Correction Factors for Volume Measurement Sample Clauses

Correction Factors for Volume Measurement. The computations of the volumes of Gas measured shall be made as follows: (a) The hourly orifice coefficient for each meter shall be calculated at the base pressure of fourteen and sixty-five hundredths (14.65) psia and the base temperature of sixty (60) degrees Fahrenheit. All Gas volume measurements shall be based on a local atmospheric pressure assumed to be thirteen and seven-tenths (13.7) psia. (b) The flowing temperature of the Gas shall be continuously measured. In the case of electronic metering, such temperature measurement shall be used as continuous input to the flow computer for calculation of Gas volume, mass and/or energy content in accordance with the applicable AGA or API 21.1 standards including, but not limited to, AGA Report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (c) Measurements of inside diameters of pipe runs and orifices shall be obtained by means of a micrometer to the nearest one-thousandth of an inch, and such measurements shall be used in computations of coefficients. (d) In determining the volume of Gas, when electronic transducers and flow computers are used, the Gas shall have its volume, mass and/or energy content continuously integrated in accordance with the applicable AGA standards including, but not limited to, AGA report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (e) In calculating the volume of Gas, deviation from Xxxxx’x Law at the pressure, specific gravity, and temperature for each measurement shall be determined by use of AGA Report No. 8
Sample 1Sample 2See All (4)
AutoNDA by SimpleDocs
Correction Factors for Volume Measurement. The computations of the volumes of Gas measured shall be made as follows: (a) The hourly orifice coefficient for each meter shall be calculated at the base pressure of fourteen and sixty-five hundredths (14.65) psia and the base temperature of sixty (60) degrees Fahrenheit. All Gas volume measurements shall be based on a local atmospheric pressure assumed to be thirteen and seven-tenths (13.7) psia. Gas Processing Agreement dated September 1, 2021 Between Altus Midstream Processing LP (Processor) and Apache Corporation (Producer) (b) The flowing temperature of the Gas shall be continuously measured. In the case of electronic metering, such temperature measurement shall be used as continuous input to the flow computer for calculation of Gas volume, mass and/or energy content in accordance with the applicable AGA or API 21.1 standards including, but not limited to, AGA Report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (c) Measurements of inside diameters of pipe runs and orifices shall be obtained by means of a micrometer to the nearest one-thousandth of an inch, and such measurements shall be used in computations of coefficients. (d) In determining the volume of Gas, when electronic transducers and flow computers are used, the Gas shall have its volume, mass and/or energy content continuously integrated in accordance with the applicable AGA standards including, but not limited to, AGA report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (e) In calculating the volume of Gas, deviation from Xxxxx’x Law at the pressure, specific gravity, and temperature for each measurement shall be determined by use of AGA Report No. 8
Sample 1
Correction Factors for Volume Measurement. The computations of the volumes of Gas measured shall be made as follows: (a) The hourly orifice coefficient for each meter shall be calculated at the base pressure of fourteen and sixty-five hundredths (14.65) psia and the base temperature of sixty (60) degrees Fahrenheit. All Gas volume measurements shall be based on a local atmospheric pressure assumed to be thirteen and seven-tenths (13.7) psia. (b) The flowing temperature of the Gas shall be continuously measured. In the case of electronic metering, such temperature measurement shall be used as continuous input to the flow computer for calculation of Gas volume, mass and/or energy content in accordance with the applicable AGA or API 21.1 standards including, but not limited to, AGA Report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (c) Measurements of inside diameters of pipe runs and orifices shall be obtained by means of a micrometer to the nearest one-thousandth of an inch, and such measurements shall be used in computations of coefficients. Gas Processing Agreement dated July 1, 2018 Between Alpine High Processing LP (Processor) and Apache Corporation (Producer) (d) In determining the volume of Gas, when electronic transducers and flow computers are used, the Gas shall have its volume, mass and/or energy content continuously integrated in accordance with the applicable AGA standards including, but not limited to, AGA report Nos. 3, 5, 6, 7 and 8 and any subsequent modification and amendments thereof generally accepted within the Gas industry. (e) In calculating the volume of Gas, deviation from Xxxxx’x Law at the pressure, specific gravity, and temperature for each measurement shall be determined by use of AGA Report No. 8, Compressibility Factors for Natural Gas and Other Related Hydrocarbon Gases, published by the AGA in conjunction with Gas Measurement Committee Report No. 3 and amendments thereto generally accepted within the Gas industry. (f) Whenever the conditions of pressure and temperature differ from the standards described herein, conversion of the volume from these conditions to the standard conditions shall be made in accordance with the Ideal Gas Laws, corrected for deviation by the methods set forth in the AGA Gas Measurement Committee Report No. 3, as said report may be amended from time to time.
Sample 1

