Produkt Kumlokk og Rammer, VOTEC Kabelkummer

Rev. 2, Juni 2023

Produkt Datablad

Produkt

Kumlokk og Xxxxxx, VOTEC Kabelkummer

Produktdetaljer
Produkt	Kumlokk og Ramme til Telekommunikasjon, iht. EN124-2, flytende
Anvendelse	Muliggjør adkomst til kommunikasjonskabler Produktene kan kun benyttes i VOTEC gategods, vil ikke passe inn i andre produsenters gategods. Produktene leveres komplett, kumlokk og kumramme, iht. krav i EN124-2.
Type	Firkant lokk og ramme, 1-, 2- eller 3 lokks, D400. Med dempepakninger for å unngå klapring, flytende ramme, lukkede spetthull og lås. Lokket vil låses i åpen posisjon for å unngå at lokket utilsiktet faller tilbake. Vær oppmerksom på at dimensjonene oppgitt i produkt teksten ikke gir max. / min. innvendige mål i tilhørende trekkekum, som kan variere noe mellom de forskjellige kum produsentene. Anbefalt max. / min. dimensjoner på innvendige mål av trekkekummene er oppgitt i PDB-UC-0003.
Komponenter	Lokk og Ramme av duktilt støpejern. Materialet på pakning påmontert lokket er poly uretan.
Produsent	RBA Ferro Industries Pvt. Ltd.
Henvisninger	Det henvises også til følgende nyttig informasjon: • Tilhørende FDV dokument, FDV-UC-0004 • Tilhørende Monteringsanvisning, MA-UC-0004 • VA Miljøblad nr. 2, Renovering av kum • VA Miljøblad nr. 31, Sikkerhet i kummer • VA Miljøblad nr. 32, Montering av kumramme og kumlokk

S. 1 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

Innholdsfortegnelse

Introduksjon 3

Produksjon og Miljø 3

Standarder, Godkjenninger og Sertifikater 7

S. 2 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

Introduksjon ‌

VOTEC Kumlokk og Rammer inngår i serien VOTEC, som er Brødrene Xxxx’x merkevare for produkter til bruk fortrinnsvis innen VMT segmentet.

Produktet er produsert av duktilt støpejern og samsvarer med EN124-2. Det er sertifisert av ICMQ (vil bli vedlagt på senere tidspunkt).

Produktet har lokk som låses i åpen tilstand, ca. 105 grader, for å hindre at lokket utilsiktet faller tilbake til lukket tilstand. Se mer informasjon om dette i tilhørende monteringsanvisning.

Produktene kan kun benyttes i VOTEC gategods, vil ikke passe inn i andre produsenters gategods. Produktene selges komplett, lokk og ramme, iht. krav i EN124-2.

Produksjon og Miljø ‌

Produktet produseres av RBA Ferro Industries Pvt. Ltd.

Produsenten innehar godkjente dokumenter for kvalitetssikring og produksjon, se vedlegg. Produsenten er kvalitetssikret og all produksjon for Xxxxxxxx Xxxx blir fulgt opp av egne inspektører hos produsenten.

Smelteovnene hos produsenten er elektriske. RBA har også installert solcellepaneler på taket for å utvinne elektrisitet og har stort fokus på miljøet og redusere CO2 avtrykket, se vedlegg 6.

Tekniske Data ‌
Last	D400, iht. EN124-2: 400kN, Gruppe 4
Materiale, hovedkomponenter	Duktilt Støpejern, ISO 1083, Grade 500-7 Max. Størrelse på kaviteter i støpejerns materialet: Ø5 mm. Slike kaviteter kan forekomme i materialet, også i overflaten på materialet.
Materiale, låser	Duktilt Støpejern, ISO 1083, Grade 500-7
Materiale, pakning	Poly Uretan
Overflate, Lokk	Anti-skli overflate med VOTEC design.
Sete, Lokk / Ramme	Pakningen som er montert på lokkene sikrer at de ligger stabilt og motvirker klapring / støy
Installasjon	Installeres i varm asfalt. Rammen må installeres slik at last ikke overføres til betongen. 4 stk. M16x100 skruebolter er montert i rammen for heving / senkning av lokk og ramme under installasjon. Se tilhørende Monteringsanvisning for mer informasjon.
Overflatebehandling	Ingen overflatebehandling, av miljøhensyn. Produktet vil da få noe overflate korrosjon (lys brun farge) ved lagring, men dette vil ikke ha noen negativ effekt på produktet.

S. 3 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

Mål / Dimensjoner ‌

3.1 1-Lokk ‌

Beskrivelse	NRF nr.	Lengde, utv. [mm]	Bredde, utv. [mm]	Høyde, utv. [mm]	Lengde, Skjørt [mm]	Bredde, Skjørt [mm]	Lengde, Lysåpning [mm]	Vekt per stk. [kg]
1-Lokk	3307009	912	900	205	710	687	637	144

Tabell 1

Anbefalte innvendige max. / min. mål på trekkekum:

Innvendige Mål, Kum, Lengde [mm]	Innvendige Mål, Kum, Bredde [mm]
720-750	700-730

Tabell 2

Seksjon A - A

S. 4 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

4.2 2-Lokk ‌

Beskrivelse

NRF nr.

Lengde, utv. [mm]

Bredde, utv. [mm]

Høyde, utv. [mm]

Lengde, Skjørt [mm]

Bredde, Skjørt [mm]

Lengde,

Lysåpning [mm]

Vekt per stk. [kg]

2-Lokk

3307011

1580

900

205

1394

687

1321

247

Tabell 3

Anbefalte innvendige max. / min. mål på trekkekum:

Innvendige Mål, Kum, Lengde [mm]	Innvendige Mål, Kum, Bredde [mm]
1405-1435	710-740

Tabell 4

Seksjon A - A

S. 5 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

4.3 3-Lokk ‌

Beskrivelse

NRF nr.

Lengde, utv. [mm]

Bredde, utv. [mm]

Høyde, utv. [mm]

Lengde, Skjørt [mm]

Bredde, Skjørt [mm]

Lengde,

Lysåpning [mm]

Vekt per stk. [kg]

3-Lokk

3307012

2294

900

205

2083

687

2010

354

Tabell 5

Anbefalte innvendige max. / min. mål på trekkekum:

Innvendige Mål, Kum, Lengde [mm]	Innvendige Mål, Kum, Bredde [mm]
2095-2125	710-740

Tabell 6

Seksjon A - A

S. 6 Produkt Datablad

PDB-UC-0004,

Rev. 2, Juni 2023

Produkt Datablad

Dempepakninger ‌

Dempepakning, inkl. festemateriell:

Beskrivelse

NRF nr.

For kum NRF Nr.

Dempepakning

2030041

3307009, 3307011 og 3307012. 1 pakke inneholder pakning og festemateriell til ett stk. lokk.

Standarder, Godkjenninger og Sertifikater ‌

Ledelse / Produksjon	ISO 9001	Vedlegg 1
	ISO 14001	Vedlegg 2
	OHSAS 18001	Vedlegg 3
	Material Sertifikat, Test Sample	Vedlegg 4
	RBA Kvalitets Plan	Vedlegg 5
	CO2 Reduksjoner, Juli 2019 - Juli 2020	Vedlegg 6
	EN124-1 og EN124-2, ICMQ	Vedlegg 7
	Test rapport, Maling, REACH	Vedlegg 8

Standarder	EN124-2	Sluktopper og kumtopper for kjøre- og fotgjengerområder - Del 2: Sluktopper og kumtopper laget av støpejern

S. 7 Produkt Datablad

Vedlegg 1 ‌

Vedlegg 2 ‌

Vedlegg 3 ‌

Vedlegg 4 ‌

Vedlegg 5 ‌

RBA FERRO INDUSTRIES PVT. LTD.

FOUNDRY DIVISION

QUALITY PLAN

Document No.:‐ RBA/Fdy/MG/D‐04 Effective Date:‐ 01‐01‐2011

Rev. Date:‐ 01.04.2018

Rev. No.:‐ 11

Page :‐ 1 of 18

SECTION : SAMPLING STAGE OF COMPONENT

AREA

Development

Pattern Shop

Development

PARAMETERS TO BE CHECKED

Receiving of Drawing

Feasibility Study

Pattern Inspection

Sampling Report (Casting Lay‐Out dimension)

Submission to customer

PPAP Submission (If Applicable)

INSPECTION PLAN

Every Enquiry

Pattern newly Received

New Produced Sample atleast ‐2 Nos

For Approval

SPECIFICATION & TOLERANCES

As per received drawing/Drawing Register

Newly prepared Pattern as per the drawing

As per received drawing

METHOD OF INSPECTION

Visual Study

As per the APQP Plan & Technical Feasibility Study

Manual By Inspector

As per the drawing & Customer Requirements (if

any)

Level 4 documentation requirement

INSTRUMENT TO BE USED

APQP Formats & Review Set‐up

Venier Caliper,Depth gauge,Steel Scale,Height Gauge

Visual

By Electronic means

RESPONSIBILITY

Development

Pattern Shop

Development

RECORDS

RBA/Fdy/PS/D‐02

RBA/Fdy/PS/R‐10

RBA/Fdy/PS/R‐02

RBA/Fdy/QA/R‐02

Via Mail

By Part Submission Warrant

REACTION PLAN

Feasible/Not Feasible/Notify to Marketing Head

Notify to Plant Head

Notify to Marketing Head

Pattern Shop

Releasing of Pattern for Production

After Approval from QA

As per Pattern realising

" certificate

‐‐‐‐‐‐‐‐

Pattern Shop

RBA/Fdy/PS/R‐06

Notify to Production

Prepared By Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
	FOUNDRY DIVISION					Page :‐ 2 of 18
QUALITY PLAN
SECTION : RAW MATERIAL TESTING
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
Lab	Radiation Test	One “composit” Sample/Batch	< 10 µR/H	By Instrument	NUCLEONIX	Lab	LAB/R‐08	Reject/Notify Plant Head
	(For PI & MS)
	For Steel scrap
	Carbon		0.65% max	Combustion	Strolein Apparatus
	Silicon		1.20% max	Ignition	lance,Measuring cylin
	Manganese		1.30% max	Titration	Balance,Measuring cylinder,Measuring burette
RAW MATERIAL	Sulphur		0.06% max	Titration
	Phosphorus		0.08% max	TItration

