Common Areas - Rules and Regulations Lessor or such other person(s) as Lessor may appoint shall have the exclusive control and management of the Common Areas and shall have the right, from time to time, to establish, modify, amend and enforce reasonable rules and regulations (“Rules and Regulations”) for the management, safety, care, and cleanliness of the grounds, the parking and unloading of vehicles and the preservation of good order, as well as for the convenience of other occupants or tenants of the Building and the Project and their invitees. Lessee agrees to abide by and conform to all such Rules and Regulations, and to cause its employees, suppliers, shippers, customers, contractors and invitees to so abide and conform. Lessor shall not be responsible to Lessee for the non-compliance with said Rules and Regulations by other tenants of the Project.
Compliance with Governmental Rules and Regulations Except as otherwise provided in the Agreement and except for the accuracy of information furnished to the Fund by Price Services, each Fund assumes full responsibility for the preparation, contents and distribution of its prospectuses and compliance with all applicable requirements of the ’40 Act, the ‘34 Act, the ‘33 Act, and any other laws, rules and regulations of governmental authorities having jurisdiction over the Fund. Price Services shall be responsible for complying with all laws, rules and regulations of governmental authorities having jurisdiction over transfer agents and their activities and cooperating with respect to examinations and requests from such governmental authorities.
Compliance with Rules and Regulations PFPC undertakes to comply with all applicable requirements of the Securities Laws and any laws, rules and regulations of governmental authorities having jurisdiction with respect to the duties to be performed by PFPC hereunder. Except as specifically set forth herein, PFPC assumes no responsibility for such compliance by the Fund or any other entity.
Geographic Area and Sector Specific Allowances, Conditions and Exceptions The following allowances and conditions shall apply where relevant. Where the Employer does work which falls under the following headings, the Employer agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.
Compliance with OFAC Rules and Regulations None of the Credit Parties or their Subsidiaries or their respective Affiliates (a) is a Sanctioned Person, (b) has more than 15% of its assets in Sanctioned Countries, or (c) derives more than 15% of its operating income from investments in, or transactions with Sanctioned Persons or Sanctioned Countries. No part of the proceeds of any Extension of Credit hereunder will be used directly or indirectly to fund any operations in, finance any investments or activities in or make any payments to, a Sanctioned Person or a Sanctioned Country.
Compliance with Accessibility Standards All parties to this Agreement shall ensure that the plans for and the construction of all projects subject to this Agreement are in compliance with standards issued or approved by the Texas Department of Licensing and Regulation (TDLR) as meeting or consistent with minimum accessibility requirements of the Americans with Disabilities Act (P.L. 101-336) (ADA).
Compliance with Laws, Rules and Regulations a. Assurances. The Contractor agrees that all activity pursuant to this Contract will be in accordance with all applicable current federal, state and local laws, rules, and regulations, including but not limited to the Public Records Act (chapter 42.56 RCW), the Freedom of Information Act (5 U.S.C. 522) and the Records Retention Act (chapter 40.14 RCW).
COMPLIANCE WITH GOVERNMENTAL RULES AND REGULATIONS; RECORDS The Trust assumes full responsibility for its compliance with all securities, tax, commodities and other laws, rules and regulations applicable to it.
GENERAL WORKING CONDITIONS Section 18-1. Employment begins and ends at each project site. Section 18-2. The selection of craft foremen and/or general foremen and the number of foremen required shall be entirely the responsibility of the Employer, it being understood that in the selection of such foremen and/or general foremen the Employer will give primary consideration to the qualified individuals available in the local area. After giving such consideration, the Employer may select such individuals from other areas. All foremen shall take orders from the designated Employer representatives. Craft foremen shall be designated working foremen at the request of the Employer. Section 18-3. There shall be no limit on production by employees nor restrictions on the full use of tools or equipment. Employees using tools shall perform any of the work of the trade and shall work under the direction of the craft foremen. There shall be no restrictions on efficient use of manpower other than as may be required by safety regulations. Section 18-4. Employees shall be at their place of work at the starting time and shall remain at their place of work performing their assigned functions under the supervision of the Employer until quitting time. The parties reaffirm their policy of a fair day’s work for a fair day’s wage. Section 18-5. All equipment assigned to a project shall be under the control of the Employer. The Employer shall have the right to determine how many pieces of equipment an individual employee shall operate. In an emergency, foremen shall operate any equipment assigned by the Employer, and there shall be no restriction on foremen in the use of the tools of his or her craft in such emergency. The foremen shall be from the craft normally operating the equipment. In accordance with currently recognized craft jurisdiction, the Employer shall determine the assignment of employees to start, stop, and maintain small portable construction equipment. Such work may be assigned to craft employees within a reasonable distance of their primary duties or an employee may be assigned full time to start, stop and maintain the Employer’s small, portable equipment on the job site. There shall be no over xxxxxxx of this type of equipment. The number of employees assigned to rigging and scaffolding operations shall be at the sole discretion of the Employer. The ratio of journeyperson to welders shall be determined solely by the Employer. Section 18-6. The Employer may utilize the most efficient methods or techniques of construction, tools or other labor saving devices to accomplish the work. Practices not a part of the terms and conditions of this Agreement, stand by crews and feather bedding practices will not be recognized. Section 18-7. It is recognized that specialized or unusual equipment may be installed and/ or serviced by individuals who have special training, skill, or qualifications and are not covered by this Agreement. Testing, inspection, or service performed on plant equipment under warranty may be performed by the vendor’s personnel. Section 18-8. Neither the Union nor its local unions shall coerce or in any way interfere with the Owner’s personnel, operation or facilities at the plant site. The Owner’s right to contract directly with other companies for work at the plant site shall not be limited, and the Union shall cooperate and not interfere with the Employer’s operations. Section 18-9. It is agreed that overtime is undesirable and not in the best interest of the industry or the employees; therefore, except in unusual circumstances, overtime will not be worked. Where unusual circumstances do exist, however, the Employer will have the right to assign specific employees and/or crews to perform such overtime work as is necessary to accomplish the job. Section 18-10. There will be no rest periods, organized coffee breaks or other non-working time established during working hours. Section 18-11. Individual seniority shall not be recognized or applied to employees working on projects under this Agreement. Section 18-12. The Employer shall establish such reasonable project rules as the Employer deems appropriate. These rules will be reviewed at the pre-job conference and posted at the project site by the Employer, and may be amended thereafter as necessary.
Compliance with Americans with Disabilities Act Contractor shall provide the Services in a manner that complies with the Americans with Disabilities Act (ADA), including but not limited to Title II’s program access requirements, and all other applicable federal, state and local disability rights legislation.
