Laboratory Testing Services Sample Clauses

Laboratory Testing Services. Fully confirmed laboratory-based test for the detection of the EtG biomarker in urine, at a required cut off level of 100 ng/ml. Unit price per test shall include all services and confirmation. Item # Type of Testing Service (As detailed in Section III.G, Scope of Work, Ethyl Glucuronide (EtG) Laboratory Testing Services) Unit Unit Price 3.a EtG /EtS Alcohol Metabolite Testing Per test $4.50
Sample 1Sample 2
AutoNDA by SimpleDocs
Laboratory Testing Services. Applicant has identified a need to conduct certain tests that: (a) require use of a unique or special University facility (the “Laboratory”) that either does not exist elsewhere or is not readily accessible; and (b) involve established, pre-existing methods of a primarily technical nature; and (c) do not constitute original, creative research (clauses (a) – (c) are collectively referred in this Agreement as “Laboratory Tests”). University, through its faculty and staff, will use reasonable efforts to perform the Laboratory Tests identified in one or more SOWs (defined below) which identify the specific testing methods and unique University equipment/facilities to be used and the objectives to be achieved (“Services”), in accordance with and subject to this Agreement. The Services shall be described in one (1) or more properly authorized and executed Statement of Work (each, an “SOW”), which is set forth in substantial form and substance in Exhibit A to this Agreement (“Exhibit A”) and is attached hereto and incorporated in this Agreement by this reference. If a conflict exists between the terms of this Agreement and any SOW, the terms of this Agreement shall govern. University shall not be legally obligated to perform any Services (including, the Laboratory Tests) not set forth in the applicable SOW.
Sample 1
Laboratory Testing Services. The soil/rock samples recovered from the field exploration program will be transported to our Miami laboratory for better classification testing and to determine the pertinent engineering properties for foundation design and site preparation recommendations. Any laboratory testing that may be performed will be limited to soil classification testing. At the completion of the field and laboratory testing services, our Geotechnical Project Engineer will prepare a data report under the direction of a registered Professional Engineer who specializes in geotechnical engineering consulting. The geotechnical data report(s) will contain the following information at a minimum: ❖ Methods and procedures for field sampling and laboratory testing ❖ Test boring logs and classifications ❖ Laboratory test results ❖ Summary of subsurface stratification ❖ Existing groundwater levels and estimated seasonal high and low levels ❖ Distribution and thickness of unsuitable bearing soils (if any) ❖ Any other information deemed appropriate by the Geotechnical Engineer based on our study. The proposed scope of work can be completed within four to eight weeks from the date of authorization of receiving the permit(s) approval, if necessary. Proposal for Geotechnical Services UES Opportunity No. 2130.1021.00017 November 3, 2021 We propose to conduct the geotechnical services for a Lump Sum Fee of $2,239.00. This fee proposal shall remain effective for sixty (60) days. Should you require more than sixty (60) days to formally authorizing us to proceed, we request that you permit us to update our proposal to account for any changes in fees. If you would like us to proceed, please sign and return a copy of the enclosed Work Authorization/Proposal Acceptance Form. UES proposes to provide additional services beyond those listed within this proposal at the following rates. The hourly rates are portal to portal, where applicable for work completed Monday through Friday, 8 a.m. to 5 p.m. Holidays, Weekends, Non-Standard and Overtime hours will be charged at 1.5 times the hourly rates herein with a minimum of 3-hours. Two virtual meetings (up to 4 hours) are included in our lump sum fee. Geotechnical Engineer, per hour $250 Additional SPT Borings, per foot (minimum 40 ft.) $40 Administrative, per hour $65 Reimbursable Expenses such as supplies, printing, etc. Cost + 15% Unforeseen Circumstances due to site conditions such as rig repairs, additional tooling, etc. Cost + 15% Universal Engineering S...
Sample 1
Laboratory Testing Services. The Contractor shall: 4.14.1 Use laboratory testing sites that have either a Clinical Laboratory Improvement Amendments (CLIA) Certificate of Waiver or a Certificate of Registration along with a CLIA identification number. 4.14.2 Verify that laboratories satisfy all requirements in, 42 CFR 493, Subpart A, General Provisions. 4.14.3 Cover laboratory services for diagnostic, screening and monitoring purposes when ordered by the member’s PCP, other attending physician or dentist, and provided by a CLIA approved free-standing laboratory or hospital laboratory, clinic, physician office or other health care facility laboratory. 4.14.4 Require all clinical laboratories to provide verification of CLIA Licensure or Certificate of Waiver during the provider registration process. Failure to do so shall result in either a termination of an active provider ID number or denial of initial registration. 