither Party shall make disparaging remarks about each other. To the extent the correct provider can be determined, misdirected calls received by either Party will be referred to the proper provider of local Exchange Service; however, nothing in this Agreement shall be deemed to prohibit Qwest or CLEC from discussing its products and services with CLEC's or Qwest's End User Customers who call the other Party seeking such information.
Stop Work Order (a) NYSERDA may at any time, by written Order to the Contractor, require the Contractor to stop all or any part of the Work called for by this Agreement for a period of up to ninety (90) days after the Stop Work Order is delivered to the Contractor, and for any further period to which the parties may agree. Any such order shall be specifically identified as a Stop Work Order issued pursuant to this Section. Upon receipt of such an Order, the Contractor shall forthwith comply with its terms and take all reasonable steps to minimize the incurrence of costs allocable to the Work covered by the Order during the period of work stoppage consistent with public health and safety. Within a period of ninety (90) days after a Stop Work Order is delivered to the Contractor, or within any extension of that period to which the parties shall have agreed, NYSERDA shall either:
Shipment Dell will ship the APEX System to the Site when included as part of the APEX Service. The terms and process for shipment and delivery of the APEX System will be stated in the applicable Service Offering Description.
