Filling unit definition

Filling unit means a device to allow filling of the container; the filling unit can be realised by integration in the 80 per cent stop valve of the container or by a remote filling unit at the outside of the vehicle.
Filling unit means a device to allow filling of the container; the filling unit can be realised by integration in the 80 per cent stop valve of the container or by a remote filling unit at the outside of the vehicle;

Examples of Filling unit in a sentence

  • Subsequently, it started its commercial production at Filling unit, Crushing unit and Refinery unit in 2002, 2012 & 2017 respectively.

  • Container(s) or cylinder(s)2 Pressure indicator2 Pressure relief valve2 Automatic valve(s)2 Excess flow valve2 Gas-tight housing2 Pressure regulator(s)2 Non-return valve(s)2 Pressure relief device (PRD) (temperature triggered)2 Manual valve2 Flexible fuel lines2 Filling unit or receptacle2 Gas injector(s)2 Gas flow adjuster2 1 Distinguishing number of the country which has granted/extended/refused/withdrawn approval (see approval provisions in the Regulation).

  • The pilot study should identify the general shapes of the test and reference curves, the magnitude of the difference in product profiles, and the noise associated with each blood sampling time (e.g., variability attributable to assay error and the variability between subjects, for parallel study designs, or within subjects, for crossover study designs).

  • The Tenderer should have supplied machinery to the Gudiyattam Match Box Filling unit at Gudiyatham.iii.

  • Address(Decimal) The register content as below changing is relative to single filing unit, when it is used to calibrate volume:Address(Decimal)Note: You need to set register 2000 (Filling unit address) before set register 2007(Restore calibration factor).

  • Filling unit (CM1 line books 2022) After the bottles are filled, they move to the tipping unit where the tips are fed by four shoots of vibratory feeder.

  • Cross-plaintiffs allege that cross-defendants violated the Tennessee Viatical Settlement Act (“TVSA”), Tenn.

  • The hydrogeologic units identified for the area of the Project correspond to the Rock unit and the Filling unit, a short description of these is given below.

  • The rotor brake system includes mainly, Hands pump unit Brake unit and Filling unit.

  • Provision of 400L x 450W x 725Ht Fixed Pedestal of 2 Drawer + 1 Filling unit, made of 18mm thk Pre laminated Particle Board with PVC edge banding.

Related to Filling unit

  • Drilling unit means the area fixed for the drilling of one well by order or rule of any state or federal body having authority. If a Drilling Unit is not fixed by any such rule or order, a Drilling Unit shall be the drilling unit as established by the pattern of drilling in the Contract Area unless fixed by express agreement of the Drilling Parties.

  • Dwelling unit means a single unit providing complete, independent living facilities for one or more persons, including permanent provisions for living, sleeping, eating, cooking and sanitation.

  • Interior of the dwelling unit means the inside of the dwelling unit, consisting of interior walls,

  • Living unit means a room, apartment, cottage, or other area within a facility set aside for the exclusive use or control of one or more identified residents.

  • Accessory dwelling unit means an attached or a detached residential dwelling unit that provides complete independent living facilities for one or more persons and is located on a lot with a proposed or existing primary residence. It shall include permanent provisions for living, sleeping, eating, cooking, and sanitation on the same parcel as the single-family or multifamily dwelling is or will be situated. An accessory dwelling unit also includes the following:

  • INTER-CONNECTION POINT/ DELIVERY/ METERING POINT means a single point at 220kV or above, where the power from the Project(s) is injected into the identified ISTS Substation (including the dedicated transmission line connecting the Projects with the substation system) as specified in the RfS document. Metering shall be done at this interconnection point where the power is injected into. For interconnection with grid and metering, the WPDs shall abide by the relevant CERC/ SERC Regulations, Grid Code and Central Electricity Authority (Installation and Operation of Meters) Regulations, 2006 as amended and revised from time to time.