	Pig iron(DI)
	Carbon		3.20 ‐ 4.50%	Same as above	Same as above
	Silicon		0.6 ‐ 2.2%		‘’
	Manganese		0. 80% max		"
	Phosphorus		0.15% max		"
	Sulphur		0.06% max		"

	Pig iron(CI)
	Carbon		3.20 ‐ 4.50%		,,
	Silicon		0.8 ‐ 2.0%		"
	Manganese		0. 80% max		"
	Phosphorus		0.15% max		"
	Sulphur		0.06% max		"
	Fe‐Cr		Cr. : 60 ‐ 70%		,,

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 3 of 18
QUALITY PLAN
SECTION : RAW MATERIAL TESTING
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
Lab	For Shell Sand	Collect Material from 3 – 4 Different locations & mix to make a Sample			Sand sieve,Muffle furnace, Core gas determinator	Lab	RBA/Fdy/R‐08	Reject/Notify Plant Head
	AFS No		50 – 65%	Manual
	L.O.I		5.0 % Max
	Gas		25 cc/gm Max
	For Dextrine				Balance,Hot Plate Airoven,Muffle furnace Crucible, Cylinder
	Ash		1% Max	Ignition
	Insolubility		5 % Max	Titration
	For Fe‐Si Lumps	One Sample/Batch			Balance,Hot Plate Airoven,Muffle furnace Crucible, Balance,Hot Plate Airoven,Burette,Flask, Beaker
	Silicon		60 – 75%	Ignition
RAW MATERIAL Production Consumable	For Fe‐Mn
	Manganese		65 – 75%	Titration
	For Fe‐Cr
	Cr		60 – 70%	"
	For Fe‐Si‐Mg	As per Supplier T.C
	Magnesium		6 – 12%	Titration	Balance,Hot Plate Airoven,Muffle furnace,Burette, Flask,Beaker, Measuring, cylinder,Crucible, Decicator
	Fe‐Si		40 – 45%	Ignition
	For Pure Mg
	Magnesium		99%	"
	For Innoculine
	Silicon		60 – 75%	"
Note : 1) Reference standard IS: 1559 : Methods of chemical analysis of Ferro alloys & standard IS: 14529 : Chemical analysis of Ferro –Silicon Magnesium alloys

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 4 of 18
QUALITY PLAN
SECTION : RAW MATERIAL TESTING
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
Lab	For Graphite Powder(For Moulding)					Lab	RBA/Fdy/R‐08	Reject/Notify Plant Head
	Fixed Carbon	Collect Material from 3 – 4 Different locations & mix to make a Sample	75 % Min.	Weight Analysis	Airoven,Muffle furnace Crucible,Decicator
	Ash		2.0 % Max
	VM		5.0 % Max
	For Carburizer
	Fixed Carbon		95% Min.	"	"
	Ash		5% Max
	VM		1.5% Max
RAW MATERIAL Production Consumable	For Bentonite Powder
	Moisture	One Sample/Batch	5 – 14%	"	Air oven,pH Indicator Paper,Measuring Cylinder,M.B Clay tester,Measuring Cylinder
	PH Value		9 – 10.5
	Free Swelling		25 ml Min.
	M.B Value		80 ml /gm Min
	Gel formation Index		60 ml Min
	For Lustrius Carbon Additives
	Ash	"	2 – 6%	"	Airoven,Muffle furnace Crucible,Decicator
	VM		40 – 65%
	Fixed Carbon		30 – 55%
	For Silica Sand	"
	Moisture		1 % Max (Dry) 6% Max (Wet)	"	Airoven,Sand Washer, Beaker,Sieve Shaker
	Clay		2% Max
	AFS No.		45 – 70
	L.O.I		2% Max
	For Proprietary Items	Material Performance	Satisfactoty results	Line Performance		Lab/Production

Prepared By					Reviewed & Approved By :

RBA FERRO INDUSTRIES PVT. LTD.

FOUNDRY DIVISION

QUALITY PLAN

Document No.:‐ RBA/Fdy/MG/D‐04 Effective Date:‐ 01‐01‐2011

Rev. Date:‐ 01.04.2018

Rev. No.:‐ 11

Page :‐ 5 of 18

SECTION : UNIT SAND PREPRATION & SAND TESTING

AREA

PARAMETERS TO BE CHECKED

INSPECTION PLAN

SPECIFICATION & TOLERANCES

METHOD OF INSPECTION

INSTRUMENT TO BE USED

RESPONSIBILITY

RECORDS

REACTION PLAN

For Unit Sand Return Sand New Sand Bentonite

LCA

Moisture Compactibility

Each batch

90 – 98%

2.0 – 10 %

0.20% – 1.80%

0.10%. – 0.50%

3.0 – 5.0%

30–55%

Visual "

Visual

Sand multi controller

SS‐MLD

,, "

SS‐S.Plant

Auto save

MOULDING

L.O.I VM

Total clay Active clay

1/day 1/day 1/day 1/day

4.0 ‐ 9.0%

2.5 – 5.0%

11.0 ‐ 18.0%

7.0 ‐ 15.0%

Visual "

Muffle furnace

V.M Crucible

Sand Washer,Clay tester

M.B Clay tester

SS‐LAB

LAB/R‐03

Reject/Notify Plant Head

TC‐AC

1/day

2.0 ‐ 5.0

" Calculation .. ..

AFS No.

Compactibility GCS

GSS

Permeability Moisture

1/day 1/Hour 1/Hour 1/Hour 1/Hour 1/Hour

45 ‐ 70

30 ‐ 55%

1.10 – 1.80 Kg./cm2

0.30 – 0.70 Kg./cm2

130 ‐ 230

3.0 ‐ 5.0%

" Sandsiever, Sieve

" Compactibility meter

" Universal strenght M/c " ,,

" Permeability Tester

" Moisture Tester

SS‐S.Plant

LAB/R‐03

Prepared By Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
	FOUNDRY DIVISION					Page :‐ 6 of 18
QUALITY PLAN
SECTION : MOULD MAKING & CORE MAKING ( SHELL CORE )
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
MOULDING	MATCH 130
	Match plate Pattern	Each Pattern used	Pattern Dependent Parameter	Visual	‐‐‐‐‐‐	SS‐MLD	MLD/R‐09	Reset
			Pattern Independent Parameter	"		"	MLD/R‐09
	Mould Cake	Each Cake	No damaged Cake	"		"		Reject / Repair
	Squeez Pressure	Each Mould	1.2 – 10.0 Bar	"	VDU display	"		Adjust
	Mould Hardness	1/ Hour	H : 85 – 97	"	Mould HardnessTester	"	MLD/R‐12	Reject
	Changing of Heat No. on Pattern	After 1.0T metal pouring /As per cutomer requirement	As per the Heat No. of Melting	"	‐‐‐‐‐‐	"	MLD/R‐05	Reject
	First Mould Approval Report	Every day/Shift	As per the checking Parameters	"	Visual	"	MLD/R‐15	Reset

	ARPA
	Match plate Pattern	Each Pattern used	No undercut	Visual	‐‐‐‐‐‐	SS‐MLD	MLD/R‐03	Reject /dismount
	Match plate Pattern	Each Pattern used	No damaged bush pin	"	‐‐‐‐‐‐	"	,,	,,
	Mould Box	Each Box	No damaged box	"	‐‐‐‐‐‐	"	MLD/R‐04	Reject/Repair
	Mould Box	Each Box	No damaged bush pin	"	‐‐‐‐‐‐	"	,,
	Mould Hardness	4/ day	H= 85 – 95	"	Mould HardnessTester	"	MLD/R‐12	Reject
			V= 65 – 80	"	Mould HardnessTester	"	MLD/R‐12	,,
	Changing of Heat No. on Pattern	After 1.0T metal pouring /As per cutomer requirement	As per the Heat No. of Melting	"	‐‐‐‐‐‐	"	MLD/R‐05	Reject
	First Mould Approval Report	Every day/Shift	As per the checking Parameters	"	Visual	"	MLD/R‐15	Reset

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 7 of 18
QUALITY PLAN
SECTION: Core Sand making
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
CORE	SHELL CORE							Reject/ Readjust
	Temperature Setting	Each Batch	2000C – 3000C	Visual	Temperature indicator	Core shop Incharge	CORE/R‐09
	Investment time		20 – 90 Second		Timer		,,
	Core Scratch Hardness		60 – 90		Scratch hardness tester		CORE/R‐06
	Gas	1/Day	25cc / gm Max	Combustion	Core gas determinator		CORE/R‐07

	CO2 SAND
	Sodium silicate	Each Batch	6.5 – 9.5%	Visual	Weighing balance	Core shop Incharge	CORE/R‐05
	Ivacol Powder		1.0 – 2.5%
	Core Scratch Hardness		40 – 70		Scratch hardness tester		CORE/R‐06
	Gas	1/Day	25cc / gm Max	Combustion	Core gas determinator		CORE/R‐07

	OIL CORE SAND
	Dextrin	Each Batch	2.0 – 4.0 %	Visual	Measuring Can	Core shop Incharge	CORE/R‐05
	Bentonite		1.0 – 2.5 %		,,
	Oil		2.0 – 3.5 %		,,
	Water		3.5 – 4.5 %		,,
	Baking Temperature		160 0 C – 250 0 C		Temperature Indicator
	Baking Time		2.0 – 3.0 hrs		Timer
	Core Scratch Hardness		40 – 70		Scratch hardness tester		CORE/R‐06
	Gas	1/Day	40cc / gm Max	Combustion	Core gas determinator		CORE/R‐07

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 8 of 18
QUALITY PLAN
SECTION: Core Sand making
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
CORE	NO BAKE CORE
	Resin Part – A	Each Batch	2.00 – 2.50 %	Visual	Measuring Can	Core shop Incharge	CORE/R‐05	Reject/Re‐adjust
	Resin Part – B		5 – 10 % of Part–A		,,
	Resin Part – C		18 – 22 % of Part – A		,,
	Core Scratch Hardness		60 – 90		Scratch hardness tester		CORE/R‐06
	Gas	1/Day	20cc / gm Max	Combustion	Core gas determinator		CORE/R‐07

