Unbundled Copper Loop – Non-Designed (UCL-ND 2.4.3.1 The UCL–ND is provisioned as a dedicated 2-wire metallic transmission facility from BellSouth’s Main Distribution Frame (MDF) to a customer’s premises (including the NID). The UCL-ND will be a “dry copper” facility in that it will not have any intervening equipment such as load coils, repeaters, or digital access main lines (DAMLs), and may have up to 6,000 feet of bridged tap between the End User’s premises and the serving wire center. The UCL-ND typically will be 1300 Ohms resistance and in most cases will not exceed 18,000 feet in length, although the UCL-ND will not have a specific length limitation. For Loops less than 18,000 feet and with less than 1300 Ohms resistance, the Loop will provide a voice grade transmission channel suitable for Loop start signaling and the transport of analog voice grade signals. The UCL-ND will not be designed and will not be provisioned with either a DLR or a test point.
Unbundled Copper Sub-Loop (UCSL) is a copper facility of any length provided from the cross-box in the field up to and including the End User’s point of demarcation. If available, this facility will not have any intervening equipment such as load coils between the End User and the cross-box.
Unbundled Copper Loops (UCL) 2.4.1 BellSouth shall make available Unbundled Copper Loops (UCLs). The UCL is a copper twisted pair Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters) and is not intended to support any particular telecommunications service. The UCL will be offered in two types – Designed and Non-Designed.
Special and Differential Treatment for the Newer Asean Member States In order to increase the benefits of this Agreement for the newer ASEAN Member States, and in accordance with the objectives and principles set out in the Preamble and Articles 1 (Objective) and 2 (Guiding Principles), Member States recognise the importance of according special and differential treatment to the newer ASEAN Member States, through:
Power Factor Design Criteria (Reactive Power A wind generating plant shall maintain a power factor within the range of 0.95 leading to 0.95 lagging, measured at the Point of Interconnection as defined in this LGIA, if the ISO’s System Reliability Impact Study shows that such a requirement is necessary to ensure safety or reliability. The power factor range standards can be met using, for example without limitation, power electronics designed to supply this level of reactive capability (taking into account any limitations due to voltage level, real power output, etc.) or fixed and switched capacitors if agreed to by the Connecting Transmission Owner for the Transmission District to which the wind generating plant will be interconnected, or a combination of the two. The Developer shall not disable power factor equipment while the wind plant is in operation. Wind plants shall also be able to provide sufficient dynamic voltage support in lieu of the power system stabilizer and automatic voltage regulation at the generator excitation system if the System Reliability Impact Study shows this to be required for system safety or reliability.
Unbundled Copper Loop – Designed (UCL-D) 2.4.2.1 The UCL-D will be provisioned as a dry copper twisted pair (2- or 4-wire) Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters).
Change of Control of the Academy Trust 102A) The Secretary of State may at any time by notice in writing, subject to clause 102C) below, terminate this Agreement forthwith (or on such other date as he may in his absolute discretion determine) in the event that there is a change:
Unbundled Copper Loop Designed (UCL-D)
Special Permit from Relevant Ministerial/ Government Agencies and Foreign Capital Ownership Limitation Raw Material for Explosives (Ammonium Nitrate) with maximum foreign equity ownership of 49% and a special permit from the Minister of Defense (ISIC 2411) Industry of explosive materials and its components for industry need with maximum foreign equity ownership of 49% and a special permit from the Minister of Defense (ISIC 2429) Sugar Industry (Xxxxx Xxxxxxx Sugar, Refined Crystal Sugar and Raw Crystal Sugar) with maximum foreign equity ownership of 95% and a special permit from the Minister of Industry and the Minister of Agriculture, and it has to be integrated with the sugar plantation. The manufacturing of raw crystal sugar is required for any sugar manufacturer with sugarcane input capacity exceeding 8000 tons per day (ISIC 1542) Processing of plantation product industry (similar capacity or exceeding a certain capacity, according to Regulation of Minister of Agriculture Number 26 of 2007 with maximum foreign capital ownership of 95% with a special permit from Minister of Agriculture. - Fiber and Seed Cotton Industry (ISIC1514, 1711) - Crude oil industry (edible oil) from vegetable and animal, coconut oil industry, palm oil industry, rubber to be sheet, thick latex, crumb rubber industry, raw castor oil industry, sugar, sugar cane and sugar cane residue industry, black tea/green tea industry, dry tobacco leaves industry, Copra, Fiber, Coconut Charcoal, Dust, Nata de coco industry, Coffee sorting, cleaning and peeling industry, Cocoa cleaning, peeling and drying industry, cleaning and peeling seed other than coffee and cacao industry, cashew to be dry seed cashew and Cashew Nut Shell Liquid (CNSL) Industry, Peppercorn to be dry white pepper and dry black pepper industry (ISIC 1514, 2429, 1542, 1549, 1600, 2519, 1531)
Voice Grade Unbundled Copper Sub-Loop Unbundled Sub-Loop Distribution – Intrabuilding Network Cable (aka riser cable)
