Common use of Working Access to Equipment and Plant Support Activities to be Provided by Owner Clause in Contracts

Working Access to Equipment and Plant Support Activities to be Provided by Owner. The plant support personnel and facilities to be provided by Owner in accordance with Section 14.1(b) are as follows: (i) operations support to establish the required plant conditions for the repairs; (ii) make the plant systems, structures, and components available and placed in the proper configuration; (iii) provide the valve clearances and tag-outs necessary; (iv) provide the necessary licensed operators in the control room and containment as required by the COL; (v) establish and maintain appropriate and acceptable industrial safety conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vi) as appropriate, provide body harnesses and/or personal flotation devices in sufficient quantities such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vii) provide safe scaffolding meeting applicable OSHA standards (as required); (viii) provide suitable ambient lighting; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures (ix) provide free and unobstructed access to the Site, including maintained storage areas and roadways. Floor conditions shall be suitable for crane and truck operation; (x) provide access such as remove/reinstall cubicle plugs and other related plant facilities, such as piping, ductwork, cable trays, platforms, insulation, etc.; (xi) provide logistics support and labor for moving equipment/materials into and out of the plant and shipping; (xii) provide lay down area(s) for equipment storage, set-up, staging and operation. Area requirements shall depend on the scope of services performed; (xiii) provide areas for storage of low specific activity and clean equipment boxes and/or cargo containers. The area(s) shall vary depending on storage configurations and scope of services; (xiv) establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xv) provide anti-contamination clothing, lockers, change area, dosimetry, health physics and radiation protection service and badging for Site access as typically required; (xvi) provide official whole body exposure data for Contractor personnel upon personnel departure from the Site; (xvii) provide Gamma isotopic analysis to determine radioactivity of waste; (xviii) provide breathing air and respiratory protection as necessary; (xix) provide plant compressed air as required; (xx) provide air for ventilation; (xxi) provide 110V, 220V and 480V power as required; (xxii) provide plant and deionized water; (xxiii) make available to Contractor, and maintain in an operable condition those hand tools, special tools, and calibrated equipment necessary; (xxiv) allow access to machine shop and welding facilities, and hot tool crib access, as required; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures (xxv) provide crane operators, including polar crane availability on an as scheduled basis, and any other personnel necessary to complete the tasks outside of Contractor scope; (xxvi) provide for consumables such as wipes and rags, and disposal of all contaminated materials; (xxvii) provide QA/QC coverage as required in the Site approved procedures; and (xxviii) provide outside phone lines, sanitation facilities and drinking water.

Working Access to Equipment and Plant Support Activities to be Provided by Owner. The plant support personnel and facilities to be provided by Owner in accordance with Section 14.1(b) are as follows: (i) operations support to establish the required plant conditions for the repairs; (ii) make the plant systems, structures, and components available and placed in the proper configuration; the COL; (iii) provide the valve clearances and tag-outs necessary; (iv) provide the necessary licensed operators in the control room and containment as required by the COL;by (v) establish and maintain appropriate and acceptable industrial safety conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vi) as appropriate, provide body harnesses and/or personal flotation devices in sufficient quantities such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vii) provide safe scaffolding meeting applicable OSHA standards (as required); (viii) provide suitable ambient lighting; “[**]” in this Exhibit 10.01 10.02 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures. (ix) provide free and unobstructed access to the Site, including maintained storage areas and roadways. Floor conditions shall be suitable for crane and truck operation; (x) provide access such as remove/reinstall cubicle plugs and other related plant facilities, such as piping, ductwork, cable trays, platforms, insulation, etc.; (xi) provide logistics support and labor for moving equipment/materials into and out of the plant and shipping; (xii) provide lay down area(s) for equipment storage, set-up, staging and operation. Area requirements shall depend on the scope of services performed; (xiii) provide areas for storage of low specific activity and clean equipment boxes and/or cargo containers. The area(s) shall vary depending on storage configurations and scope of services; (xiv) establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xv) provide anti-contamination clothing, lockers, change area, dosimetry, health physics and radiation protection service and badging for Site access as typically required; (xvi) provide official whole body exposure data for Contractor personnel upon personnel departure from the Site; (xvii) provide Gamma isotopic analysis to determine radioactivity of waste; (xviii) provide breathing air and respiratory protection as necessary; (xix) provide plant compressed air as required; (xx) provide air for ventilation; (xxi) provide 110V, 220V and 480V power as required; (xxii) provide plant and deionized water; (xxiii) make available to Contractor, and maintain in an operable condition those hand tools, special tools, and calibrated equipment necessary; (xxiv) allow access to machine shop and welding facilities, and hot tool crib access, as required; “[**]” in this Exhibit 10.01 10.02 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures. (xxv) provide crane operators, including polar crane availability on an as scheduled basis, and any other personnel necessary to complete the tasks outside of Contractor scope; (xxvi) provide for consumables such as wipes and rags, and disposal of all contaminated materials; (xxvii) provide QA/QC coverage as required in the Site approved procedures; and (xxviii) provide outside phone lines, sanitation facilities and drinking water.