	CORE SET
	Dextrin	Each Batch	2.0 – 3.5 %	Visual	Measuring Can	Core shop Incharge	CORE/R‐05	Reject/Re‐adjust
	Bentonite		1.5 – 2.5 %		,,
	Core Set		2.30 – 3.50 %		,,
	Core Scratch Hardness		50 –70		Scratch hardness tester		CORE/R‐06
	Gas	1/Day	20cc / gm Max	Combustion	Core gas determinator		CORE/R‐07
	Viscosity of Core Paint	As per requirement	12 – 16 seconds	Visual	B4 Cup		CORE/R‐04

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 9 of 18
QUALITY PLAN
SECTION: Core Sand making for COLD BOX CORE SHOOTER MACHINE
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
CORE	SAND
	AFS No	Each Batch	50 ‐ 65	Weight analysis	Air Oven ,Sand washer, Beaker ,Sieve	Lab	RBA/Fdy/R‐08	Reject/Notify Plant Head
	Moisture		6 % Max
	Clay		2 % Max

	RESIN & HARDNER ADDITION LEVEL
	Resin	1/Day	1.0 ‐1.5 % wt of sand	Visual	Measuring Can	Core shop Incharge	CORE/R‐11	Reject
	Hardener	"	1.0 ‐1.5 % wt of sand	,,	,,		,,

	SAND MAKING CYCLE TIME
	Sand + Resin	1/Day	2 Minutes mixing	Visual	watch	Core shop Incharge	CORE/R‐11	Reject
	(Sand + Resin) + Hardener	"	1 Minute mixing	,,			,,

	CORE GAS	1/Day	20 cc /gm Max	Combustion	Core gas determinator	Core shop Incharge	CORE/R‐06 /R07	Reject
	SCRATCH HARDNESS	3/Day	60 ‐ 90	Visual	Scratch hardness tester
	Bench life of Mixing Sand	Each Batch	45 minutes max	"	watch

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 10 of 18
QUALITY PLAN
SECTION : METAL CHARGE PREPARATION
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
MELTING	DI Metal (Normal heat)			Visual	Weighing Scale	SS‐MLT	RBA/Fdy/MLT/R‐02	Readjust
	Pig iron	Each Heat	00 % –– 50%
	MS Scrap		20 % –– 80 %
	DI Foundry return		80 % –– 20 %
	Carburizer		0.3 % –– 2.0 %
	Fe‐Si		0.0 % –– 2.5 %
	Fe ‐ Mn		0.0 % –– 1.0 %

	DI Metal (Sintering heat)
	Pig iron	Each Heat	30 % –– 50 %
	MS Scrap		20 % –– 30 %
	DI Foundry return		50 % –– 20 %
	Carburizer		1.0 % Max
	Fe‐Si		0.5 % Max
	Fe‐Mn		0.8 % Max
	Copper		0.5 % Max (Optional)

	CI Metal
	Pig iron	Each Heat	00 % –– 60 %
	MS Scrap		15 % –– 40 %
	CI Foundry return		85 % –– 00 %
	Carburizer		0.3 % –– 1.0 %
	Fe‐Si		0.4 % –– 1.5 %
	Fe‐Mn		0.2 % –– 1.5 %
	Fe‐Cr		0.4 % Max (optional)
	Cu		0.6 % Max (optional)
	Sn		0.08 % Max (optional)

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
	FOUNDRY DIVISION					Page :‐ 11 of 18
QUALITY PLAN
SECTION : METAL PREPARATION, TAPPING & POURING
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
MELTING (DI)	C.E.	Each Heat (Base Metal)	4.00 – 4.70 %	Visual	CE Analyser	SS‐MLT	RBA/Fdy/MLT/R‐02	Readjust
	Carbon	,,	3.60 – 4.00 %
	Silicon	,,	1.30 – 2.00 %
	Tapping Temperature	,,	1590 – 1490 0C		Immersion Pyrometer
	Fe‐Si‐Mg	Each Treatment ladle	1.0–1.8% / liquid metal		Weighing Scale		MLT/R‐03	Readjust
	DI scrap / Boring	,,	0.5–1.5% / liquid metal		,,		"	Readjust/Return to F/c
	Treatment time	,,	40 second Min		Watch		"	Return to F/c
	During direct pouring						,,
	Innoculation	Each pouring ladle	0.4–0.6% of liquid metal	Visual	Measured Spoon		MLT/R‐03	Readjust
	Pouring Temperature	3/heat	1460 – 1340 0C		Immersion Pyrometer		"
	Pouring Time	Each treatment	8 minutes max after treatment		Hooter/Watch		MLT/R‐07
	Before transfering Mg treated metal to Press pour machine	Each Treatment ladle
	Innoculation	Each mold	0.4–0.6% of liquid metal	Visual	Measured Spoon
	Receiving Temperature (In treatment ladle to Press pour m/c)	Each Treatment ladle	1420 ‐ 1470 0C		Immersion Pyrometer		MLT/R‐07	Return to F/c
	Transfer time	Each Treatment ladle	8 minutes max after treatment		Hooter/Watch		MLT/R‐03
	During pouring from Press pour m/c
	Innoculation	Each mold	0.1 – 0.4% of liquid metal	As per flow gauge setting	MSI machine		MLT/R‐08	Resaet
	Pouring Temperature	Each mould	1460 – 1340 0C	Visual	Immersion Pyrometer		MLT/R‐07	Stop pouring/readjust temperature, Relook pattern methoding
	Pouring Time	1 / Each part	As per data bank	Visual	MSI machine		MLT/R‐07	Stop pouring/readjust temperature, Relook pattern methoding
	Sn, Cu (optional)	Each Heat	Sn : 0.01 – 0.07%	Visual and Chemical Analysis	Spectro/Chemical Testing Instruments	SS‐LAB	LAB/R‐05B	Readjust
	Sn, Cu (optional)	Each Heat	Cu : 0.10 – 0.50%	Visual and Chemical Analysis	Spectro/Chemical Testing Instruments	SS‐LAB	LAB/R‐05B	Readjust

Prepared By					Reviewed & Approved By :

SECTION : METAL PREPARATION, TAPPING & POURING

RBA FERRO INDUSTRIES PVT. LTD.

FOUNDRY DIVISION

QUALITY PLAN

Document No.:‐ RBA/Fdy/MG/D‐04 Effective Date:‐ 01‐01‐2011

Rev. Date:‐ 01.04.2018

Rev. No.:‐ 11

Page :‐ 12 of 18

AREA

C.E.

PARAMETERS TO BE CHECKED

INSPECTION PLAN

Each Heat (Base Metal)

SPECIFICATION & TOLERANCES

3.50 – 4.10 %

METHOD OF INSPECTION

INSTRUMENT TO BE USED

RESPONSIBILITY

RECORDS

REACTION PLAN

Carbon	,,	3.10 – 3.40 %	Visual	CE Analyser	MLT/R‐02	Readjust
Silicon	,,	1.30 – 1.80 %
Tapping Temperature	,,	1500 – 1440 0C		Immersion Pyrometer	MLT/R‐03
During direct pouring
Innoculation	Each pouring ladle	0.15–0.3% of liquid metal		Measured Spoon	MLT/R‐03
Pouring Temperature	3/heat	1440 – 1330 0C	Visual	Immersion Pyrometer	"	Readjust
Pouring Time	Each pouring ladle	9 minutes max after inoculation		Watch	"

MELTING (CI)

Before transfering metal to Press pour machine

Innoculation Each bull ladle 0.15–0.3% of liquid metal Measured Spoon

SS‐MLT

MLT/R‐03

Receiving Temperature (In bull ladle to Press pour m/c)

Each bull ladle

1400 ‐ 1470 0C

Visual

Immersion Pyrometer

MLT/R‐07

Readjust/Return to F/c

Transfer time

Each bull ladle

9 minutes max after inoculation

Watch

MLT/R‐03

During pouring from Press pour m/c

Innoculation Each mold 0.1 – 0.4% of liquid metal As per flow gauge setting MSI machine

MLT/R‐08 Resaet

Pouring Temperature Pouring Time

Sn, Cu (optional

Each mold 1 / Each part

Each Heat

1440 – 1330 0C

As per data bank Sn : 0.01 – 0.07%

Cu : 0.10 – 0.50%

Visual

Visual and Chemical Analysis

Immersion Pyrometer

MSI machine

Spectro/Chemical Testing Instruments

SS‐LAB

MLT/R‐07 "

LAB/R‐05

Stop pouring/readjust Relook pattern methoding

Readjust

Prepared By Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 13 of 18
QUALITY PLAN
SECTION : FINAL METAL COMPOSITION / MATRIX
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
LAB	FOR ( DI ) METAL	Each Treatment			Spectro/Chemical Testing Instruments	Lab	LAB / R – 05B	Notify Melting/ Plant Head
	C.E.		4.20 – 4.70%	Calculation
	Carbon		3.40 – 3.80%
	Silicon		2.20 – 2.80%
	Manganese		0.15 – 1.00%	Visual and Chemical Analysis
	Sulphur		0.02 % max
	Phosphorus		0.08 % max
	Magnesium		0.03‐0.06 %
	Alloys (optional)		As per Requirement
	FOR MATRIX
	Nodularity		80% min	Visual	Microscope
FINAL METAL	Ferrite		As per Requirement		,,
	Pearlite		As per Requierment		,,
	FOR ( CI ) METAL	Each Ladle
	C.E.		3.50 – 4.10%	Calculation Visual and Chemical Analysis	Spectro/Chemical Testing Instruments
	Carbon		2.90 – 3.40%
	Silicon		1.50 – 2.30%
	Manganese		0.40 – 1.00%
	Sulphur		0.10% max
	Phosphorus		0.12% max
	Cromium		0.25% max
	Copper		0.40% max
	Tin		0.07% max
	FOR MATRIX
	Graphite Flakes(Type)		ASTM ‘A’Type	Visual	Microscope
	Pearlite		As per Requirement		,,
	Ferrite		,,		,,

