Felling and Bucking Sample Clauses

Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Sample 1Sample 2Sample 3See All (158)
AutoNDA by SimpleDocs
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A.2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in
Sample 1Sample 2Sample 3See All (33)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Stand- ards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchanta- bility factor, whichever is stated in A2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges.‌‌
Sample 1Sample 2Sample 3See All (19)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in AT2. Con- tractor may buck out cull material when necessary to pro- duce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net Measure in percentage of gross Measure, or based on the merchantability factor, whichever is stated in AT2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges. BT6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend
Sample 1Sample 2Sample 3See All (6)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to re- sidual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth on Page 1. Purchaser may buck out cull material when necessary to produce pieces meet- ing Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated on Page 1. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not extend outside Clearcutting Units, clearings, and areas of regeneration cutting.
Sample 1Sample 2Sample 3
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to re- sidual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth on Page 1. Purchaser may buck out cull material when necessary to produce pieces meet- ing Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net Measure in percentage of gross Measure, or based on the merchantability factor, whichever is stated on Page 1. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. BT6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings permit, trees shall be felled so that their tops do not extend outside Clearcutting Units, clearings, and areas of regeneration cutting. BT6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum height set forth on Page 1, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed Purchaser shall re-cut high stumps so they will not exceed height specified on Page 1 and shall dispose of severed portions in the same manner as other logging debris or as otherwise agreed. The xxxxx heights shown on Page 1 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural reasons. BT6.413 Limbing. When Forest Service determines it is necessary to minimize damage to the residual stand during skidding, Purchaser shall cut exposed limbs from products prior to skidding. Purchaser may be leave uncut those limbs that cannot be cut with reasonable safety. BT6.42 Skidding and Yarding. Methods of skidding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. BT6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees designated for
Sample 1Sample 2
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Felling shall be done by saws or shears. Trees may not be left hanging on other trees. All hung trees or spring poles must be fell or released, dropped or pulled down to the ground the day they occur. Xxxxx Heights: Stumps shall not exceed, on the side adjacent to highest ground, the maximum height of 12 inches, unless agreed otherwise in writing by Seller or their Representative. Limbing: When necessary to minimize damage to residual stand during skidding, exposed limbs shall be cut from products prior to skidding. Such limbs may be left uncut which cannot be cut with reasonable safety. Skidding: In so far as ground conditions permit products shall not be skidded against unmarked trees or groups of pole trees or groups of reproduction, and skidders or tractors shall be equipped with winch to facilitate skidding. Landings and Skid Trails: Location of all landings, skid roads, skid trails shall be agreed upon prior to construction or use in writing. Landings and major skid trails will be flagged in prior to construction and use.
Sample 1
AutoNDA by SimpleDocs
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting.
Sample 1

Related to Felling and Bucking

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction. (b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.

  • Marketing and Sales Provide a detailed plan beginning from award date of the Master Agreement describing the strategy to immediately implement the Master Agreement as supplier’s primary go to market strategy for Public Agencies to supplier’s teams, to include, but not limited to:

  • Training and Promotion a. The contractor will assist in locating, qualifying, and increasing the skills of minorities and women who are applicants for employment or current employees. Such efforts should be aimed at developing full journey level status employees in the type of trade or job classification involved. b. Consistent with the contractor's work force requirements and as permissible under Federal and State regulations, the contractor shall make full use of training programs, i.e., apprenticeship, and on-the-job training programs for the geographical area of contract performance. In the event a special provision for training is provided under this contract, this subparagraph will be superseded as indicated in the special provision. The contracting agency may reserve training positions for persons who receive welfare assistance in accordance with 23 U.S.C. 140(a). c. The contractor will advise employees and applicants for employment of available training programs and entrance requirements for each. d. The contractor will periodically review the training and promotion potential of employees who are minorities and women and will encourage eligible employees to apply for such training and promotion.

  • Training and Professional Development 11.1 The Employer will develop and maintain an employee training and development plan and provide such plan to the Union upon request. Staff training is intended to provide an opportunity for classified staff employees for training sponsored by the University Training and Development and the UW Medical Centers Organizational Development and Training. Education/Professional Leave is intended to facilitate employee access to continuing education opportunities. Training and educational/professional leave may be used for the purpose of improving job performance, maintaining and increasing proficiency, preparing staff for greater responsibility, or increasing promotional opportunities within the framework of staff positions available at the University. 11.2 Any release time for training for employees accepted for such classes shall be in accordance with the Executive Order (currently No. 52) governing this matter. In the event that two or more employees request the same training period and supervision must limit the number of persons who may participate at one time due to work requirements, the selection will be made on a mutually agreeable basis within the department. 11.3 The training program is a proper subject for discussion by either departmental or University-wide Joint Union/Management Committees. 11.4 If the Employer requires an employee to receive training, reimbursement will be provided in accordance with the University travel rules. Employee attendance at Employer required training, either during or outside working hours, will be considered time worked and compensated in accordance with the provisions of this Agreement. 11.5 Employee attendance at training not required by the Employer and not covered by Executive Order 52, either on approved leave from or outside of working hours, will be voluntary and not considered time worked.

