Common use of Conformity of production Clause in Contracts

Conformity of production. 8.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 13 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

AutoNDA by SimpleDocs

Conformity of production. 8.17.1. Procedures concerning for the conformity of production shall comply with those set out conform to the general provisions defined in the 1958 Agreement, Article 2 and Schedule 1 to the Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.27.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.37.3. The Type Approval Authority approval authority which has granted the approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 11 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.3Rev.2) and meet with the following requirements: 8.28.1. A vehicle Vehicles approved pursuant according to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 5. 6.2 above;. 8.38.2. The Type Approval Authority authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 11 contracts

Samples: Uniform Technical Prescriptions Agreement, Uniform Technical Prescriptions Agreement, Uniform Technical Prescriptions Agreement

Conformity of production. 8.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in Appendix 2 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/324-E/ECE/TRANS/505/Rev.3Rev.2) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 6 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet with the following requirements: 8.216.1. A vehicle approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 514. above;. 8.316.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once every two years.

Appears in 6 contracts

Samples: Consolidated Version of R28 Up to Amendment 6, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Equipment and Parts

Conformity of production. 8.111.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.211.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. abovethis regulation; 8.311.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 6 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.27.1. A vehicle Vehicles, bodywork and fire suppression systems approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 5. above;. 8.37.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to each production unitfacility. The normal frequency of such inspections these verifications shall be once every per two years.

Appears in 5 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.111.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.211.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. abovethis Regulation; 8.311.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 5 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.28.1. A vehicle Vehicles/components approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above;the relevant part(s) of this Regulation. 8.38.2. The Type Approval Authority which that has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 5 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning for the conformity of production shall comply with those set out conform to the general provisions defined in Article 2 and Schedule 1 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted the approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 4 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.28.1. A vehicle Tyres approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved approved, by meeting the requirements of set forth in paragraph 56. above;. 8.38.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The For each production facility, the normal frequency of such inspections these verifications shall be once every two years.

Appears in 4 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.137.1. Procedures concerning The conformity of production procedure shall comply with those the requirements set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/TRANS/505/ Rev.3) and meet the following requirements:). 8.237.2. A Every vehicle approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set out in paragraph 535. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 4 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.3) and meet Rev.2), with the following requirements: 8.27.1. A vehicle Vehicles and bodyworks approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 5. above;. 8.37.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to each production unitfacility. The normal frequency of such inspections these verifications shall be once every per two years.

Appears in 4 contracts

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.17.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.27.2. A For each type of vehicle approved pursuant to or component the tests prescribed in the relevant part(s) of this Regulation shall be so manufactured as to conform to carried out on a statistically controlled and random basis, in accordance with one of the type approved by meeting the requirements of paragraph 5. aboveregular quality assurance procedures; 8.37.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 4 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning for the conformity of production shall comply with those set out conform to the general provisions defined in Article 2 and Schedule 1 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above;. 8.3. The Type Approval Authority which has granted the approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 3 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations

Conformity of production. 8.1. Procedures concerning for the conformity of production shall comply with those set out conform to the general provisions defined in the 1958 Agreement, Article 2 and Schedule 1 to the Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted the approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 3 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations

Conformity of production. 8.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph Paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 3 contracts

Samples: Regulation on Uniform Provisions Concerning the Approval of Motor Vehicles, Regulation on Uniform Provisions Concerning the Approval of Motor Vehicles, Regulation on Uniform Provisions Concerning the Approval of Motor Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.217.1. A Every vehicle approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set out in paragraph 516. above;. 8.317.2. The Type Approval Authority which that has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.17.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in the 1958 Agreement, Article 2 and Schedule 1 to the Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.27.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above.; 8.37.3. The Type Approval Authority which has granted the approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.28.1. A vehicle Every rear underrun protective device approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set out in paragraph 57. above;. 8.38.2. The Type Approval Authority which that has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

AutoNDA by SimpleDocs

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.3) and meet Rev. 2), with the following requirements: 8.28.1. A vehicle Tyres approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved approved, by meeting the requirements of set forth in paragraph 56. above;. 8.38.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The For each production facility, the normal frequency of such inspections these verifications shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet with the following requirements: 8.28.1. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 5. above; 8.38.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet with the following requirements: 8.28.1. A vehicle Vehicles approved pursuant according to this Regulation shall be manufactured so manufactured as to conform to the type approved by meeting and satisfy the requirements of set forth in paragraph 56.2. above; 8.38.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in Appendix 2 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/324‑E/ECE/TRANS/505/Rev.3Rev.2) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.28.1. A vehicle The tyres approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 56. above;. 8.38.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The For each production facility, the normal frequency of such inspections these verifications shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.17.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) ), and meet the following requirements: 8.27.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.37.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.226.1. A Every vehicle approved pursuant to under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set out in paragraph 525. above;. 8.326.2. The Type Approval Authority which that has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once one every two years.

Appears in 2 contracts

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in the 1958 Agreement, Article 2 and Schedule 1 to the Agreement (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.3Rev.2) and meet with the following requirements: 8.211.1. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph set forth in paragraphs 5., 6. and 7. above;. 8.311.2. The Type Approval Authority which has granted type approval may at any time verify the conformity of control methods applicable to applied in each production unitfacility. The normal frequency of such inspections these verifications shall be once every two years.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.17.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in Appendix 2 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/324-E/ECE/TRANS/505/Rev.3Rev.2) and meet the following requirements: 8.27.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.37.3. The Type Approval competent Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet ), with the following requirements: 8.27.1. A Every vehicle approved pursuant bearing an approval mark as prescribed under this Regulation shall conform to the vehicle type approved, more particularly as regards the arrangement of foot controls; 7.2. In order to verify conformity as prescribed in paragraph 7.1. above, a sufficient number of serially-produced vehicles bearing the approval mark required by this Regulation shall be so manufactured as subjected to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two yearsrandom checks.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles

Conformity of production. 8.1. Procedures concerning The conformity of production procedures shall comply with those set out in the 1958 Agreement, Schedule 1 Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.3) and meet Rev.2), with the following requirements: 8.27.1. A vehicle Vehicles and bodyworks approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of set forth in paragraph 5. above;. 8.37.2. The Type Approval Competent Authority which has granted approval Type-Approval may at any time verify the conformity of control methods applicable to each production unitfacility. The normal frequency of such inspections these verifications shall be once every per two years.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Conformity of production. 8.17.1. Procedures concerning conformity of production shall comply with those set out conform to the general provisions defined in Appendix 2 to the 1958 Agreement, Schedule 1 Agreement (E/ECE/324-E/ECE/TRANS/505/Rev.3Rev.2) and meet the following requirements: 8.27.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.37.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

Appears in 1 contract

Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!