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
						Page :‐ 14 of 18
QUALITY PLAN
SECTION : PHYSICAL PROPERTIES
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
LAB	DI	Each Heat	190 – 270 for – IS 1865 ( SG‐600/3 )	Visual	Brinnel Hardness Tester	Lab	LAB/R‐05(B)	Notify Melting/ Plant Head
	Casting Hardness		160 – 240 for – IS 1865 ( SG‐500/7 )
	(BHN)		170 – 230 as per BS EN 124 or ISO 1083 ( 500/7 )
			160 – 210 for – IS 1865 ( SG 450/10 )
			201 Max for– IS 1865 ( SG‐400/12 )
			187 – 255 for – ASTM A 536 (Gr –80–55–06)
			156 – 217 for – ASTM A 536 (Gr –65–45–12)
	Tensile Strength		600 Mpa Min for – IS 1865 ( SG‐600/3 )		UTS M/C
			500 Mpa Min for – IS 1865 ( SG‐500/7 )
			450 Mpa Min for – IS 1865 ( SG 450/10 )
			400 Mpa Min for– IS 1865 ( SG‐400/12 )
PHYSICAL			552 Mpa Min for – ASTM A 536 (Gr –80–55–06)
PROPERTIES			448 Mpa Min for – ASTM A 536 (Gr –65–45–12)
	Elongation		3 % Min for – IS 1865 ( SG‐600/3 )
			7 % Min.for – IS 1865 ( SG‐500/7 )
			10 % Min for – IS 1865 ( SG 450/10 )
			12 % Min. for– IS 1865 ( SG‐400/12 )
			6 % Min for – ASTM A 536 (Gr –80–55–06)
			12 % Min for – ASTM A 536 (Gr –65–45–12)
	Yield Strength		370 Mpa Min for – IS 1865 ( SG‐600/3 )
			320 Mpa Min for– IS 1865 ( SG‐500/7 )
			310 Mpa Min for – IS 1865 ( SG 450/10 )
			250 Mpa Min for – IS 1865 ( SG‐400/12 )
			379 Mpa Min for – ASTM A 536 (Gr –80–55–06)
			310 Mpa Min for – ASTM A 536 (Gr –65–45–12)
	CI		160 – 220 for – IS 210 ( FG‐200 )		Brinnel Hardness Tester
	Casting Hardness (BHN)		180 – 220 for – IS 210 ( FG‐220 )
			180 – 230 for – IS 210 ( FG‐260 )
			180 – 230 for – IS 210 ( FG‐300 )
	Tensile Strength		200 Mpa Min for – IS 210 ( FG‐200 )		UTS M/C
			200 Mpa Min as per BS EN 124 or ISO 185 ( Gr.20)
			220 Mpa Min for – IS 210 ( FG‐220 )
			260 Mpa Min for – IS 210 ( FG‐260 )
			300 Mpa Min for – IS 210 ( FG‐300 )

Prepared By					Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.					Document No.:‐ RBA/Fdy/MG/D‐04
						Effective Date:‐ 01‐01‐2011
						Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION					Rev. No.:‐ 11
	FOUNDRY DIVISION					Page :‐ 15 of 18
QUALITY PLAN
SECTION : SHOT BLASTING & FETTLING
AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN	SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
SHOT BLASTING & FETLING	Shot Size	Each batch	0.7 ‐ 1.2 mm	Measuring	Vernier Caliper	SS FTL	……	Reject/

	Surface Finish	Each Casting	Sand free casting	Visual	Visual	"

	Duration of blasting(Hanger type blasting machine)	Each batch	5 – 12 minutes	Visual	Timer	,,	FLT/R‐02B	Notify Plant Head /Rectify

	Duration of blasting Peen blasting machine	Each batch	5 – 20 mnutes	Visual	Timer	“	FLT/R‐02B	,,

Prepared By					Reviewed & Approved By :

SECTION : FINAL INSPECTION

RBA FERRO INDUSTRIES PVT. LTD.

FOUNDRY DIVISION

QUALITY PLAN

Document No.:‐ RBA/Fdy/MG/D‐04 Effective Date:‐ 01‐01‐2011

Rev. Date:‐ 01.04.2018

Rev. No.:‐ 11

Page :‐ 16 of 18

AREA

PARAMETERS TO BE CHECKED

INSPECTION PLAN

SPECIFICATION & TOLERANCES

METHOD OF INSPECTION

INSTRUMENT TO BE USED

RESPONSIBILITY

RECORDS

REACTION PLAN

QUALITY

For RAW CASTING

Visual Defects Blow hole Shrinkage Cold shut

100% No visual defects Visual ‐‐‐‐‐‐‐ QA ‐‐‐‐ Reject/Rework 100% No Blow hole Visual ‐‐‐‐‐‐‐ " ‐‐‐‐ "

100% No Shrinkage Visual ‐‐‐‐‐‐‐ ,, ‐‐‐‐ ,, 100% No Cold shut Visual ‐‐‐‐‐‐‐ ,, ‐‐‐‐ ,,

ASSURANCE

(For Normal castings)

Specified Dimensions of each

item.

Casting weight

One / lot of Production

batch

One / lot of Production batch

As per Drawing

dimension

As per p.o.weight

Visual Weighing

Different Measuring

Instruments QA

Weighing Scale ,,

QA/R‐02 QA/R‐07

Reject/Rework

Notify Plant Head/Rectify

Gauge Checking

As Required

As per gauge dimension

Visual

Gauge

,, ‐‐‐‐

Reject/Rework

For MACHINED CASTING

Dimensions

As Per CP As per Drawing dimention

Visual Gauge / Fixture / Measuring Instrument

QA QA/R‐03 Reject/Rework

Prepared By Reviewed & Approved By :

	RBA FERRO INDUSTRIES PVT. LTD.						Document No.:‐ RBA/Fdy/MG/D‐04
							Effective Date:‐ 01‐01‐2011
							Rev. Date:‐ 01.04.2018
	FOUNDRY DIVISION						Rev. No.:‐ 11
							Page :‐ 17 of 18
QUALITY PLAN

AREA	PARAMETERS TO BE CHECKED	INSPECTION PLAN		SPECIFICATION & TOLERANCES	METHOD OF INSPECTION	INSTRUMENT TO BE USED	RESPONSIBILITY	RECORDS	REACTION PLAN
Quality Assurance (Foundry)	For Manhole cover	Sample		As per Specification of EN 124‐2:2015	Visual	Filler gauge,Venier Caliper,Depth gauge,Steel tape,Steel Scale	Inspection Foundry & Ware house	RBA/Fdy‐1/QA/R‐02‐2	Check 3 random samples out of the lot, If found o.k., accept the whole lot If any one sample fails. Check 5 new random samples , If all the 5 samples are o.k. accept the whole lot. If any one of the 5 random samples found defective , reject the whole lot.
	Aspects of Inspection	Size	Frequency
	Clear opening	3	Supply / Receive Lot
	Over base
	Depth
	Dimentions
	Frame bearing area
	Load bearing capacity
	Permanent set
	Securing of the cover / grating within the frame
	Skid resistence
	Child safety
	Tilt test					Venier Caliper,Steel Scale,Load test machine,Test block 75 mm dia		RBA/Fdy‐1/QA/R‐25
	Weight			As per P.O. Weight	Weighing	Weighing scale		RBA/Fdy‐1/QA/R‐02‐2
	Pull test	3	When developed	As per the Customer Specification / Standard	Visual	Pull test machine,Vernier Caliper		RBA/Fdy‐1/QA/R‐26
	Load	3 / Lot dispatched it will be repeated once in at least every six month or 1: 5000			By Application of Load	Load test m/c		Record No. of Customer Specific Requirement Matrix
	Painting (Epoxy ,CED,Powder coating,Phosphating)	One / Lot		As per customer requirement	Measurement	Viscosity, Coating thickness measuring instrument	Inspection ware house	RBA/Fdy/PHT/R‐ 03 and RBA/Fdy/CED/R‐ 03 & 04 & RBA/Fdy/PCT /R‐01	Re‐paint/ Re‐coating/ Re‐Phosphating

Prepared By (QC Manager)						Reviewed & Approved By :

RBA FERRO INDUSTRIES PVT. LTD.

FOUNDRY DIVISION

QUALITY PLAN

Document No.:‐ RBA/Fdy/MG/D‐04 Effective Date:‐ 01‐01‐2011

Rev. Date:‐ 01.04.2018

Rev. No.:‐ 11

Page :‐ 18 of 18

AREA

PARAMETERS TO BE CHECKED

For Engg. Component

Visual Inspection of Castings

Machining of Castings

Dimensional Inspection

INSPECTION PLAN

Size 100%

Every Lot

SPECIFICATION & TOLERANCES

As Per Drawing As per Machining

Process check Sheet of every operation/Periodical Inspection Record

As Per Drawing

METHOD OF INSPECTION

As per the visual standard/Display

As per the list of Measuring Instruments

INSTRUMENT TO BE USED

Standard

Vernier calliper, Height Gauge,Depth Gauge,Dial Gauge etc.

‐‐do‐‐

RESPONSIBILITY

CNC Receiving Inspector

CNC Shop Incharge

RECORDS

RBA/Fdy/CNC‐QC/D‐ 01

RBA/Fdy/MC/D‐ 06

RBA/Fdy/MC/R‐ 08

RBA/Fdy/CNC‐QC/R‐ 02

REACTION PLAN

Reject/Notify to QC Manager

‐‐do‐‐

CNC Shop/ Induction Hardening

Induction Hardening

Tempering

MPI Testing

DP Testing HRC Hardness

Once per day

100 % of total Lot

100 % of total Lot of Induction Hardening

/ As per customer Specific requirement

Suspected Material of the lot MPI done

Every after 2 Hours of production run

As per the setting parameters

165ᵒC

As per the setting parameters

Visually 53 Min.

As per the Check Points & WI

Visual Display

As per the check Points Sheet & WI

As per the Work Instruction

WI for HRC Hardness testing

Pressure Gauge,Vernier,Pyromete r, filler Gauge, Refractrometer, Polymer etc.