  • Training and Development 3.1 Authorities will develop local 'Workforce Development Plans (see Part 4.8),' closely linked to their service delivery plans, which will provide the focus for the establishment of training and development priorities. Training and development should be designed to meet the corporate and service needs of authorities both current and in the future, taking into account the individual needs of employees. Local schemes on training and development should enable authorities to attain their strategic objectives through development of their employees. Training and development provisions should be shaped to local requirements and take account of the full range of learning methods. Such an approach should enable access to learning for all employees. The needs of part time employees and shift workers need particular consideration. 3.2 Employees attending or undertaking required training are entitled to payment of normal earnings; all prescribed fees and other relevant expenses arising. Employees are also entitled to paid leave for the purpose of sitting for required examinations. When attending training courses outside contracted daily hours, part-time employees should be paid on the same basis as full- time employees. (Assistance for other forms of learning, for example that directed at individual development, will be locally determined). Some training can be very expensive and authorities may require repayment of all or part of the costs incurred should an employee leave the authority before a reasonable time period has expired. The authority's policy in this regard should be made explicit. 3.3 Objectives for training and development programmes should include the following: • To enable Councils to attain their strategic objectives via investment in their employees. • To promote equity of access to learning. • To encourage employees to develop their skills and level of responsibility to the maximum of their individual potential. • To widen and modernise the skills profile of employees to maximise their versatility, employability and so, job security. • To enable employees to raise productivity, quality and customer service in pursuit of sustainable improvement 3.4 Authorities should establish local partnership arrangements, to include recognised trade unions, to develop their local workforce development plans. 3.5 The NJC endorses partnership provision such as the "Return to Learn" scheme. Authorities and the recognised trade unions shall encourage and support employees taking on the statutory Union Learning Representative (ULR) role. This will include agreeing facilities and paid release in accordance with statutory provisions. ULRs should be enabled to play a full part in promoting and implementing local training and development programmes.

  • Marketing and Promotion The School will be responsible for marketing and promoting the Sports Facilities in accordance with the agreed aims and targets. A marketing strategy will be prepared and implemented and reviewed on an annual basis.

  • Packing and Marking All material and equipment to be furnished by the Contractor shall be packed, crated or otherwise suitably protected to withstand shipment undamaged to the destination. Each package, crate or part shall be marked plainly with the name of the consignee, shipping destination, the Owner's order number, and such other markings as are required. Complete packing lists, one copy with each package and two (2) copies by mail to the Owner at time of shipment, shall be supplied showing contents and identity of each package.

  • Synchronization, Commissioning and Commercial Operation 4.1.1 The Power Producer shall give at least fifteen (15) days written notice to the SLDC / ALDC / DISCOM as the case may be, of the date on which it intends to synchronize the Power Project to the Grid System. 4.1.2 Subject to Article 4.1.1, the Power Project may be synchronized by the Power Producer to the Grid System when it meets all the connection conditions prescribed in the Grid Code and otherwise meets all other Indian legal requirements for synchronization to the Grid System. 4.1.3 The synchronization equipment and all necessary arrangements / equipment including Remote Terminal Unit (RTU) for scheduling of power generated from the Project and transmission of data to the concerned authority as per applicable regulation shall be installed by the Power Producer at its generation facility of the Power Project at its own cost. The Power Producer shall synchronize its system with the Grid System only after the approval of GETCO / SLDC / ALDC and GEDA. 4.1.4 The Power Producer shall immediately after each synchronization / tripping of generator, inform the sub-station of the Grid System to which the Power Project is electrically connected in accordance with applicable Grid Code. 4.1.5 The Power Producer shall commission the Project within SCOD. 4.1.6 The Power Producer shall be required to obtain Developer and/ or Transfer Permission, Key Plan drawing etc, if required, from GEDA. In cases of conversion of land from Agricultural to Non-Agriculture, the commissioning shall be taken up by GEDA only upon submission of N.A. permission by the Power Producer. 4.1.7 The Power Producer shall be required to follow the Forecasting and Scheduling procedures as per the Regulations issued by Hon’ble GERC from time to time. It is to clarify that in terms of GERC (Forecasting, Scheduling, Deviation Settlement and Related Matters of Solar and Wind Generation Sources) Regulations, 2019 the procedures for Forecasting, Scheduling & Deviation Settlment are applicable to all solar generators having combined installed capacity above 1 MW connected to the State Grid / Substation including those connected via pooling stations.

  • Training and Education SECTION 1 – Law Enforcement Supervisors’ Training

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!