Working Access to Equipment and Plant Support Activities to be Provided by Owner. The plant support personnel and facilities to be provided by Owner in accordance with Section Sections 14.1(b) and/or 14.2(b) are as follows:listed below. Owner shall also provide this support after Unit Mechanical Completion should Contractor be required to repair or replace Equipment during the period from the Unit Mechanical Completion through the end of the Warranty Period and also with respect to any period in which Contractor is performing Warranty Work under this Agreement. (i) operations Operations support to establish the required plant conditions (i.e., operating mode) for the repairs; (ii) make Make the plant systems, structures, and components available and placed in the proper configuration; (iii) provide Provide the valve clearances and tag-outs necessary; (iv) provide Provide the necessary licensed operators in the control room and containment as required by the COL; (v) establish Establish and maintain appropriate and acceptable industrial safety conditions in accordance with Laws, Good Industry Practices, and utility Operator policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vi) as As appropriate, provide body harnesses and/or personal flotation devices in sufficient quantities such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vii) provide safe Provide scaffolding and scaffolding materials meeting applicable OSHA standards (as required); (viii) provide suitable Provide reasonable ambient lighting; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures; (ix) provide free and unobstructed Provide reasonable access to the SiteSite and Nearby Work Areas, including maintained storage areas and roadways. Floor , and floor conditions shall be suitable for crane and truck operationoperation to the extent allowed by the Facility design; (x) provide Provide access such as remove/remove and reinstall cubicle plugs and other related plant facilities, such as piping, ductwork, cable trays, platforms, platforms and insulation, etc.; (xi) provide Provide logistics support and labor for moving equipment/equipment and materials into and out of the plant and shippingFacility; (xii) provide Provide lay down area(s) areas for equipment storage, set-up, staging and operation. Area operation (area requirements shall will depend on the scope of services performed); (xiii) provide Provide areas for storage of low specific activity materials, and clean equipment boxes and/or cargo containersSealands. The area(s) shall areas may vary depending on storage configurations and scope of services; (xiv) establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xv) provide Provide anti-contamination clothing, lockers, change area, dosimetry, health physics and radiation protection service and badging for Site access as typically required; (xv) Establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and Operator policy, including, but not limited to, any required decontamination to reasonable limits that will allow Contractor to perform its obligations under this Article 14, such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xvi) provide Dispose appropriately of radioactive materials and waste from the Facility in accordance with applicable Laws and Good Industry Practices; (xvii) Provide official whole body exposure data for Contractor personnel Contractor’s Personnel upon personnel Contractor’s Personnel departure from the Site; (xviixviii) provide Provide Gamma isotopic analysis to determine radioactivity releaseability of Equipment and waste; (xviiixix) provide Provide breathing air and respiratory protection as necessary; (xixxx) provide Provide plant compressed air as required; (xxxxi) provide Provide air for ventilation; (xxixxii) provide Provide 110V, 220V and 480V power as required; (xxiixxiii) provide Provide plant and deionized water; (xxiiixxiv) make Make available to Contractor, and maintain in an operable condition Contractor those hand tools, special tools, and calibrated equipment necessaryas are available on-Site; (xxivxxv) allow Allow Contractor to access to and use machine shop and shop, welding facilities, and hot tool crib accesscrib, as required; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment required and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Proceduresallow Contractor use of associated tradesmen; (xxvxxvi) provide Provide crane operatorsoperators for permanently installed cranes, including polar crane availability on an as scheduled needed basis, and any other personnel necessary to complete the tasks outside of Contractor scope; (xxvixxvii) provide Provide for consumables such as wipes and rags, and disposal of all contaminated materials; (xxviixxviii) provide Provide QA/QC coverage as required in the Site Owner approved proceduresprocedures to the extent such work is performed under the Owner quality assurance program; (xxix) Provide access to existing and available outside phone lines; and (xxviiixxx) provide outside phone lines, Provide sanitation facilities and drinking waterwater as available.