Related to Correction Factors for Volume Measurement

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Temperature Measurement Temperature will be measured by the nearest automatic Melbourne Bureau of Meteorology Monitoring Station for example (but not limited to): Melbourne, Moorabbin, Dunns Hill, Melbourne Airport, Frankston, and Point Xxxxxx. At the commencement of each project, the onsite management and employee representatives shall agree which is to be the applicable automatic weather monitoring station.

  • Performance Measurement The Uniform Guidance requires completion of OMB-approved standard information collection forms (the PPR). The form focuses on outcomes, as related to the Federal Award Performance Goals that awarding Federal agencies are required to detail in the Awards.

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

  • Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.

  • Adjustment of Minimum Quarterly Distribution and Target Distribution Levels (a) The Minimum Quarterly Distribution, First Target Distribution, Second Target Distribution, Third Target Distribution, Common Unit Arrearages and Cumulative Common Unit Arrearages shall be proportionately adjusted in the event of any distribution, combination or subdivision (whether effected by a distribution payable in Units or otherwise) of Units or other Partnership Securities in accordance with Section 5.10. In the event of a distribution of Available Cash that is deemed to be from Capital Surplus, the then applicable Minimum Quarterly Distribution, First Target Distribution, Second Target Distribution and Third Target Distribution, shall be adjusted proportionately downward to equal the product obtained by multiplying the otherwise applicable Minimum Quarterly Distribution, First Target Distribution, Second Target Distribution and Third Target Distribution, as the case may be, by a fraction of which the numerator is the Unrecovered Capital of the Common Units immediately after giving effect to such distribution and of which the denominator is the Unrecovered Capital of the Common Units immediately prior to giving effect to such distribution. (b) The Minimum Quarterly Distribution, First Target Distribution, Second Target Distribution and Third Target Distribution, shall also be subject to adjustment pursuant to Section 6.9.

  • Power Factor Design Criteria (Reactive Power A wind generating plant shall maintain a power factor within the range of 0.95 leading to 0.95 lagging, measured at the Point of Interconnection as defined in this LGIA, if the ISO’s System Reliability Impact Study shows that such a requirement is necessary to ensure safety or reliability. The power factor range standards can be met using, for example without limitation, power electronics designed to supply this level of reactive capability (taking into account any limitations due to voltage level, real power output, etc.) or fixed and switched capacitors if agreed to by the Connecting Transmission Owner for the Transmission District to which the wind generating plant will be interconnected, or a combination of the two. The Developer shall not disable power factor equipment while the wind plant is in operation. Wind plants shall also be able to provide sufficient dynamic voltage support in lieu of the power system stabilizer and automatic voltage regulation at the generator excitation system if the System Reliability Impact Study shows this to be required for system safety or reliability.

  • Measuring EPP parameters Every 5 minutes, EPP probes will select one “IP address” of the EPP servers of the TLD being monitored and make an “EPP test”; every time they should alternate between the 3 different types of commands and between the commands inside each category. If an “EPP test” result is undefined/unanswered, the EPP service will be considered as unavailable from that probe until it is time to make a new test.

  • Performance Adjustment One-twelfth of the annual Performance Adjustment Rate will be applied to the average of the net assets of the Portfolio (computed in the manner set forth in the Fund's Declaration of Trust or other organizational document) determined as of the close of business on each business day throughout the month and the performance period.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!