Revenue Metering The Connecting Transmission Owner’s revenue metering will be located on the generator side of the 115kV breaker at the Xxxxx Solar Collector Substation and will consist of: • three (3) combination current/voltage transformer (“CT/VT”) units (manufacturer and model ABB/Xxxxxxx KXM-550, GE Grid Solutions KOTEF 000.XX, or other equivalent specified by Connecting Transmission Owner); and • one (1) revenue meter. The ratios of the CTs and VTs will be provided by Connecting Transmission Owner upon its review of the Interconnection Customer’s design documents. (Note: Connecting Transmission Owner’s revenue metering CTs and VTs cannot be used to feed the Interconnection Customer’s check meter.) SERVICE AGREEMENT NO. 2556
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Power Factor Design Criteria Developer shall design the Large Generating Facility to maintain an effective power delivery at demonstrated maximum net capability at the Point of Interconnection at a power factor within the range established by the Connecting Transmission Owner on a comparable basis, until NYISO has established different requirements that apply to all generators in the New York Control Area on a comparable basis. The Developer shall design and maintain the plant auxiliary systems to operate safely throughout the entire real and reactive power design range. The Connecting Transmission Owner shall not unreasonably restrict or condition the reactive power production or absorption of the Large Generating Facility in accordance with Good Utility Practice.
Compatibility 1. Any unresolved issue arising from a mutual agreement procedure case otherwise within the scope of the arbitration process provided for in this Article and Articles 25A to 25G shall not be submitted to arbitration if the issue falls within the scope of a case with respect to which an arbitration panel or similar body has previously been set up in accordance with a bilateral or multilateral convention that provides for mandatory binding arbitration of unresolved issues arising from a mutual agreement procedure case.
Geometric visibility The visibility of the illuminating surface, including its visibility in areas which do not appear to be illuminated in the direction of observation considered, shall be ensured within a divergent space defined by generating lines based on the perimeter of the illuminating surface and forming an angle of not less than 5° with the axis of reference of the headlamp. The origin of the angles of geometric visibility is the perimeter of the projection of the illuminating surface on a transverse plane tangent to the foremost part of the lens of the headlamp.
Commodity Compliance and Compatibility It is the Contractor’s responsibility to ensure that the Commodities supplied are compliant with the Contract requirements, specifications, terms, and conditions. Additionally, the Contractor shall ensure that all Commodities ordered by the Customer are fully compatible with each other and with any associated pre-existing Commodity possessed by the Customer and disclosed to the Contractor by the Customer. The Contractor’s acceptance of the Customer’s order shall indicate that the Contractor agrees to deliver a Commodity that is fully compliant and compatible with the Customer’s order requirements, specifications, terms, and conditions. In the event any ordered Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components are found by the Customer to be missing, incorrect, defective, damaged, non- compatible, or non-compliant, the Contractor shall, at the Customer’s discretion, be required to complete one of the following: • Install or repair the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s), and their respective features, equipment, and components; • Replace the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components; • Refund the purchase price of the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components to the Customer. Any changes necessary after the delivery of the Customer’s order that are required to bring a Commodity into compliance or compatibility due to an incorrect order fulfillment by the Contractor shall be accomplished at the Contractor’s expense.
Financial Viability and Regulatory Compliance 4.6.1 The Contractor warrants and represents that its corporate entity is in good standing with all applicable federal, state, and local licensing authorities and that it possesses all requisite licenses to perform the services required by this contract. The Contractor further warrants and represents that it owes no outstanding delinquent federal, state, or local taxes or business assessments.
Fire Fighting Costs of operating and maintaining the fire-fighting equipments and personnel, if any.
Infrastructure Vulnerability Scanning Supplier will scan its internal environments (e.g., servers, network devices, etc.) related to Deliverables monthly and external environments related to Deliverables weekly. Supplier will have a defined process to address any findings but will ensure that any high-risk vulnerabilities are addressed within 30 days.
Local Circuit Switching Capability, including Tandem Switching Capability 4.2.1 Local circuit switching capability is defined as: (A) line-side facilities, which include, but are not limited to, the connection between a loop termination at a main distribution frame and a switch line card; (B) trunk-side facilities, which include, but are not limited to, the connection between trunk termination at a trunk-side cross-connect panel and a switch trunk card; (C) switching provided by remote switching modules; and (D) all features, functions, and capabilities of the switch, which include, but are not limited to: (1) the basic switching function of connecting lines to lines, line to trunks, trunks to lines, and trunks to trunks, as well as the same basic capabilities made available to BellSouth’s customers, such as a telephone number, white page listings, and dial tone; and (2) all other features that the switch is capable of providing, including but not limited to customer calling, customer local area signaling service features, and Centrex, as well as any technically feasible customized routing functions provided by the switch. Any features that are not currently available but are technically feasible through the switch can be requested through the BFR/NBR process.