Visual Temp. Indicator

MPI Machine

Chemical & Visual

HRC Hardness testing Machine

Incharge Heat treatment

RBA/Fdy/HT/R‐ 02 & R‐07

‐‐‐‐‐‐

RBA/Fdy/HT/R‐ 04 &

RBA/Fdy/LAB/R‐ 15

‐‐‐‐‐

RBA/Fdy/WIO/LAB/D‐25

Reject/Notify to QC Manager

‐‐‐‐‐

Reject/Notify to QC Manager

Micro Hardness

Every after 4 Hours of production run

Case depth‐0.51 min

First piece approval Report Check Points in approval "

report

RBA/Fdy/HT /R‐09

Reject/Notify to QC Manager

Painting (Epoxy ,CED,Powder coating,Phosphating)

One / Lot

As per customer requirement

Measurement/As per the check Point

Viscosity, Coating thickness measuring instrument

Inspection ware house/ LAB

RBA/Fdy/PHT/R‐ 03 and

RBA/Fdy/CED/R‐ 03 & 04 & RBA/Fdy/PCT /R‐01

Re‐paint/ Re‐coating/ Re‐Phosphating

Prepared By Reviewed & Approved By :

Vedlegg 6 ‌

Vedlegg 7 ‌

CERTIFICATE N°	CERTIFICATO N°
P534
COMPANY	AZIENDA
RBAFerro Industries Private Limited 0/0 Xxxxx Xxxx Xxxx, Xxxxxxx Xxxxx, Xxxxx 000, Xxxxxxx 000000 - Xxxx Xxxxxx, Xxxxx
PRODUCTION UNIT	UNITA’ PRODUTTIVA
NH6, Village and Post Office: Prasastha, Xxxxxx Xx - 000000 Xxxx Xxxxxx Xxxxx
SCOPE OF THE CERTIFICATE	OGGETTO DEL CERTIFICATO
GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS Dispositivi di coronamento e chiusura per zone di circolazione utilizzate da pedoni e da veicoli
REFERENCE STANDARDS	NORME DI RIFERIMENTO
EN 124-1:2015, EN 124-2:2015
CERTIFICATION SYSTEM	SISTEMA DI CERTIFICAZIONE
General Agreement Conditions for the product certification – CP DOC 229 Condizioni Generali di Contratto per la Certificazione di prodotto - CP DOC 229 Particular rules for gully tops and manhole tops - CP DOC 243 Regolamento particolare per dispositive di coronamento e chiusura – CP DOC 243 Instructions for the application of the EN 124:2015 - UNI/TR 11671:2017 Indicazioni per l’applicazione della serie EN 124:2015 – UNI/TR 11671:2017
PRODUCTS	PRODOTTI
3307011 RBAD-1441 Manhole Top EN 124-2 – D400 – 2/2 – 614 – F – RP

First Issue

Prima Emissione

Current Issue

Emissione Corrente

Expiry Date

Scadenza

11/05/2022 11/05/2022 31/12/2022

THE PRESIDENT AND GENERAL MANAGER ING. XXXXXXX XXXXXXXX

1 of 1

Vedlegg 8 ‌

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

RBA FERRO INDUSTRIES PVT LTD.

498-50. NH6, PRASASTHA, KOLKATA, WEST BENGAL,-711302

INDIA

CONTACT PERSON: XXXXXXXXXXXX XXXXXXX

THE FOLLOWING SAMPLE(S) WAS/WERE SUBMITTED AND IDENTIFIED BY/ON BEHALF OF THE CUSTOMER AS : SAMPLE DESCRIPTION SYN. ENA. XXXX XXXXXX XXXXX PAINT

COLOUR BROWN

ORDER NO. 50116915

END USE TO COAT MANHOLE COVER

XXXXX XXXXXXX XXXX

BUYING HOUSE SAINT GOBAIN

COUNTRY OF ORIGIN INDIA

COUNTRY OF DESTINATION NORWAY

CONDITION OF SAMPLE COMPLETE AND OK

THE LOCATION OF PERFORMANCE OF THE LABORATORY ACTIVITIES: SGS CHENNAI LABORATORY

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

LAB PROVIDED DETAILS:

SAMPLE RECD ON 22/02/2023

TEST PERFORMING DATE 22/02/2023 TO 13/03/2023

SUMMARY OF TEST RESULT:

TEST REQUESTED	CONCLUSION
1. ORGANO TIN COMPOUNDS (OTC)	SEE RESULT
2. TOTAL LEAD CONTENT	SEE RESULT
3. TOTAL CADMIUM CONTENT	SEE RESULT
4. PHTHALATE CONTENT TEST	SEE RESULT
5. POLYCYCLIC AROMATIC HYDROCARBONS (PAHS) CONTENT	SEE RESULT
6. Two hundred and thirty-three (233) substances in the Candidate List of Substances of Very High Concern (SVHC) for authorization published by European Chemicals Agency (ECHA) on and before Jan 17, 2023 regarding Regulation (EC) No 1907/2006 concerning the REACH.	--
According to the specified scope and analytical techniques, concentrations of tested SVHC are < 0.1% (w/w) in the submitted sample. Concentrations of tested SVHC with specific concentration limit (SCL) # < 0.1% (w/w) set in Regulation (EC) No. 1272/2008 and its amendments are < reporting limit. # Please refer to Note 2 on the following page	PASS

TEST(S) RESULT & METHOD: PLEASE REFER TO NEXT PAGE(S). RESULTS APPLY TO THE SAMPLE AS RECEIVED

_ Per Pro SGS India Pvt. Ltd.

XXXXXX XXXXXXX (Technical Manager) Authorized Signatory

Email your Test Report Related Enquiries at Xxxxxxxx.XXX@xxx.xxx

XXX Xx. : 2348800601 40049443 Page 1 of 16 Control No.:1448501644

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at xxxx://xxx.xxx.xxx/xxxxx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at xxx.xxx.xxx/xxxxx_x-xxxxxxxx.xxx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.” Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

TEST RESULT :

1. ORGANO TIN COMPOUNDS (OTC):-

METHOD: With reference to ISO/TS 16179: 2012. Analysis was conducted by GC-MS.

Organotin	TEST RESULT (% by weight of tin)	Recommended Max. Limit (%)
Tributyltin (TBT) Calculated as tin	Not Detected	--
Triphenyltin (TPhT) Calculated as tin	Not Detected	--
Tricyclohexyltin (TCyT) Calculated as tin	Not Detected	--
Trioctyltin (TOT) Calculated as tin	Not Detected	--
Tripropyltin (TPT) Calculated as tin	Not Detected	--
Trimethyltin (TMT) Calculated as tin	Not Detected	--
Dibutyltin (DBT) Calculated as tin	Not Detected	--
Dioctyltin (DOT) Calculated as tin	Not Detected	--

Detection Limit: 0.01 %

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

Note:

- Testing has been subcontracted to SGS Chennai lab.

XXX No. : 2348800601 40049443 Page 2 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

2. TOTAL LEAD CONTENT:

Method: With reference to EN 16711-1: 2015. Analysis was conducted by ICP-MS.

Test Name	CAS-No.	Test Result (mg/kg)	Requirement (mg/kg)
Total Lead Content	7439-92-1	Not Detected	/

Detection Limit: 20 mg/kg

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

Note:

- mg/kg = milligram per kilogram

- Testing has been subcontracted to SGS Chennai lab.

3. TOTAL CADMIUM CONTENT:

Method: With reference to EN 16711-1: 2015. Analysis was conducted by ICP-MS.

TEST NAME	CAS-No.	TEST RESULT (mg/kg)	REQUIREMENT (mg/kg)
Total Cadmium Content	7440-43-9	Not Detected	/

Detection Limit: 20 mg/kg

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

Note:

- mg/kg = milligram per kilogram

- Testing has been subcontracted to SGS Chennai lab.

XXX Xx. : 2348800601 40049443 Page 3 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

4. PHTHALATE CONTENT TEST:

Method : With reference to ISO 14389:2014. Analysis was conducted by GC-MS.

Test Name	CAS NO.	Test Result (mg/kg)	Requirement (%)
Dibutyl Phthalate (DBP)	84-74-2	Not Detected	/
Benzylbutyl Phthalate (BBP)	85-68-7	Not Detected
Bis-(2-ethylhexyl) Phthalate (DEHP)	117-81-7	Not Detected
Diisoheptyl phthalate (DIHP)	00000-00-0	Not Detected
Bis (2-methoxyethyl) phthalate (DMEP)	117-82-8	Not Detected
Bis-isopentyl phthalate (DiPP)	605-50-5	Not Detected
Di-n-pentylphthalate (DnPP)	84-66-2	Not Detected
Di-n-Hexylphthalate (DnHP)	84-75-3	Not Detected
Diisobutyl phthalate (DIBP)	84-69-5	Not Detected
Diisononyl Phthalate (DINP)	00000-00-0	Not Detected
Di-n-octyl Phthalate (DNOP)	117-84-0	Not Detected
Diisodecyl Phthalate (DIDP)	00000-00-0	Not Detected

Detection Limit: 0.01 mg/kg

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

Note:

- Testing has been subcontracted to SGS Chennai lab.

JOE No. : 2348800601 40049443 Page 4 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

5. POLYCYCLIC AROMATIC HYDROCARBONS (PAHS) CONTENT (REACH) ANNEX XVII ENTRY 50 PARAGRAPH 5 TO 8):

Method : With reference to AfPS GS 2019:01 PAK ..Analysis was conducted by Gas Chromatography-Mass Spectrometry.

Test Item	CAS Number	Result (mg/kg)	Permissible Limit (mg/kg)
Benz [a] anthracene	56-55-3	Not Detected	--
Chrysene	218-01-9	Not Detected	--
Benz [e] acephenanthrylene	205-99-2	Not Detected	--
Benzo [k] fluoranthene	207-08-9	Not Detected	--
Benzo [j] fluoranthene	205-82-3	Not Detected	--
Benzo [a] pyrene	50-32-8	Not Detected	--
Benzo [e] pyrene	192-97-2	Not Detected	--
Dibenz[a,h] anthracene	53-70-3	Not Detected	--
Sum of 8 PAH	--	Not Detected	--

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

Detection Limit: 1 mg/kg

Note:

- mg/kg = milligram per kilogram

- Testing has been subcontracted to SGS Chennai lab.

XXX No. : 2348800601 40049443 Page 5 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

6. Two hundred and thirty-three (233) substances in the Candidate List of Substances of Very High Concern (SVHC) for authorization published by European Chemicals Agency (ECHA) on and before Jan 17, 2023 regarding Regulation (EC) No 1907/2006 concerning the REACH.

Remark :

1. The chemical analysis of specified SVHC is performed by means of currently available analytical techniques against the following SVHC related documents published by ECHA:

- xxxxx://xxxx.xxxxxx.xx/xxxxxxxxx-xxxx-xxxxx(Xxxxxxxxx list)

These lists are under evaluation by ECHA and may subject to change in the future.

2. If a SVHC is found greater than or equal to 0.1% (w/w) and/or the specific concentration limit which is set in Regulation (EC) No 1272/2008 and its amendments, client is suggested to prepare a Safety Data Sheet (SDS) against the SVHC to comply with the supply chain communication obligation under Regulation (EC) No 1907/2006, in which:

- a substance that is classified as hazardous under the CLP Regulation (EC) No 1272/2008.

