Common use of Conformity of production Clause in Contracts

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity Conformity of production Production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.112.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 67. and 79. above. 9.212.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 6 to this Regulation shall be complied with. 9.312.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.412.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 6 to this Regulation regulation shall be complied with. 9.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 6 to this Regulation regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 Schedule 1 (E/ECE/324-E/ECE/TRANS/505/Rev.2) Rev.3), with the following requirements: 9.18.1. Headlamps approved under this Regulation Retro-reflectors shall be so manufactured as to conform to the type approved by meeting under this Regulation. The compliance with the requirements set forth in paragraphs 6. and 7.. above shall be verified as follows: 9.28.1.1. The minimum requirements for conformity of production control procedures set forth in Annex 5 17 to this Regulation shall be complied with. 9.38.1.2. The minimum requirements for sampling by an inspector set forth in Annex 7 18 to this Regulation shall be complied with. 9.48.2. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting under this Regulation. The compliance with the requirements set forth in paragraphs 6. and 7.. above shall be verified as follows: 9.29.1.1. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.39.1.2. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.49.2. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.59.3. Headlamps with apparent defects are disregarded. 9.4. The measuring points 8 to 15 from paragraph 6.2.5.3. of this Regulation are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 4 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 5 to this Regulation shall be complied with. 9.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.110.1. Headlamps Direction indicators approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.210.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 6 to this Regulation shall be complied with. 9.410.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 of the Agreement (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.110.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 79. above. 9.210.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 4 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 5 to this Regulation shall be complied with. 9.410.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity Conformity of production Production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. 6 and 78 above. 9.2. The minimum requirements for conformity Conformity of production Production control procedures set forth in Annex 5 6 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 of the Agreement (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.110.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 79. above. 9.210.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 4 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 5 to this Regulation shall be complied with. 9.410.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.18.1. Headlamps Retro-reflectors approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. above. 9.28.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 17 to this Regulation shall be complied with. 9.38.3. The minimum requirements for sampling by an inspector set forth in Annex 7 18 to this Regulation shall be complied with. 9.48.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps A system approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. 9.2. The minimum requirements for conformity of production control procedures set forth fourth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps Systems or part(s) thereof with apparent defects are disregarded. 9.6. The reference xxxx is disregarded.

Conformity of production. The conformity Conformity of production Production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-ECE/324- E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.1. Headlamps Lamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. 6 and 78 above. 9.2. The minimum requirements for conformity Conformity of production Production control procedures set forth in Annex 5 annex 6 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded." MINIMUM REQUIREMENTS FOR CONFORMITY OF PRODUCTION CONTROL PROCEDURES

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.110.1. Headlamps Direction indicators approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.210.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 6 to this Regulation shall be complied with. 9.410.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps A system approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. above. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps Systems or part(s) thereof with apparent defects are disregarded. 9.6. The reference xxxx is disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps a system approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. 9.2. The the minimum requirements for conformity of production control procedures set forth fourth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps Systems or part(s) thereof with apparent defects are disregarded. 9.6. The reference mark is disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) ), with the following requirements: 9.110.1. Headlamps Direction indicators approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 78. above. 9.210.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 6 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.410.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. 9.2. The minimum requirements for conformity of production control procedures set forth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps with apparent defects are disregarded. 9.6. The measuring points 8 to 15 from paragraph 6.2.5.3. of this Regulation are disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.1. Headlamps a system approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. and 7. 9.2. The the minimum requirements for conformity of production control procedures set forth fourth in Annex 5 to this Regulation shall be complied with. 9.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.5. Headlamps Systems or part(s) thereof with apparent defects are disregarded. 9.6. The reference xxxx is disregarded.

Conformity of production. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 9.110.1. Headlamps approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraphs 6. 6 and 7. 9.210.2. The the minimum requirements for conformity of production control procedures set forth fourth in Annex 5 to this Regulation shall be complied with. 9.310.3. The minimum requirements for sampling by an inspector set forth in Annex 7 to this Regulation shall be complied with. 9.410.4. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. 9.510.5. Headlamps with apparent defects are disregarded. 10.6. The reference xxxx is disregarded.