Inspection and Testing of Meters Sample Clauses

Inspection and Testing of Meters a) PGVCL and SPG shall jointly inspect and if necessary, recalibrate the metering system on a regular basis but in any event, at least once every year or at a shorter interval at the request of any of the two parties.
Sample 1Sample 2Sample 3See All (11)
AutoNDA by SimpleDocs
Inspection and Testing of Meters. Alabama Power or its Affiliate shall have the right to inspect and test all meters installed by Alabama Power or its Affiliate in order to measure the output of the Facility at such times as Alabama Power deems necessary or appropriate. Upon reasonable written request to Alabama Power, QF may request inspection or testing of any such meters. QF shall be responsible for, and shall reimburse Alabama Power for, all costs and expenses incurred by or on behalf of Alabama Power or its Affiliate in connection with such inspections or tests requested by QF unless such inspection or test reveals that such meters are inaccurate by more than two percent (2%) from the measurement made by the reference meter used in the test, in which event Alabama Power shall bear all costs of such testing. Alabama Power shall give reasonable written notice to QF of the time and place when any such meter is to be inspected or tested, and QF may have a representative present at such test or inspection.
Sample 1Sample 2
Inspection and Testing of Meters. 6.2.1 DISCOM/OPTCL shall inspect and if necessary, recalibrate the metering system on a regular basis but in any event, at least once every six (6) months or at a shorter interval at the request of either party.
Sample 1Sample 2
Inspection and Testing of Meters. Buyer shall inspect and test all meters installed by Buyer in order to measure the output of the Facility at such times as Buyer deems necessary or appropriate. Upon reasonable written request to Buyer, Seller may request inspection or testing of any such meters. Seller shall be responsible for, and shall reimburse Buyer for, all reasonable costs and expenses incurred by or on behalf of Buyer or its Affiliate in connection with such inspections or tests requested by Seller unless such inspection or test reveals that such meters are inaccurate by more than two percent (2.0%) from the measurement made by the standard meter used in the test, in which event Buyer shall bear all costs of such testing. Buyer shall give reasonable written notice to Seller of the time and place when any such meter is to be inspected or tested, and Seller may have a representative present at such test or inspection.‌
Sample 1

Related to Inspection and Testing of Meters

  • Inspection and Testing Each Constructing Entity shall cause inspection and testing of the Interconnection Facilities that it constructs in accordance with the provisions of this section. The Construction Parties acknowledge and agree that inspection and testing of facilities may be undertaken as facilities are completed and need not await completion of all of the facilities that a Constructing Entity is building.

  • Inspections and Testing Each Interconnected Entity shall perform routine inspection and testing of its facilities and equipment in accordance with Good Utility Practice as may be necessary to ensure the continued interconnection of the Customer Facility with the Transmission System in a safe and reliable manner. Each Interconnected Entity shall have the right, upon advance written notice, to request reasonable additional testing of an Interconnected Entity’s facilities for good cause, as may be in accordance with Good Utility Practice.

  • Inspections and Tests 26.1 The Supplier shall at its own expense and at no cost to the Procuring Entity carry out all such tests and/or inspections of the Goods and Related Services as are specified in the SCC.

  • INSPECTION/TESTING All Products sold pursuant to this Agreement will be subject to inspection/testing by or at the direction of H- GAC and/or the ordering Customer, either at the delivery destination or the place of manufacture. In the event a Product fails to meet or exceed all requirements of this Agreement, and unless otherwise agreed in advance, the cost of any inspection and/or testing, will be the responsibility of the Contractor.

  • Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.

  • Equipment Testing and Inspection 2.1.1 The Interconnection Customer shall test and inspect its Small Generating Facility and Interconnection Facilities prior to interconnection. The Interconnection Customer shall notify the NYISO and the Connecting Transmission Owner of such activities no fewer than five Business Days (or as may be agreed to by the Parties) prior to such testing and inspection. Testing and inspection shall occur on a Business Day. The Connecting Transmission Owner may, at its own expense, send qualified personnel to the Small Generating Facility site to inspect the interconnection and observe the testing. The Interconnection Customer shall provide the NYISO and Connecting Transmission Owner a written test report when such testing and inspection is completed. The Small Generating Facility may not commence parallel operations if the NYISO, in consultation with the Connecting Transmission Owner, finds that the Small Generating Facility has not been installed as agreed upon or may not be operated in a safe and reliable manner.

  • INSPECTION AND REJECTION 8.1 Purchaser shall have the right to inspect and test Products at any time prior to shipment, and within a reasonable time after delivery to the Purchaser’s Destination. Products not inspected within a reasonable time after delivery shall be deemed accepted by Purchaser. The payment for Products shall in no way impair the right of Purchaser to reject nonconforming Products, or to avail itself of any other remedies to which it may be entitled.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!