- a mixture that is classified as hazardous under the CLP Regulation (EC) No 1272/2008, when it contains a substance with concentration equal to, or greater than the classification limit as set in Regulation (EC) No. 1272/2008; or

- a mixture is not classified as hazardous under the CLP Regulation (EC) No 1272/2008, but contains either:

(a) a substance posing human health or environmental hazards in an individual concentration of ≥ 1 % by weight for mixtures that are solid or liquids (i.e., non-gaseous mixtures) or ≥ 0.2 % by volume for gaseous mixtures; or

(b) a substance that is PBT or vPvB in an individual concentration of ≥ 0.1 % by weight for mixtures that are solid or liquids (i.e., non- gaseous mixtures); or

(c) a substance on the SVHC candidate list (for reasons other than those listed above), in an individual concentration of ≥ 0.1 % by weight for non-gaseous mixtures; or

(d) a substance for which there are Europe-wide workplace exposure limits

Test Sample:

Sample description: Liquid chemical (Black)

Tested Item: SYN. ENA. XXXX XXXXXX XXXXX PAINT

XXX Xx. : 2348800601 40049443 Page 6 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

Test Method :

SGS In-House method - Analyzed by ICP-OES, GC-MS, UV-VIS, HPLC-DAD, HPLC-MS and colorimetric method.

Test Result :

No.	Substance Name	CAS No./ EC No.	RL (%) / SCL (%)#	Concentration (%)
-	All tested SVHC	-	-	ND

Notes :

1. RL = Reporting Limit. All RL are based on homogenous material. ND = Not detected (lower than RL)

2. # SCL = Specific Concentration Limit. All SCL are set out in Regulation (EC) No 1272/2008 and its amendments. Specific concentration limits and generic concentration limits are limits assigned to a substance indicating a threshold at or above which the presence of that substance in another substance or in a mixture as an identified impurity, additive or individual constituent leads to the classification of the substance or mixture as hazardous. The SVHCs with SCL values <0.1% are specified in the test result tables.

* The test result is based on the calculation of selected element(s) / marker(s) and to the worst-case scenario.

The client is advised to review the chemical formulation to ascertain above metal substances present in the article.

RL = 0.001% is evaluated for element (i.e. cobalt, arsenic, lead, chromium (VI), aluminum, zirconium, boron, strontium, zinc, antimony, titanium, barium and cadmium respectively), except molybdenum RL= 0.0005%.

▼ Regulation (EC) No 1272/2008 Classification, Labelling and Packaging of Substances and Mixtures, and its amendments.

ª Client has the obligation to comply with the conditions of Authorization of substance of very high concern included in the Annex XIV of the Regulation (EC) No. 1907/2006, unless the use has been exempted from Authorization. Article 56(6) of Regulation (EC) No. 1907/2006 specified the concentration limit requirement of Authorization of SVHC in mixture.

The ECHA SVHC authorization list is available at xxxxx://xxxx.xxxxxx.xx/xxxxxxxxxxxxx-xxxx

This list is under evaluation by ECHA and may subject to change in the future

3. The table above only shows detected SVHC, and SVHC that below RL are not reported. Please refer to Appendix for the full list of tested SVHC.

4. Testing has been subcontracted Chennai lab.

5. Above all testing has been performed as per customer request.

XXX Xx. : 2348800601 40049443 Page 7 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

APPENDIX

No.	Substance Name	CAS No./ EC No.	RL (%) SCL(%)#	No.	Substance Name	CAS No./ EC No.	RL (%) SCL(%)#
Candidate List of Substances of Very High Concern (SVHC) for authorization published on Oct 28, 2008
1	4,4’-Diaminodiphenylmethane (MDA)ª	101-77-9/ 000-000-0	0.010 / -	2	5-tert-butyl-2,4,6-trinitro-m-xylene (musk xylene)ª	81-15-2/ 000-000-0	0.010 / -
3	Alkanes, C10-13, chloro (Short Chain Chlorinated Paraffins)	00000-00-0/ 000-000-0	0.010 / -	4	Anthracene	120-12-7/ 000-000-0	0.010 / -
5	Benzyl butyl phthalate (BBP)ª	85-68-7/ 000-000-0	0.010 / -	6	Bis(2-ethylhexyl)phthalate (DEHP)ª	117-81-7/ 000-000-0	0.010 / -
7	Bis(tributyltin)oxide (TBTO)	56-35-9/ 000-000-0	0.010 / -	8	Cobalt dichloride*	7646-79-9/ 000-000-0	0.001 / 0.01▼
9	Diarsenic pentaoxide*ª	1303-28-2/ 000-000-0	0.001 / -	10	Diarsenic trioxide*ª	1327-53-3/ 000-000-0	0.001 / -
11	Dibutyl phthalate (DBP)ª	84-74-2/ 000-000-0	0.010 / -	12	Hexabromocyclododecane (HBCDD)	-	0.010 / -
13	Lead hydrogen arsenate*	7784-40-9/ 000-000-0	0.001 / -	14	Sodium dichromate*ª	7789-12-0 00000-00-0/ 000-000-0	0.001 / -
15	Xxxxxxxx xxxxxxxx*	00000-00-0/ 000-000-0	0.001 / -
Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 13, 2010
16	2,4-Dinitrotolueneª	121-14-2/ 000-000-0	0.010 / -	17	Anthracene oil*ª	00000-00-0/ 000-000-0	0.010 / -
18	Anthracene oil, anthracene paste*	00000-00-0/ 000-000-0	0.010 / -	19	Anthracene oil, anthracene paste, anthracene fraction*	00000-00-0/ 000-000-0	0.010 / -
20	Anthracene oil, anthracene paste; distn. Lights*	00000-00-0/ 000-000-0	0.010 / -	21	Anthracene oil, anthracene-low*	00000-00-0/ 000-000-0	0.010 / -
22	Diisobutyl phthalateª	84-69-5/ 000-000-0	0.010 / -	23	Lead chromate molybdate sulfate red (C.I. Pigment Red 104)* ª	00000-00-0/ 000-000-0	0.001 / -
24	Lead chromate*ª	7758-97-6/ 000-000-0	0.001 / -	25	Lead sulfochromate yellow (C.I. Pigment Yellow 34)*ª	1344-37-2/ 000-000-0	0.001 / -
26	Pitch, coal tar, high temp.*ª	00000-00-0/ 000-000-0	0.00025 / 0.00025▼	27	Tris(2-chloroethyl)phosphateª	115-96-8/ 000-000-0	0.010 / -
Candidate List of Substances of Very High Concern (SVHC) for authorization published on Mar 30, 2010
28	Acrylamide	79-06-1/ 000-000-0	0.010 / -
Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 18, 2010
29	Ammonium dichromate*ª	7789-09-5/ 000-000-0	0.001 / -	30	Boric acid*	-	0.001 / -
31	Disodium tetraborate, anhydrous*	1303-96-4 1330-43-4 00000-00-0/ 000-000-0	0.001 / -	32	Potassium chromate*ª	7789-00-6/ 000-000-0	0.001 / -
33	Potassium dichromate*ª	7778-50-9/ 000-000-0	0.001 / -	34	Sodium chromate*ª	7775-11-3/ 000-000-0	0.001 / -

XXX Xx. : 2348800601 40049443 Page 8 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

Tetraboron disodium heptaoxide, hydrate*

00000-00-0/

000-000-0

0.001 /

Trichloroethyleneª

79-01-6/

000-000-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 15, 2010

2-Ethoxyethanol

110-80-5/

000-000-0

0.010 /

2-Methoxyethanol

109-86-4/

000-000-0

0.010 /

Acids generated from chromium trioxide and their oligomers

0.001 /

Chromium trioxide*ª

1333-82-0/

000-000-0

0.001 /

Cobalt(II) carbonate*

513-79-1/

000-000-0

0.001 / 0.01▼

Cobalt(II) diacetate*

71-48-7/

000-000-0

0.001 / 0.01▼

Cobalt(II) dinitrate*

00000-00-0/

000-000-0

0.001 / 0.01▼

Cobalt(II) sulphate*

00000-00-0/

000-000-0

0.001 / 0.01▼

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 20, 2011

1,2,3-Trichloropropane

96-18-4/

000-000-0

0.010 /

1,2-Benzenedicarboxylic acid, di- C6-8-branched alkyl esters, C7- richª

00000-00-0/

000-000-0

0.010 /

1,2-Benzenedicarboxylic acid, di- C7-11-branched and linear alkyl estersª

00000-00-0/

000-000-0

0.010 /

1-Methyl-2-pyrrolidone

872-50-4/

000-000-0

0.010 /

2-Ethoxyethyl acetate

111-15-9/

000-000-0

0.010 /

Hydrazine

7803-57-8

302-01-2/

000-000-0

0.010 /

Strontium chromate*ª

7789-06-2/

000-000-0

0.001 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 19, 2011

1,2-Dichloroethaneª

107-06-2/

000-000-0

0.010 /

2,2'-dichloro-4,4'- methylenedianiline (MOCA)ª

101-14-4/

000-000-0

0.010 /

2-Methoxyaniline

90-04-0/

000-000-0

0.010 /

4-(1,1,3,3-tetramethylbutyl)phenol

140-66-9/

000-000-0

0.010 / 0.025▼

Aluminosilicate Refractory Ceramic Fibres*

0.010 /

Arsenic acid*ª

7778-39-4/

000-000-0

0.001

Bis(2-methoxyethyl) etherª

111-96-6/

000-000-0

0.010 /

Bis(2-methoxyethyl) phthalateª

117-82-8/

000-000-0

0.010 /

Calcium arsenate*

7778-44-1/

000-000-0

0.001 /

Dichromium tris(chromate) *ª

00000-00-0/

000-000-0

0.001 /

Formaldehyde, oligomeric reaction products with aniline (technical MDA)ª

00000-00-0/

000-000-0

0.010 /

Lead diazide*

00000-00-0/

000-000-0

0.001 /

Lead dipicrate*

6477-64-1/

000-000-0

0.001 /

Lead styphnate*

00000-00-0/

000-000-0

0.001 /

N,N-dimethylacetamide (DMAC)

127-19-5/

000-000-0

0.010 /

Pentazinc chromate octahydroxide*ª

00000-00-0/

000-000-0

0.001 /

Phenolphthalein

77-09-8/

000-000-0

0.010 /

Potassium hydroxyoctaoxodizincatedichromat e*ª

00000-00-0/

000-000-0

0.001 /

Trilead diarsenate*

3687-31-8/

000-000-0

0.001 /

Zirconia Aluminosilicate Refractory Ceramic Fibres*

650-017-00-8

(Index no.)

