Felling in Clearings Sample Clauses

Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and areas of regeneration cutting.
AutoNDA by SimpleDocs
Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not extend outside clearcutting units, construction clearings, and areas of regeneration cutting. Xxxxx Heights. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in Appendix E except that occasional stumps of greater heights are acceptable when determine(s) that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, shall re-cut high stumps so they will not exceed heights specified in F-14 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in Appendix F were selected with the objective of maximum reasonable utilization of the timber, unless the Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural reasons. Bucking Lengths. Trees shall be bucked in various lengths to obtain the greatest utilization of material meeting utilization standards.

Related to Felling in Clearings

  • Construction Clearing All timber is designated for cutting that is within the clearing limits of roads constructed hereunder or is in other authorized clearings. All dead or unstable live trees are designated for cutting that are sufficiently tall to reach Purchaser’s landings or the roadbed of Specified and Temporary Roads when Marked in advance of felling of timber in the immediate vicinity. Pieces meeting Utilization Standards from such dead or unstable live trees shall be removed, unless there is agreement that to do so could damage the road. Such designation may be revised as part of agreed changes in road location under B5.2.

  • Clearing Purchaser shall fall all vegetative material larger than 2 inches DBH or over 5 feet high between the marked right‐of‐way boundaries and within waste and debris areas, or if not marked in the field, between the clearing limits specified on the TYPICAL SECTION SHEET. Clearing must be completed before starting excavation and embankment.

  • Alternative Clearing System References in this Agreement to Euroclear and/or Clearstream, Luxembourg shall, wherever the context so permits, be deemed to include reference to any additional or alternative clearing system approved by the Issuer, the Guarantor, the Registrar and the Issuing and Principal Paying Agent.

  • Trademark Clearinghouse 4.1 Notwithstanding the requirements of Section 2.8 of the Agreement, Section 1 of Specification 7 to the Agreement and Section 2 of the Trademark Clearinghouse Rights Protection Mechanism Requirements (the “TMCH Requirements”), Registry Operator is not required to provide a Sunrise Period (as defined in the TMCH Requirements) or, except as set forth herein, otherwise comply with the obligations set forth in Section 2 of the TMCH Requirements (collectively, the “Sunrise Requirements”) so long as the TLD continues to be qualified as a .Brand TLD by ICANN.

  • CURVE WIDENING The minimum widening placed on the inside of curves is:  6 feet for curves of 50 to 79 feet radius.  4 feet for curves of 80 to 100 feet radius.

  • Clearing Systems In delivering any Global Note or Global Certificate in accordance with Clause 3.4.1, the Fiscal Agent shall give instructions to the relevant clearing system to hold the Notes represented by it to the order of the Fiscal Agent pending transfer to the securities account(s) referred to in Clause 3.4.1. Upon payment for any such Notes being made to the Fiscal Agent, it shall transfer such payment to the account of the Issuer notified to it by the Issuer. For so long as any such Note continues to be held to the order of the Fiscal Agent, the Fiscal Agent shall hold such Note to the order of the Issuer.

  • designated Trademark Clearinghouse If there is a conflict between the terms and conditions of this Agreement and the Trademark Clearinghouse Requirements, the terms and conditions of this Agreement shall control.

  • Submitting Loop Makeup Service Inquiries 2.9.2.1 C.M. may obtain LMU information by submitting a mechanized LMU query or a Manual LMUSI. Mechanized LMUs should be submitted through BellSouth's OSS interfaces. After obtaining the Loop information from the mechanized LMU process, if C.M. needs further Loop information in order to determine Loop service capability, C.M. may initiate a separate Manual Service Inquiry for a separate nonrecurring charge as set forth in Exhibit A of this Attachment.

  • Loop Makeup Response Time - Electronic This report measures the average interval and the percent within the interval from the electronic submission of a Loop Makeup Service Inquiry (LMUSI) to the distribution of Loop Makeup information back to the CLEC. Exclusions Manually submitted inquiries Canceled Requests Business Rules The response interval starts when the CLEC’s Mechanized Loop Makeup Service Inquiry (LMUSI) is submitted electronically through the Operational Support Systems interface, TAG. It ends when BellSouth’s Loop Facility Assignment and Control System (LFACS) responds electronically to the CLEC with the requested Loop Makeup data via the TAG Interface. LSRs submitted via LENs will be reflected in the results for the TAG interface.

  • Inoculations The Employer agrees to pay full expenses for inoculation or immunization shots for the employee and for members of an employee’s household when such becomes necessary as a result of said employee’s exposure to contagious diseases (including AIDS, tuberculosis and hepatitis) where said officer has been exposed to said disease in the line of duty.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!