4.14.5 Apply the following requirements to all clinical laboratories: 4.15 Crisis Services Overview Pass-through billing or other similar activities with the intent to avoid the requirements in the Scope of Work, Laboratory Testing Services, is prohibited; Clinical laboratory providers who do not comply with the requirements in the Scope of Work, Laboratory Testing Services, may not be reimbursed; Laboratories with a Certificate of Waiver are limited to providing only the types of tests permitted under the terms of their waiver; Laboratories with a Certificate of Registration are allowed to perform a full range of laboratory tests; Manage and oversee the administration of laboratory services through subcontracts with qualified services providers to deliver laboratory services; Obtain laboratory test data on Title XIX/XXI eligible members from a laboratory or hospital based laboratory subject to the requirements in A.R.S. § 36-2903(Q) (1-6) and (R), upon written request; and Use the data in Contract Section on, Laboratory Testing Services, exclusively for quality improvement activities and health care outcome studies required and approved by AHCCCS. AHCCCS supports a coordinated system of entry into crisis services that are community based, recovery- oriented, and member focused. The improvement of collaboration, data collection standards, and communication will enhance quality of care which leads to better health care outcomes while containing cost. Expanding provider networks that are capable of providing a full array of crisis services that are geared toward the members ...
Sample 1
Laboratory Testing Services. Compression testing of concrete, mortar and grout specimens by ASTM procedures Per Cylinder $ 17.00 Pick-up of test cylinders and transportation to lab (min. 2), or cancellation hours (min. 4) (Does not include vehicle charge) Per hour $ 92.00 Asphalt Maximum Theoretical Specific Gravity Each $ 110.00 Bulk Specific Gravity Each $ 95.00 Ignition Oven Test / Reflux Extraction + Sieve Analysis Each $ 126.00 Core Densities Each $ 45.00 Sieve Analysis (Washed) Each $ 90.00 Sample preparation for the above tests Each $ 40.00 MATERIAL TESTER - 1 - Hand coring and drilling for testing of materials; field inspection of uncured concrete and asphalt. Per Hour $ 98.00 Per Hour Overtime (before 8am, after 5pm and Saturdays) $ 147.00 Per Hour Overtime Sundays and Holidays $ 196.00 EQUIPMENT CHARGES Vehicle Charge - Round Trip Per Day $ 65.00 Nuclear Density Gauge Per Day $ 44.00
Sample 1
Laboratory Testing Services. Maximum Densit y Curve {Modified/Standard Xxxxxxx ASTM 01557/0698) Four-inch mold $279.00/each Six-inch mold $333.00/each Check Point $100.00/each Moisture Content (ASTM D2216L. $21.00/each Moisture Content/Dry Density (ASTM 7263) $20.00/each Unconfined Compression (ASTM D2166L $77.00/each Atterberg Limits Wet Prep Method (ASTM O4318) $250.00/each Atterberg Limits Dry Prep Method (ASTM O4318) $174.00/each Resistance R-Value (ASTM2844/CTM 301) $350.00/each Particle Size Analysis {ASTM C117 and C136} With #200 Wash $115.00/each Bulk Sieve (If Gravelly or >5kg) add $72.00/each % Passing #200 OnlY $83.00/each Sieve Analysis With Hydrometer $196.00/each Organic Content (ASTM 02974> $95.00/each Consolidation Test, Time Rate (ASTM O2435) $403.00/each Consolidation Test, Without Time Rate $200.00/each Expansion Index (ASTM O4829) $420.00/each Swell Pressure $300.00/each Concrete Compression (ASTM C39) $60/cylinder Hot Mix Asphalt Testing {Outside Laboratory) Steel Testing {Outside Laboratory} Outside Laboratory Testing Cost + 20 %
Sample 1
Laboratory Testing Services. Unit Weight of Cores - Core $ 50.00 Xxxxxxxx Stability & Flow - Test $ 245.00 Extraction and Gradation Tests - Test $ 245.00 Torque Wrench per day $ 110.00 Project Engineer per hour $ 110.00 Sr. Engineering Technician per hour $ 95.00 Licensed Building Inspector $ 95.00 Special Inspector $ 95.00 Threshold Inspector $ 95.00 Mobilization & Demobilization of Drilling Crew and Equipment $ 400.00 Layout of Boring Locations, and Coordination of Underground Utility Locating per hour $ 90.00 From Surface to depths of 25 feet $ 18.00 From 26 to 50 feet $ 19.00 From 51 to 75 feet $ 20.00 From 76 to 100 feet $ 24.00 Soil/Rock (N-values greater than 50) per foot $ 9.00 Continuous SPT Testing and Sampling per sample $ 26.00 Auger Borings (ASTM D1452) per foot $ 13.00 Muck Probings per technician per day $ 650.00 Soil per foot $ 13.00 Rock per foot $ 15.00 Shelby Tube per sample $ 195.00 Fixed Piston per sample $ 150.00 Dutch Cone Soundings per foot $ 16.00 Piezocone Soundings foot $ 16.00 Standby Time (per crew hour) per hour $ 160.00 Borehole Grouting and Sealing per hour plus materials $ 160.00 Furnish, Install, and Remove Casing per foot $ 13.00 Materials Cost Plus 15% Barge Drilling Mobilization of Spud Barge (lump sum) TBD per Project Barge Rental per day TBD per Project From surface to depths of 25 feet TBD per Project From 26 to 50 feet TBD per Project Installation of Piezometers and Observation Xxxxx; 2” Diam PVC (0 to 50 feet) per foot $ 45.00 Permanent Groundwater Monitoring Xxxxx of Polluted Soil and Groundwater (2” Diam PVC) From surface to depths of 50 feet $ 75.00 Protective Well Covers, Pads, and Manholes per well $ 325.00 SFWMD Exfiltration Test $ 600.00 Borehole Permeability Test $ 600.00 Double Ring Infiltrometer Test $ 700.00 Holiday/Overtime (OT): Overtime rate is 1.5 times the normal rate and Holiday is 2 times the normal rate. Overtime/Holiday rates would apply only if the City requests services on Weekends, City Holidays, or requests field services to occur before 7 A.M. EST or after 5 P.M. EST. Applies only to technicians and inspectors. Invoices for services shall be submitted once per month, by the tenth (10th) day of each month, and payments shall be made within twenty (20) business days, unless Consultant has chosen to take advantage of the Purchasing Card Program, which guarantees payment within several days. Payments shall be made within twenty (20) business days of receipt of Consultant’s valid invoice, provided that the invoice is accomp...
Sample 1
AutoNDA by SimpleDocs
Laboratory Testing Services. Contractor shall provide the laboratory services to conduct PCR and/or serological testing of all test samples collected by the Contractor’s mobile/community testing teams and the Contractor’s CFTTs. At LDH’s request, Contractor may further provide laboratory services to conduct testing of test samples not collected by Contractor’s testing teams but only to the extent that Contractor determines that Contractor’s laboratory has capacity to do so and Contractor so notifies LDH.
Sample 1