0.001 /

XXX No. : 2348800601 40049443 Page 9 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 18, 2012

[4-[[4-anilino-1-naphthyl][4- (dimethylamino)phenyl]methylene] cyclohexa-2,5-dien-1-ylidene] dimethylammonium chloride (C.I. Basic Blue 26)

2580-56-5/

000-000-0

0.010 /

[4-[4,4'-bis(dimethylamino) benzhydrylidene]cyclohexa-2,5- dien-1-ylidene]dimethylammonium chloride (C.I. Basic Violet 3)

548-62-9/

000-000-0

0.010 /

1,2-bis(2-methoxyethoxy) ethane (TEGDME; triglyme)

112-49-2/

000-000-0

0.010 /

1,2-dimethoxyethane; ethylene glycol dimethyl ether (EGDME)

110-71-4/

000-000-0

0.010 /

4,4'-bis(dimethylamino) benzophenone (Xxxxxxx’x Ketone)

90-94-8/

000-000-0

0.010 /

4,4'-bis(dimethylamino)-4''- (methylamino)trityl alcohol

561-41-1/

000-000-0

0.010 /

Diboron trioxide*

1303-86-2/

000-000-0

0.001 /

Formamide

75-12-7/

000-000-0

0.010 /

Lead(II) bis(methanesulfonate)*

00000-00-0/

000-000-0

0.001 /

N,N,N',N'-tetramethyl-4,4'- methylenedianiline (Michler’s base)

101-61-1/

000-000-0

0.010 /

1,3,5-Tris(oxiran-2-ylmethyl)-1,3,5- triazinane-2,4,6-trione (TGIC)

2451-62-9/

000-000-0

0.010 /

α,α-Bis[4-(dimethylamino)phenyl]-4 (phenylamino)naphthalene-1- methanol (C.I. Solvent Blue 4)

6786-83-0/

000-000-0

0.010 /

1,3,5-tris[(2S and 2R)-2,3-

epoxypropyl]-1,3,5-triazine-2,4,6- (1H,3H,5H)-trione (β-TGIC)

00000-00-0/

000-000-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 19, 2012

[Phthalato(2-)]dioxotrilead *

00000-00-0/

000-000-0

0.001 /

1,2-Benzenedicarboxylic acid, dipentylester, branched and linearª

00000-00-0/

000-000-0

0.010 /

1,2-Diethoxyethane

629-14-1/

000-000-0

0.010 /

1-Bromopropaneª

106-94-5/

000-000-0

0.010 /

3-Ethyl-2-methyl-2-(3-methylbutyl)- 1,3-oxazolidine

143860-04-2/

000-000-0

0.010 /

4-(1,1,3,3-tetramethylbutyl)phenol, ethoxylatedª

0.010 /

4,4'-Methylenedi-o-toluidine

838-88-0/

000-000-0

0.010 /

4,4'-oxydianiline and its salts

0.010 /

4-Aminoazobenzene

60-09-3/

000-000-0

0.010 /

4-Methyl-m-phenylenediamine

95-80-7/

000-000-0

0.010 /

4-Nonylphenol, branched and linear

0.010 /

6-Methoxy-m-toluidine

120-71-8/

000-000-0

0.010 /

Acetic acid, lead salt, basic*

00000-00-0/

000-000-0

0.001 /

Biphenyl-4-ylamine

92-67-1/

000-000-0

0.010 /

Bis(pentabromophenyl) ether (DecaBDE)

1163-19-5/

000-000-0

0.010 /

100

C,C'-azodi(formamide) (ADCA)

123-77-3/

000-000-0

0.010 /

101

Dibutyltin dichloride (DBTC)

683-18-1/

000-000-0

0.010 / 0.01▼

102

Diethyl sulphate

64-67-5/

000-000-0

0.010 /

103

Diisopentylphthalate (DIPP)ª

605-50-5/

000-000-0

0.010 /

104

Dimethyl sulphate

77-78-1/

000-000-0

0.010 / 0.01▼

105

Dinoseb (6-sec-butyl-2,4- dinitrophenol)

88-85-7/

000-000-0

0.010 /

106

Dioxobis(stearato)trilead*

00000-00-0/

000-000-0

0.001 /

107

Fatty acids, C16-18, lead salts*

00000-00-0/

000-000-0

0.001 /

108

Furan

110-00-9/

000-000-0

0.010 /

XXX Xx. : 2348800601 40049443 Page 10 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

109

Henicosafluoroundecanoic acid

2058-94-8/

000-000-0

0.010 /

110

Heptacosafluorotetradecanoic acid

376-06-7/

000-000-0

0.010 /

111

Cyclohexane-1,2-dicarboxylic anhydride

0.010 /

112

Hexahydromethylphthalic anhydride

0.010 /

113

Lead bis(tetrafluoroborate)*

00000-00-0/

000-000-0

0.001 /

114

Lead cyanamidate*

00000-00-0/

000-000-0

0.001 /

115

Lead dinitrate*

00000-00-0/

000-000-0

0.001 /

116

Lead monoxide*

1317-36-8/

000-000-0

0.001 /

117

Lead oxide sulphate*

00000-00-0/

000-000-0

0.001 /

118

Lead tetroxide*

1314-41-6/

000-000-0

0.001 /

119

Lead titanium trioxide*

00000-00-0/

000-000-0

0.001 /

120

Lead titanium zirconium oxide*

00000-00-0/

000-000-0

0.001 /

121

Methoxyacetic acid

625-45-6/

000-000-0

0.010 /

122

N,N-Dimethylformamide

68-12-2/

000-000-0

0.010 /

123

N-Methylacetamide

79-16-3/

000-000-0

0.010 /

124

N-Pentyl-isopentylphthalateª

776297-69-9

0.010 /

125

o-Aminoazotoluene

97-56-3/

000-000-0

0.010 /

126

o-Toluidine

95-53-4/

000-000-0

0.010 /

127

Pentacosafluorotridecanoic acid

00000-00-0/

000-000-0

0.010 /

128

Pentalead tetraoxide sulphate*

00000-00-0/

000-000-0

0.001 /

129

Methyloxirane (Propylene oxide)

75-56-9/

000-000-0

0.010 /

130

Pyrochlore, antimony lead yellow*

8012-00-8/

000-000-0

0.001 /

131

Silicic acid, barium salt, lead- doped*

00000-00-0/

000-000-0

0.001 /

132

Silicic acid, lead salt*

00000-00-0/

000-000-0

0.001 /

133

Sulfurous acid, lead salt, dibasic*

00000-00-0/

000-000-0

0.001 /

134

Tetraethyllead*

78-00-2/

000-000-0

0.001 /

135

Tetralead trioxide sulphate*

00000-00-0/

000-000-0

0.001 /

136

Tricosafluorododecanoic acid

307-55-1/

000-000-0

0.010 /

137

Trilead bis(carbonate)dihydroxide*

1319-46-6/

000-000-0

0.001 /

138

Trilead dioxide phosphonate*

00000-00-0/

000-000-0

0.001 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 20, 2013

139

4-Nonylphenol, branched and linear, ethoxylatedª

0.010 /

140

Ammoniumpentadecafluoro octanoate (APFO)

3825-26-1/

000-000-0

0.010 /

141

Cadmium

7440-43-9/

000-000-0

0.001 /

142

Cadmium oxide*

1306-19-0/

000-000-0

0.001 /

143

Dipentyl phthalate (DPP)ª

131-18-0/

000-000-0

0.010 /

144

Pentadecafluorooctanoic acid (PFOA)

335-67-1/

000-000-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 16, 2013

145

Cadmium sulphide*

1306-23-6/

000-000-0

0.001 /

146

Dihexyl phthalate

84-75-3/

000-000-0

0.010 /

147

Disodium 3,3'-[[1,1'-biphenyl]-4,4'- diylbis(azo)]bis(4- aminonaphthalene-1-sulphonate) (C.I. Direct Red 28)

573-58-0/

000-000-0

0.010 /

148

Disodium 4-amino-3-[[4'-[(2,4- diaminophenyl)azo][1,1'-biphenyl]- 4-yl]azo]-5-hydroxy-6- (phenylazo)naphthalene-2,7- disulphonate (C.I. Direct Black 38)

1937-37-7/

000-000-0

0.010 /

XXX No. : 2348800601 40049443 Page 11 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

149

Imidazolidine-2-thione; 2-imidazoline-2-thiol

96-45-7/

000-000-0

0.010 /

150

Lead di(acetate)*

301-04-2/

000-000-0

0.001 /

151

Trixylyl phosphate

00000-00-0/

000-000-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 16, 2014

152

1,2-Benzenedicarboxylic acid, dihexyl ester, branched and linear

00000-00-0/

000-000-0

0.010 /

153

Cadmium chloride*

00000-00-0/

000-000-0

0.001 / 0.01▼

154

Sodium perborate; perboric acid, sodium salt*

0.001 /

155

Sodium peroxometaborate*

7632-04-4/

000-000-0

0.001 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 17, 2014

156

2-benzotriazol-2-yl-4,6-di-tert- butylphenol (UV-320)

3846-71-7 /

000-000-0

0.010 /

157

2-(2H-benzotriazol-2-yl)-4,6- ditertpentylphenol (UV-328)

00000-00-0 / 247-

384-8

0.010 /

158

2-ethylhexyl 10-ethyl-4,4-dioctyl-7- oxo-8-oxa-3,5-dithia-4- stannatetradecanoate; DOTE

00000-00-0 /

000-000-0

0.010 /

159

Reaction mass of 2-ethylhexyl 10- ethyl-4,4-dioctyl-7-oxo-8-oxa-3,5- dithia-4-stannatetradecanoate and 2-ethylhexyl 10-ethyl-4-[[2-[(2- ethylhexyl)oxy]-2-oxoethyl]thio]-4- octyl-7-oxo-8-oxa-3,5-dithia-4- stannatetradecanoate (reaction mass of DOTE and MOTE)

0.010 /

160

Cadmium fluoride*

7790-79-6 /

000-000-0

0.001 / 0.01▼

161

Cadmium sulphate*

00000-00-0;

