API A. Reliant shall supply to Cardinal Health for Manufacturing and Packaging, at Reliant’s sole cost, the API and applicable reference standards in quantities sufficient to meet Reliant’s requirements for each Product as further set forth in Article 4. Prior to delivery of any of the API or reference standard to Cardinal Health for Manufacturing and Packaging, Reliant shall provide to Cardinal Health a copy of the API Material Safety Data Sheet (“MSDS”), as amended, and any subsequent revisions thereto. Reliant shall supply the API, reference standards, and Certificate of Analysis FOB the Facility no later than thirty (30) days before the scheduled Manufacture Date upon which such API will be used by Cardinal Health. Upon receipt of the API, Cardinal Health shall conduct identification testing of the API. Cardinal Health shall use the API solely and exclusively for Manufacturing and Packaging under this Agreement. The maximum volume of API that Reliant supplies to Cardinal Health shall not exceed the amount reflected in the Firm Commitment and the next six (6) months of the Rolling Forecast.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.
TECHNICAL SUPPORT SERVICES 2.1 The technical support services (the "Services"): Party A agrees to provide to Party B the relevant services requested by Party B, which are specified in Exhibit 1 attached hereto ("Exhibit 1").
Supplier shall exercise reasonable care in carrying out the provisions of this Agreement, but shall be kept indemnified by, and shall be without liability to CMA and/or any Fund for any action taken or omitted by it in good faith without negligence including, without limitation, acting in accordance with any Proper Instruction. Supplier shall be entitled to rely on and may act upon the advice of counsel (who may be counsel for CMA or any Fund) on all matters arising in connection with the Services. At any time, Supplier may apply to any officer of CMA or a Fund for instructions and may consult with outside counsel for CMA or the applicable Fund or the independent auditors for the Fund at the expense of the Fund, or other individuals designated in writing by CMA or the Fund, for advice with respect to any matter arising in connection with the Services. Supplier shall not be liable, and shall be indemnified by each Fund or CMA, as applicable, for any action taken or omitted by it in good faith in reliance upon any such instructions or advice or upon any paper or document believed by it to be genuine and to have been signed by such officers or individuals. Supplier shall not be held to have notice of any change of authority of any officer or individual until receipt of written notice thereof from the Fund or CMA. Nothing in this Section shall be construed as imposing upon Supplier any obligation to seek such instructions or advice. Without in any way limiting the generality of the foregoing, Supplier shall in no event be liable for any loss or damage arising from causes beyond its control including, without limitation, delay or cessation of services hereunder or any damages to CMA or a Fund resulting therefrom as a result of work stoppage, power or other mechanical failure, natural disaster, governmental action, communication disruption or other impossibility of performance.
Products and Services Part 2.9(a) of the Disclosure Schedule accurately identifies and describes each Company Product currently being designed, developed, manufactured, marketed, distributed, provided, licensed, or sold by the Company.
Shipment If any of the Major Components associated with any Unit is not Shipped on or before (with the prior approval of the Buyer) the Scheduled Major Component Shipment Date set forth in Attachment 1 for reasons attributable to the Seller and not excused elsewhere in this Contract, the Seller shall pay as liquidated damages, and not as a penalty, a sum calculated in accordance with the table below for each Unit for each day of delay after the Scheduled Major Component Shipment Date as set forth in Attachment 1 until actual Shipment of the last Major Component for such Unit: Days after Scheduled Major Component Shipment Date Liquidated Damages (per day or partial day) *** *** *** *** *** *** Such liquidated damages, if any, shall be computed based on the date of Shipment of the last Major Component for a given Unit and such computations shall disregard any part of or accessory to the Major Component which may be shipped separately and arrive later unless such part of or accessory to the Major Component is necessary for the installation of the Major Component.
Supply of Materials Unless the parties otherwise agree in a Work Order, Manufacturer will supply, in accordance with the relevant approved raw material specifications, all materials to be used by Manufacturer in the performance of Services under a Work Order other than the Rhythm Materials specified in such Work Order. Rhythm or its designees will provide Manufacturer with the Rhythm Materials. Manufacturer agrees (a) to account for all Rhythm Materials, (b) not to provide Rhythm Materials to any third party (other than an Affiliate acting as a permitted subcontractor) without the express prior written consent of Rhythm, (c) not to use Rhythm Materials for any purpose other than conducting the Services, including, without limitation, not to analyze, characterize, modify or reverse engineer any Rhythm Materials or take any action to determine the structure or composition of any Rhythm Materials unless required * CONFIDENTIAL TREATMENT REQUESTED. OMITTED PORTIONS FILED WITH THE SECURITIES AND EXCHANGE COMMISSION PURSUANT TO RULE 406 PROMULGATED UNDER THE SECURITIES ACT OF 1933, AS AMENDED. pursuant to a signed Work Order, and (d) to destroy or return to Rhythm all unused quantities of Rhythm Materials according to Rhythm’s written directions.
Supply of Products TheraSense shall be responsible for the ------------------ manufacture of FreeStyle Products for sale to Nipro.
Accuracy of Orders; Customer Signatures You shall be responsible for the accuracy, timeliness and completeness of any orders transmitted by you on behalf of your customers by any means, including wire or telephone. In addition, you agree to guarantee the signatures of your customers when such guarantee is required by the Company and you agree to indemnify and hold harmless all persons, including us and the Funds’ transfer agent, from and against any and all loss, cost, damage or expense suffered or incurred in reliance upon such signature guarantee.
