Mechanical Noise definition

Mechanical Noise means sound produced as a byproduct of the operation of the mechanical components of a WES(s) such as the gearbox and generator.
Sample 1Sample 2

Examples of Mechanical Noise in a sentence

  • Table 1 – Mechanical Noise Emission Objectives Noise emissions from mechanical plant have been assessed against the amenity noise emission objectives.

  • Noise Reduction Techniques – Mechanical Noise (Cont.) • Mount/Foundation • For vibration isolation • Active method : effective to high freq.

  • Article 5: Signs and Outdoor Lighting Section 5.9 Exterior Mechanical Noise Abatement Purpose: Due to the proliferation of mechanical devices associated with and accessory to dwellings, such as, but not exclusively, air conditioners/heat pumps, swimming pool heating and circulating pumps, and electric generators, noise levels as perceived by neighbors and the general public are increasing.

  • Mechanical Noise Equivalent Acceleration (MNEA) is found from equation (4).

  • Meanwhile, analyzed articlesmostly do not apply this or any other comprehensive and systematic approach (Figure 2) to reforming forest governance system in Ukraine and mainly focus on one or few aspects of reform.

Related to Mechanical Noise

  • Mechanical Completion means that (a) all components and systems of the Project have been properly constructed, installed and functionally tested according to EPC Contract requirements in a safe and prudent manner that does not void any equipment or system warranties or violate any permits, approvals or Laws; (b) the Project is ready for testing and commissioning, as applicable; (c) Seller has provided written acceptance to the EPC Contractor of mechanical completion as that term is specifically defined in the EPC Contract.

  • Bulk gasoline plant means a gasoline storage and distribution facility with an average daily throughput of 20,000 gallons (76,000 liters) of gasoline or less on a 30-day rolling average.

  • High global warming potential hydrofluorocarbons means any hydrofluorocarbons in a particular end use for which EPA’s Significant New Alternatives Policy (SNAP) program has identified other acceptable alternatives that have lower global warming potential. The SNAP list of alternatives is found at 40 CFR Part 82 subpart G with supplemental tables of alternatives available at (http://www.epa.gov/snap/).

  • Cyanoacrylate adhesive means any adhesive with a cyanoacrylate content of at least 95% by weight.

  • Mechanical restraint means any device or object used to limit a student’s movement.

  • Temporary Disconnection means an ICP is De-energised but there is no change to the status of the ICP in the Registry;

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Electrical work Means any labor or material used in installing, altering, maintaining, or extending an electrical wiring system and the appurtenances, apparatus, or equipment used in connection with the use of electrical energy in, on, outside, or attached to a building, residence, structure, property, or premises. The term includes service entrance conductors as defined by the National Electrical Code.

  • Temporary clean coal technology demonstration project means a clean coal technology demonstration project that is operated for a period of five years or less and that complies with the SIP and other requirements necessary to attain and maintain the national ambient air quality standards during the project and after the project is terminated.

  • Slug loading means any pollutant, including oxygen demanding pollutants, released in a discharge at a flow rate and/or pollutant concentration as to cause interference in the POTW.

  • Synchronous Optical Network (SONET) is an optical interface standard that allows inter-networking of transmission products from multiple vendors. The base rate is 51.84 Mbps (“OC-1/STS-1”) and higher rates are direct multiples of the base rate, up to 13.22 Gbps.

  • Built-Up Area and/or “Covered Area” in relation to a Flat shall mean the floor area of that Flat including the area of balconies and terraces, if any attached thereto, and also the thickness of the walls (external or internal) and the columns and pillars therein Provided That if any wall, column or pillar be common between two Flats, then one-half of the area under such wall column or pillar shall be included in the built-up area of each such Flat.

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • manoeuvring area means that part of an aerodrome to be used for the take-off, landing and taxiing of aircraft, excluding aprons;

  • Polystyrene foam adhesive means an aerosol adhesive designed to bond polystyrene foam to substrates.

  • Perfluoroalkyl and polyfluoroalkyl substances or “PFAS” means a class of fluorinated organic chemicals containing at least one fully fluorinated carbon atom.

  • Instantaneous flow measurement means the flow measured during the minimum time required for the flow-measuring device or method to produce a result in that instance. To the extent practical, instantaneous flow measurements coincide with the collection of any grab samples required for the same sampling period so that together the samples and flow are representative of the discharge during that sampling period.

  • Apprenticeable occupation means an occupation approved for apprenticeship by the U.S. Department of Labor, Office of Apprenticeship.

  • Taximeter means any device for calculating the fare to be charged in respect of any journey in a hackney carriage or private hire vehicle by reference to the distance travelled or time elapsed since the start of the journey, or a combination of both; and

  • Residual disinfectant concentration (“C” in CT cal- culations) means the concentration of disinfectant measured in mg/l in a representative sample of water.

  • Injection tool means a device used for controlled subsurface injection of radioactive tracer material.

  • Grease interceptor means a watertight device designed to intercept and retain or remove grease and fatty substances. The device may be located inside (grease separator) or outside (grease tank or grease trap) a facility.

  • Flocculation means a process to enhance agglomeration or collection of smaller floc particles into larger, more easily settleable particles through gentle stirring by hydraulic or mechanical means.

  • Transmission Injection Rights means Capacity Transmission Injection Rights and Energy Transmission Injection Rights.

  • Electrical Distance means, for a Generation Capacity Resource geographically located outside the metered boundaries of the PJM Region, the measure of distance, based on impedance and in accordance with the PJM Manuals, from the Generation Capacity Resource to the PJM Region.

  • Digital Signal Level 3 (DS-3 means the 44.736 Mbps third level signal in the time division multiplex hierarchy.