Metering and Measurement. Customer and APG&E accept the quantity, quality, and measurement determined by Utility providing delivery service to Service Location, for purposes of accounting for electricity supplied under this Agreement, in accordance with the terms of the applicable tariff for retail delivery service.
Metering and Measurement. Customer and IHPS accept the quantity, quality, and measurement determined by Utility providing delivery service to Service Location, for purposes of accounting for electricity supplied under this Agreement, in accordance with the terms of the applicable tariff for retail delivery service.
Metering and Measurement. (A) Power and energy shall be metered by the Authority at, or as if at, each Delivery Point.
(B) Not less frequently than once each year, the Authority shall make periodic tests and inspections of meters installed by it. At the request of the Customer, the Authority shall make additional tests or inspections. Readings of metering instruments found to be in error by more than two percent (2%) either fast or slow will be corrected and credits or debits made to the Customer's account accordingly. Such correction shall apply for a period of not more than thirty (30) days prior to the date of test unless a longer period of inaccuracy can be definitely determined. The Customer shall pay all costs resulting from additional tests requested by the Customer if tests show meters to be accurate within two percent (2%). Rate Schedule L-96 Attachment A
Metering and Measurement. (a) The Suppliers shall establish and maintain adequate and reliable metering and measuring facilities necessary to monitor the Suppliers’ compliance with their Power and Energy storage, generation and transmission obligations pursuant to this Agreement. Such metering and measuring facilities, including, without limitation, the choice of technical devices and their final set-up and installation, shall be acceptable to all Suppliers.
(b) The parties agree that CF(L)Co shall bear no responsibility for any additional metering and measuring facilities or upgrades or modifications to existing metering and measuring facilities that the parties determine are required pursuant to or resulting from this Agreement, including the cost of establishing, maintaining, repairing or replacing same, provided that any metering and measuring facilities located on CF(L)Co’s facility shall become the property of CF(L)Co on and from the date of installation, and shall thereafter be maintained, repaired and replaced by CF(L)Co, subject to cost recovery therefor by CF(L)Co from Nalcor.
(c) Each of CF(L)Co and Nalcor shall provide to the other all measurements, data and information from the metering and measuring facilities under its control as required for the implementation or operation of this Agreement.
(d) All metering and measuring facilities required for the implementation or operation of this Agreement shall be tested and calibrated at regular intervals established by the Water Management Committee as may be required in accordance with agreed standards. Each Supplier shall give sufficient prior notice to the other of any test which it intends to conduct and the other Supplier may have representatives present for such testing.
(e) Any metering or measuring facility required for the implementation or operation of this Agreement which breaks down, fails to meet the standards as agreed to or set out by the Water Management Committee or otherwise malfunctions, shall be promptly adjusted, repaired or replaced by a similar facility meeting the agreed standards and having the required accuracy, the cost of which shall be the responsibility of Nalcor pursuant to Section 11.2.
(f) Should any metering or measuring facility required for the implementation or operation of this Agreement break down or fail to have the required accuracy, the Suppliers shall determine, through the Water Management Committee, the amount of Power and Energy supplied during the period of failure or inaccuracy...
Metering and Measurement. 10.01 The unit of measurement of the gas shall be one dekatherm of gas. The gas delivered hereunder shall be measured and metered by the initial Transporter at Seller's sources of gas in accordance with the provisions, specifications and standards set forth in said Transporter's tariff. Each party shall preserve or cause to be preserved for at least one (1) year all test data, charts, allocation statements and other similar records available to it, unless a longer period is prescribed by applicable regulation.
Metering and Measurement. Buyer shall install and maintain the equipment necessary to measure the volume of the Landfill Gas delivered by Seller to Buyer at the Delivery Point, as well as any other information with respect to the Landfill Gas that Seller is required by Applicable Law to capture, monitor or report.
Metering and Measurement. C.1 Processor to Install Meters. Processor will own, maintain, and operate orifice meters or other measuring devices of standard make at or near the Delivery Points. Except as otherwise stated in this Section C, Processor will install orifice meters or other measurement devices and compute volumes in accordance with accepted industry practice. A Party providing compression facilities will also provide sufficient pulsation dampening equipment to prevent pulsation from affecting measurement at the Delivery Points. The Parties will use electronic recording devices. Supplier will have access to Processor’s metering equipment at reasonable hours, but only Processor will calibrate, adjust, operate, and maintain same.
Metering and Measurement. Company will meter the electrical power (demand and energy) delivered to Customer at the point of delivery. In addition, the parties agree to the following testing and corrective procedures:
Metering and Measurement. Company will meter the quantity of natural gas delivered to Customer at the delivery point. Such quantities will be conclusive upon both parties unless such meter is found to be inaccurate by more than two percent, in which case the quantity delivered to Customer shall be determined by calculation, taking into consideration the time of year, the schedule of Customer's operations and other pertinent facts. Company will test the measurement equipment in accordance with applicable state utility commission rules and regulations.
Metering and Measurement. Customer and IHPS accept the quantity, quality, and measurement determined by TDU providing delivery service to Service Location, for purposes of accounting for electricity supplied under this Agreement, in accordance with the terms of the applicable tariff for retail delivery service.