Working Access to Equipment and Plant Support Activities to be Provided by Owner. The plant support personnel and facilities to be provided by Owner in accordance with Section 14.1(b) are as follows: (i) operations support to establish the required plant conditions for the repairs; (ii) make the plant systems, structures, and components available and placed in the proper configuration; (iii) provide the valve clearances and tag-outs necessary; (iv) provide the necessary licensed operators in the control room and containment as required by the COL; (v) establish and maintain appropriate and acceptable industrial safety conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vi) as appropriate, provide body harnesses and/or personal flotation devices in sufficient quantities such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vii) provide safe scaffolding meeting applicable OSHA standards (as required); (viii) provide suitable ambient lighting; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures; (ix) provide free and unobstructed access to the Site, including maintained storage areas and roadways. Floor conditions shall be suitable for crane and truck operation; (x) provide access such as remove/reinstall cubicle plugs and other related plant facilities, such as piping, ductwork, cable trays, platforms, insulation, etc.; (xi) provide logistics support and labor for moving equipment/materials into and out of the plant and shipping; (xii) provide lay down area(s) for equipment storage, set-up, staging and operation. Area requirements shall depend on the scope of services performed; (xiii) provide areas for storage of low specific activity and clean equipment boxes and/or cargo containers. The area(s) shall vary depending on storage configurations and scope of services; (xiv) establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xv) provide anti-contamination clothing, lockers, change area, dosimetry, health physics and radiation protection service and badging for Site access as typically required; (xvi) provide official whole body exposure data for Contractor personnel upon personnel departure from the Site; (xvii) provide Gamma isotopic analysis to determine radioactivity of waste; (xviii) provide breathing air and respiratory protection as necessary; (xix) provide plant compressed air as required; (xx) provide air for ventilation; (xxi) provide 110V, 220V and 480V power as required; (xxii) provide plant and deionized water; (xxiii) make available to Contractor, and maintain in an operable condition those hand tools, special tools, and calibrated equipment necessary; (xxiv) allow access to machine shop and welding facilities, and hot tool crib access, as required; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures; (xxv) provide crane operators, including polar crane availability on an as scheduled basis, and any other personnel necessary to complete the tasks outside of Contractor scope; (xxvi) provide for consumables such as wipes and rags, and disposal of all contaminated materials; (xxvii) provide QA/QC coverage as required in the Site approved procedures; andand water. (xxviii) provide outside phone lines, sanitation facilities and drinking water.drinking

Working Access to Equipment and Plant Support Activities to be Provided by Owner. The plant support personnel and facilities to be provided by Owner in accordance with Section 14.1(b) are as follows: (i) operations support to establish the required plant conditions for the repairs; (ii) make the plant systems, structures, and components available and placed in the proper configuration; (iii) provide the valve clearances and tag-outs necessary; (iv) provide the necessary licensed operators in the control room and containment as required by the COL; (v) establish and maintain appropriate and acceptable industrial safety conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vi) as appropriate, provide body harnesses and/or personal flotation devices in sufficient quantities such that reasonably unencumbered access to the required work areas is enabled for all personnel; (vii) provide safe scaffolding meeting applicable OSHA standards (as required); (viii) provide suitable ambient lighting; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures; (ix) provide free and unobstructed access to the Site, including maintained storage areas and roadways. Floor conditions shall be suitable for crane and truck operation; (x) provide access such as remove/reinstall cubicle plugs and other related plant facilities, such as piping, ductwork, cable trays, platforms, insulation, etc.; (xi) provide logistics support and labor for moving equipment/materials into and out of the plant and shipping; (xii) provide lay down area(s) for equipment storage, set-up, staging and operation. Area requirements shall depend on the scope of services performed; (xiii) provide areas for storage of low specific activity and clean equipment boxes and/or cargo containers. The area(s) shall vary depending on storage configurations and scope of services; (xiv) establish and maintain appropriate and acceptable radiological conditions in accordance with Laws, Good Industry Practices, and utility policy such that reasonably unencumbered access to the required work areas is enabled for all personnel; (xv) provide anti-contamination clothing, lockers, change area, dosimetry, health physics and radiation protection service and badging for Site access as typically required; (xvi) provide official whole body exposure data for Contractor personnel upon personnel departure from the Site; (xvii) provide Gamma isotopic analysis to determine radioactivity of waste; (xviii) provide breathing air and respiratory protection as necessary; (xix) provide plant compressed air as required; (xx) provide air for ventilation; (xxi) provide 110V, 220V and 480V power as required; (xxii) provide plant and deionized water; (xxiii) make available to Contractor, and maintain in an operable condition those hand tools, special tools, and calibrated equipment necessary; (xxiv) allow access to machine shop and welding facilities, and hot tool crib access, as required; “[**]” in this Exhibit 10.01 indicates material that has been omitted pursuant to a request for confidential treatment and filed separately with the Securities and Exchange Commission. Execution Version Confidential Trade Secret Information—Subject to Restricted Procedures; (xxv) provide crane operators, including polar crane availability on an as scheduled basis, and any other personnel necessary to complete the tasks outside of Contractor scope; (xxvi) provide for consumables such as wipes and rags, and disposal of all contaminated materials; (xxvii) provide QA/QC coverage as required in the Site approved procedures; and (xxviii) provide outside phone lines, sanitation facilities and drinking water.