Control Levers and Cables Sample Clauses

Control Levers and Cables. Throttle lever and cable: Make sure the cable is not frayed or kinked in any way also check to be sure that the cable housing ends are se- curely seated. An adjustment is available at the carburetor and you can increase or take up slack by screwing or unscrewing the adjust- ment barrel. Brake lever and cable: Make sure the cable is not frayed or kinked in any way also check to be sure that the cable housing ends are se- curely seated. An adjustment is available at the brakes and you can increase or take up slack by screwing or unscrewing the adjustment bar
Sample 1
AutoNDA by SimpleDocs
Control Levers and Cables. Throttle lever and cable: Make sure the cable is not frayed or kinked in any way. Also check to be sure that the cable housing ends are securely seated. An adjustment is available at the carburetor and you can increase or take up slack by screwing or unscrewing the adjustment barrel. Check the frame, fork, and “t” handle, particularly in areas around all tube joints for any deep scratches, cracks, or discoloration. These are signs of stress-caused “fatigue” or overloading and indicate that a part is at the end of its useful life and needs to be replaced. Check to make sure that all parts and accessories are still secure, tighten any which are not. Check drive components for wear adjust or replace if necessary. If your scooter is fitted with a chain drive, clean and oil chain and check chain tension.
Sample 1

Related to Control Levers and Cables

  • Infrastructure Vulnerability Scanning Supplier will scan its internal environments (e.g., servers, network devices, etc.) related to Deliverables monthly and external environments related to Deliverables weekly. Supplier will have a defined process to address any findings but will ensure that any high-risk vulnerabilities are addressed within 30 days.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Benchmarks for Measuring Accessibility For the purposes of this Agreement, the accessibility of online content and functionality will be measured according to the W3C’s Web Content Accessibility Guidelines (WCAG) 2.0 Level AA and the Web Accessibility Initiative Accessible Rich Internet Applications Suite (WAI-ARIA) 1.0 for web content, which are incorporated by reference. Adherence to these accessible technology standards is one way to ensure compliance with the College’s underlying legal obligations to ensure that people with disabilities are able to acquire the same information, engage in the same interactions, and enjoy the same benefits and services within the same timeframe as their nondisabled peers, with substantially equivalent ease of use; that they are not excluded from participation in, denied the benefits of, or otherwise subjected to discrimination in any College programs, services, and activities delivered online, as required by Section 504 and the ADA and their implementing regulations; and that they receive effective communication of the College’s programs, services, and activities delivered online.

  • Access Controls a. Authorized Access - DST shall have controls that are designed to maintain the logical separation such that access to systems hosting Fund Data and/or being used to provide services to Fund will uniquely identify each individual requiring access, grant access only to authorized personnel based on the principle of least privileges, and prevent unauthorized access to Fund Data.

  • PERFORMANCE MANAGEMENT SYSTEM 5.1 The Employee agrees to participate in the performance management system that the Employer adopts or introduces for the Employer, management and municipal staff of the Employer.

  • Earned Value Management System ‌ An earned value management system (EVMS) means a project management tool that effectively integrates the project scope of work with cost, schedule and performance elements for optimum project planning and control. The qualities and operating characteristics of EVMS are described in American National Standards Institute /Electronics Industries Alliance (ANSI/EIA) Standard-748. An EVMS is not mandatory; however, Contractors are encouraged to have an EVMS ANSI/EIA Standard-748 during the entire term of OASIS. The Contractor shall notify the OASIS CO, in writing, if there are any changes in the status of their EVMS and provide the reasons for the change and copies of audits by the Defense Contract Management Agency (DCMA) or other cognizant Government administration office, as applicable. If only part of a Contractor’s organization is EVMS ANSI/EIA Standard-748 certified, the Contractor shall make the distinction between which business units or sites and geographic locations have been certified.

  • Commodity Compliance and Compatibility It is the Contractor’s responsibility to ensure that the Commodities supplied are compliant with the Contract requirements, specifications, terms, and conditions. Additionally, the Contractor shall ensure that all Commodities ordered by the Customer are fully compatible with each other and with any associated pre-existing Commodity possessed by the Customer and disclosed to the Contractor by the Customer. The Contractor’s acceptance of the Customer’s order shall indicate that the Contractor agrees to deliver a Commodity that is fully compliant and compatible with the Customer’s order requirements, specifications, terms, and conditions. In the event any ordered Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components are found by the Customer to be missing, incorrect, defective, damaged, non- compatible, or non-compliant, the Contractor shall, at the Customer’s discretion, be required to complete one of the following: • Install or repair the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s), and their respective features, equipment, and components; • Replace the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components; • Refund the purchase price of the Base Equipment, OEM and Non-OEM Option(s), Part(s), Accessory(ies), and Implement(s); and their respective features, equipment, and components to the Customer. Any changes necessary after the delivery of the Customer’s order that are required to bring a Commodity into compliance or compatibility due to an incorrect order fulfillment by the Contractor shall be accomplished at the Contractor’s expense.

  • Switching System Hierarchy and Trunking Requirements For purposes of routing ECI traffic to Verizon, the subtending arrangements between Verizon Tandem Switches and Verizon End Office Switches shall be the same as the Tandem/End Office subtending arrangements Verizon maintains for the routing of its own or other carriers’ traffic (i.e., traffic will be routed to the appropriate Verizon Tandem subtended by the terminating End Office serving the Verizon Customer). For purposes of routing Verizon traffic to ECI, the subtending arrangements between ECI Tandem Switches and ECI End Office Switches shall be the same as the Tandem/End Office subtending arrangements that ECI maintains for the routing of its own or other carriers’ traffic.

  • Trunk Group Architecture and Traffic Routing The Parties shall jointly engineer and configure Local/IntraLATA Trunks over the physical Interconnection arrangements as follows:

  • Physical Access Control Unauthorized persons are prevented from gaining physical access to premises, buildings or rooms where data processing systems that process and/or use Personal Data are located.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!