DETAILED TECHNICAL Sample Clauses

DETAILED TECHNICAL. SPECIFICATIONS OF THE SYSTEM 2.4.1 Frequency range for the service i. Base Station to end user terminal *** ii. End user terminal to Base Station *** 2.4.2 Transmission equipment to be installed at Base Station i. Emission designation : *** ii. Output power at the output of paging transmitter : *** iii. Frequency error : *** of the designated frequency iv. Occupied bandwidth : ***
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
DETAILED TECHNICAL. SPECIFICATIONS (DTS)
Sample 1
DETAILED TECHNICAL. REQUIREMENTS The autoclave shall generally conform to the requirements of SABS 982- 1973, as amended and shall have the following additional features: The autoclave shall be fully automatic and be suitable for the sterilization of packs and fluids, having a vertically sliding door. The autoclave shall be of the single door recessed type with a rectangular chamber having internal dimensions of approximately 660 mm x 660 mm x 910 mm and the chamber walls shall be of a thickness not less than 9,0 mm and a chamber volume of approximately 400 litres 0,4 m3. The chamber shall be jacketed along its full length and the rear end. The jacketed surface shall be not less than 80 % of the Autoclave chamber outside surface, taken on individually sections as well as in total. The jackets shall be made of the same material as the chamber and it's manufacture / construction shall be in accordance with RSA/CIF 89-89 A90. Normal sterilizing temperature shall be 134 °C for packs and instruments. It must be possible to set temperature to 121 °C for the sterilization of fluids and baby bottles. The design of the steam piping and positioning of valves shall be such that steam pass through the jacket before entering the chamber. The jacket shall be adequately rapidly drained of condensate at a rate which will ensure that only dry saturated steam can enter the chamber. The entry of steam into the chamber shall facilitate the separation of any remaining moisture in this steam to reduce the possibility of water impinging onto the surface of the articles to be sterilized. The autoclave will operate at the altitude above sea level as specified in the request and the source of vacuum must be able to draw a vacuum of 70kPa in the steriliser chamber within 3 minutes. Total cycle time for packs shall be approximately 20 minutes but may not exceed 25 minutes.
Sample 1

Related to DETAILED TECHNICAL

  • Technical Foreign Affairs Training for professional skills of a specialized nature in the methods and techniques of such fields as foreign languages, foreign culture, intelligence (foreign affairs/intelligence), diplomacy, or strategic studies. Technical

  • Technical Information The Employer agrees to provide to the Union such information that is available relating to employees in the bargaining unit, as may be required by the Union for collective bargaining purposes.

  • Licensed Software Computer program(s) provided by Contractor in connection with the Deliverables, subject to Section 14 of this Contract.

  • Technical Data For the purpose of this Agreement, "TECHNICAL DATA" shall mean all information of the Company in written, graphic or tangible form relating to any and all products which are developed, formulated and/or manufactured by the Company, as such information exists as of the Effective Date or is developed by the Company during the term hereof.

  • Personnel Equipment and Material Engineer shall furnish and maintain, at its own expense, quarters for the performance of all Engineering Services, and adequate and sufficient personnel and equipment to perform the Engineering Services as required. All employees of Engineer shall have such knowledge and experience as will enable them to perform the duties assigned to them. Any employee of Engineer who, in the reasonable opinion of County, is incompetent or whose conduct becomes detrimental to the Engineering Services shall immediately be removed from association with the Project when so instructed by County. Engineer certifies that it presently has adequate qualified personnel in its employment for performance of the Engineering Services required under this Contract, or will obtain such personnel from sources other than County. Engineer may not change the Project Manager without prior written consent of County.

  • Time and Materials If this contract is designated as a Time and Materials contract, invoicing and payment shall be as follows: (a) Consultant shall submit invoices, not more often than once a month during the term of this agreement, based on the cost for work performed in accordance with the Rate Schedule in the Scope of Work and authorized reimbursable expenses incurred prior to the invoice date. Invoices shall contain the following information: (i) Serial identifications of bills, i.e., Xxxx No. 1; (ii) The beginning and ending dates of the billing period; (iii) A summary containing the total contract amount, the amount of prior xxxxxxxx, the total due this period, percentage of work completed, the remaining balance available for all remaining billing periods, and a brief description of work completed during the billing period. (b) City shall make monthly payments, based on such invoices, for satisfactory progress in completion of the Scope of Work, and for authorized reimbursable expenses incurred.

  • Training Materials Training Materials will be provided for each student. Training Materials may be used only for either (i) the individual student’s reference during Boeing provided training and for review thereafter or (ii) Customer’s provision of training to individuals directly employed by the Customer.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!