FIXED GRILLES. Steel grilles shall be ½ inch or 13mm square bars spaced at 4 inches x 16 inches, horizontal and vertical, designed on a CHB patter, with 1 ¼ inches x 3/16 inch or standard metric equivalent, flat bars for framing.
FIXED GRILLES Sample Clauses
Related to FIXED GRILLES
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Trunk Group Architecture and Traffic Routing 5.2.1 The Parties shall jointly establish Access Toll Connecting Trunks between CLEC and CBT by which they will jointly provide Tandem-transported Switched Exchange Access Services to Interexchange Carriers to enable such Interexchange Carriers to originate and terminate traffic from and to CLEC's Customers. 5.2.2 Access Toll Connecting Trunks shall be used solely for the transmission and routing of Exchange Access and non-translated Toll Free traffic (e.g., 800/888) to allow CLEC’s Customers to connect to or be connected to the interexchange trunks of any Interexchange Carrier that is connected to the CBT access Tandem. 5.2.3 The Access Toll Connecting Trunks shall be one-way or two-way trunks, as mutually agreed, connecting an End Office Switch that CLEC utilizes to provide Telephone Exchange Service and Switched Exchange Access Service in the given LATA to an access Tandem Switch CBT utilizes to provide Exchange Access in the LATA.
Maintenance Employees The normal hours of work for full-time Maintenance employees are 72 ½ hours over a two (2) week period, not to exceed eight (8) hours per day.
Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.
Registry Interoperability and Continuity Registry Operator shall comply with the Registry Interoperability and Continuity Specifications as set forth in Specification 6 attached hereto (“Specification 6”).
CONTRACTOR NAME CHANGE An amendment is required to change the Contractor's name as listed on this Agreement. Upon receipt of legal documentation of the name change the State will process the amendment. Payment of invoices presented with a new name cannot be paid prior to approval of said amendment.
Mail Order Catalog Warnings In the event that, the Settling Entity prints new catalogs and sells units of the Products via mail order through such catalogs to California consumers or through its customers, the Settling Entity shall provide a warning for each unit of such Product both on the label in accordance with subsection 2.4 above, and in the catalog in a manner that clearly associates the warning with the specific Product being purchased. Any warning provided in a mail order catalog shall be in the same type size or larger than other consumer information conveyed for such Product within the catalog and shall be located on the same display page of the item. The catalog warning may use the Short-Form Warning content described in subsection 2.3(b) if the language provided on the Product label also uses the Short-Form Warning.
Maintenance Plan Maintenance plan for the Project Facility for the next quarter and a report on maintenance carried out during the previous quarter (including any material deviation from expected maintenance activities as set out in the maintenance plan).
Configuration Management The Contractor shall maintain a configuration management program, which shall provide for the administrative and functional systems necessary for configuration identification, control, status accounting and reporting, to ensure configuration identity with the UCEU and associated cables produced by the Contractor. The Contractor shall maintain a Contractor approved Configuration Management Plan that complies with ANSI/EIA-649 2011. Notwithstanding ANSI/EIA-649 2011, the Contractor’s configuration management program shall comply with the VLS Configuration Management Plans, TL130-AD-PLN-010-VLS, and shall comply with the following:
Small and medium-sized enterprises 1. The Parties will promote a favourable environment for the development of the small and medium enterprises (SME) on the basis of strengthening of the relevant private and governmental bodies, as well as the exchange of experiences and good practices with the SME. 2. Cooperation shall include, among other subjects: (a) the designing and development of mechanisms to encourage partnership and productive chain linkage development; (b) development of human resources and management skills to increase the knowledge of the Chinese and Peruvian markets; (c) defining and developing methods and strategies for clusters development; (d) increasing access to information regarding mandatory procedures and any other relevant information for an SME exporter; (e) defining technological transference: programs oriented to transfer technological innovation to SME and to improve their productivity; (f) increasing access to information on technological promotion programs for SME and financial support and encouragement programs for SME; (g) supporting new exporting SME (sponsorship, credits and guarantees, seed capital); and (h) encouraging partnership and information exchange for SME financing institutions (credits, banks, guarantee organizations, seed capital firms). 3. Cooperation shall be developed, among other activities, through: (a) information exchange; (b) conferences, seminars, experts dialogue and training programs with experts; and (c) promoting contacts between economic operators, encouraging opportunities for industrial and technical prospecting.