00000-00-0 / 233-

331-6

0.001 / 0.01▼

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun15, 2015

162

1,2-benzenedicarboxylic acid, di- C6-10-alkyl esters or mixed decyl and hexyl and octyl diesters

0.010 /

163

5-sec-butyl-2-(2,4- dimethylcyclohex-3-en-1-yl)-5- methyl-1,3-dioxane [1], 5-sec- butyl-2-(4,6-dimethylcyclohex-3- en-1-yl)-5-methyl-1,3-dioxane [2] [covering any of the individual stereoisomers of [1] and [2] or any combination thereof]

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Dec 17, 2015,

164

1,3-propanesultone

1120-71-4 /

000-000-0

0.010 / 0.01▼

165

2,4-di-tert-butyl-6-(5- chlorobenzotriazol-2-yl)phenol (UV-327)

3864-99-1 / 223-

383-8

0.010 /

166

2-(2H-benzotriazol-2-yl)-4-(tert- butyl)-6-(sec-butyl)phenol (UV- 350)

00000-00-0 /

000-000-0

0.010 /

167

Nitrobenzene

98-95-3 / 202-716-

0.010 /

168

Perfluorononan-1-oic-acid and its sodium and ammonium salts (PFNA)

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 20, 2016

169

Benzo[def]chrysene (Benzo[a]pyrene)

50-32-8 / 200-

028-5

0.010 / 0.01▼

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 12, 2017

XXX No. : 2348800601 40049443 Page 12 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

170

4,4’-Isopropylidenediphenol (Bisphenol A)

80-05-7 / 201-

245-8

0.010 /

171

4-Heptylphenol, branched and linear

0.010 /

172

Nonadecafluorodecanoic acid (PFDA) and its sodium and ammonium salts

0.010 /

173

p-(1,1-dimethylpropyl)phenol

80-46-6 / 201-280-

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jul 7, 2017

174

Perfluorohexane-1-sulphonic acid and its salts

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 15, 2018

175

Benz[a]anthracene

56-55-3; 1718-

53-2/ 000-000-0

0.010 /

176

Cadmium carbonate*

513-78-0/

000-000-0

0.001 /

177

Cadmium hydroxide*

00000-00-0/

000-000-0

0.001 /

178

Cadmium nitrate*

00000-00-0/ 233-

710-6

0.001 / 0.01▼

179

Chrysene

218-01-9; 1719-

03-5/ 000-000-0

0.010 /

180

1,6,7,8,9,14,15,16,17,17,18,18-

Dodecachloropentacyclo [12.2.1.16,9.02,13.05,10]

octadeca-7,15-diene (“Dechlorane Plus”™)

0.010 /

181

Reaction products of 1,3,4- thiadiazolidine-2,5-dithione, formaldehyde and 4-heptylphenol, branched and linear (RP-HP)

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 27, 2018

182

Benzene-1,2,4-tricarboxylic acid 1,2 anhydride (TMA)

552-30-7 / 209-

008-0

0.010 /

183

Benzo[ghi]perylene

191-24-2 /

000-000-0

0.010 /

184

Decamethylcyclopentasiloxane (D5)

541-02-6 / 208-

764-9

0.010 /

185

Dicyclohexyl phthalate (DCHP)

84-61-7 / 201-545-

0.010 /

186

Disodium octaborate*

00000-00-0 /

000-000-0

0.001 /

187

Dodecamethylcyclohexasiloxane (D6)

540-97-6 / 208-

762-8

0.010 /

188

Ethylenediamine (EDA)

107-15-3 / 203-

468-6

0.010 /

189

Lead

7439-92-1 / 231-

100-4

0.001 / 0.03▼

190

Octamethylcyclotetrasiloxane (D4)

556-67-2 / 209-

136-7

0.010 /

191

Terphenyl, hydrogenated

00000-00-0 / 262-

967-7

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 15, 2019

192

2,2-Bis(4'-hydroxyphenyl)-4- methylpentane

6807-17-6 /

000-000-0

0.010 /

193

Benzo[k]fluoranthene

207-08-9 /

000-000-0

0.010 /

194

Fluoranthene

206-44-0 / 205-

912-4

0.010 /

195

Phenanthrene

85-01-8 / 201-581-

0.010 /

196

Pyrene

129-00-0 / 204-

927-3

0.010 /

197

1,7,7-trimethyl-3- (phenylmethylene)bicyclo[2.2.1]he ptan-2-one

00000-00-0 / 239-

139-9

0.010

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jul 16, 2019

198

2,3,3,3-Tetrafluoro-2- (heptafluoropropoxy)propionic acid, its salts and its acyl halides

0.010 /

199

2-Methoxyethyl acetate

110-49-6 /

000-000-0

0.010 /

XXX Xx. : 2348800601 40049443 Page 13 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096 ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

200

Tris(4-nonylphenyl, branched and linear) phosphite (TNPP) with ≥ 0.1% w/w of 4-nonylphenol, branched and linear (4-NP)

0.010 /

201

4-tert-butylphenol

98-54-4 /

000-000-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 16, 2020

202

2-benzyl-2-dimethylamino-4'- morpholinobutyrophenone

119313-12-1 /

000-000-0

0.010 /

203

2-methyl-1-(4-methylthiophenyl)-2- morpholinopropan-1-one

00000-00-0 / 400-

600-6

0.010 /

204

Diisohexyl phthalate

00000-00-0 /

000-000-0

0.010 /

205

Perfluorobutane sulfonic acid (PFBS) and its salts

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 25, 2020

206

1-Vinylimidazole

1072-63-5 /

000-000-0

0.010 / 0.03▼

207

2-Methylimidazole

693-98-1 /

000-000-0

0.010 /

208

Butyl 4-hydroxybenzoate

94-26-8 / 202-

318-7

0.010 /

209

Dibutylbis(pentane-2,4-dionato- O,O')tin

00000-00-0 / 245-

152-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 19, 2021

210

Bis(2-(2-

methoxyethoxy)ethyl)ether

143-24-8 / 205-

594-7

0.010 /

211

Dioctyltin dilaurate, stannane, dioctyl-, bis(coco acyloxy) derivs., and any other stannane, dioctyl-, bis(fatty acyloxy) derivs. wherein C12 is the predominant carbon number of the fatty acyloxy moiety

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jul 8, 2021

212

1,4-dioxane

123-91-1 / 204-

661-8

0.010 /

213

2,2-bis(bromomethyl)propane-1,3- diol (BMP); 2,2-dimethylpropan-1- ol, tribromo derivative/3-bromo- 2,2-bis(bromomethyl)-1-propanol (TBNPA); 2,3-dibromo-1-propanol (2,3-DBPA)

0.010 /

214

2-(4-tert- butylbenzyl)propionaldehyde and its individual stereoisomers

0.010 /

215

4,4'-(1-

methylpropylidene)bisphenol

77-40-7 / 201-025-

0.010 /

216

Glutaral

111-30-8 / 203-

856-5

0.010 /

217

Medium-chain chlorinated paraffins (MCCP)

0.010 /

218

Orthoboric acid, sodium salt

0.001 /

219

Phenol, alkylation products (mainly in para position) with C12-rich branched or linear alkyl chains from oligomerisation, covering any individual isomers and/ or combinations thereof (PDDP)

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 17, 2022

220

(±)-1,7,7-trimethyl-3-[(4- methylphenyl)methylene]bicyclo[2. 2.1]heptan-2-one covering any of the individual isomers and/or combinations thereof (4-MBC)

0.010 /

221

6,6'-di-tert-butyl-2,2'-methylenedi- p-cresol (DBMC)

119-47-1 / 204-

327-1

0.010 /

XXX Xx. : 2348800601 40049443 Page 14 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:14

48001096

ISSUE DATE: 14th March, 2023

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

No.

Substance Name

CAS No./ EC No.

RL (%) SCL(%)#

222

S-(tricyclo[5.2.1.0'2,6]deca-3-en- 8(or 9)-yl) O-(isopropyl or isobutyl or 2-ethylhexyl) O-(isopropyl or isobutyl or 2-ethylhexyl) phosphorodithioate

255881-94-8 /

000-000-0

0.010 /

223

tris(2-methoxyethoxy)vinylsilane

1067-53-4 / 213-

934-0

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jun 10, 2022

224

N-(hydroxymethyl)acrylamide

924-42-5 / 213-

103-2

0.010 /

Candidate List of Substances of Very High Concern (SVHC) for authorization published on Jan 17, 2023

225

1,1'-[ethane-1,2-diylbisoxy]bis[2,4,6- tribromobenzene]

00000-00-0 /

000-000-0

0.010 /

226

2,2',6,6'-tetrabromo-4,4'- isopropylidenediphenol

79-94-7 / 201-236-

0.010 /

227

4,4'-sulphonyldiphenol

80-09-1 / 201-

250-5

0.010 /

228

Barium diboron tetraoxide

00000-00-0 / 237-

222-4

0.001 /

229

Bis(2-ethylhexyl) tetrabromophthalate covering any of the individual isomers and/or combinations thereof

0.010 /

230

Isobutyl 4-hydroxybenzoate

4247-02-3 / 224-

208-8

0.010 /

231

Melamine

108-78-1 / 203-

615-4

0.010 /

232

Perfluoroheptanoic acid and its salts

0.010 /

233

reaction mass of 2,2,3,3,5,5,6,6- octafluoro-4-(1,1,1,2,3,3,3- heptafluoropropan-2-yl)morpholine and 2,2,3,3,5,5,6,6-octafluoro-4- (heptafluoropropyl)morpholine

- / 000-000-0

0.010 /

XXX No. : 2348800601 40049443 Page 15 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

TEST REPORT

Report No. : MAN:HL:1448001096

ISSUE DATE: 14th March, 2023

Sample as Received

***** END OF REPORT*****

XXX Xx. : 2348800601 40049443 Page 16 of 16 Control No.:1448501644

Connectivity and Products, Testing Laboratory, Plot no. 00, Xxxxxx 0, XXX Xxxxxxx, Xxxxxxxx Xxxxxxxx, Xxxxxxx- 000000 (Xxxxx) t: (x00-000 000 0000

SGS India Pvt. Ltd xxx.xxx.xxx

Member of the SGS Group (SGS SA)

Document Metadata

Table of Contents

Produkt Kumlokk og Rammer, VOTEC Kabelkummer

Document Metadata