Related to Laboratory Testing Services

  • Laboratory Services Covered Services include prescribed diagnostic clinical and anatomic pathological laboratory services and materials when authorized by a Member's PCP and HPN’s Managed Care Program.

  • Hosting Services 13.1 If Supplier or its subcontractor, affiliate or any other person or entity providing products or services under the Contract Hosts Customer Data in connection with an Acquisition, the provisions of Appendix 1, attached hereto and incorporated herein, apply to such Acquisition. 13.2 If the Hosting of Customer Data by Supplier or its subcontractor, affiliate or any other person or entity providing products or services under the Contract contributes to or directly causes a Data Breach, Supplier shall be responsible for the obligations set forth in Appendix 1 related to breach reporting requirements and associated costs. Likewise if such Hosting contributes to or directly causes a Security Incident, Supplier shall be responsible for the obligations set forth in Appendix 1, as applicable. 14 Change Management

  • Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].

  • Marketing Services The Manager shall provide advice and assistance in the marketing of the Vessels, including the identification of potential customers, identification of Vessels available for charter opportunities and preparation of bids.

  • Performance Testing 7.2.1 The Design-Builder shall direct and supervise the tests and, if necessary, the retests of the Plant using Design-Builder’s supervisory personnel and the Air Emissions Tester shall conduct the air emissions test, in each case, in accordance with the testing procedures set forth in Exhibit A (the “Performance Tests”), to demonstrate, at a minimum, compliance with the Performance Guarantee Criteria. Owner is responsible for obtaining Air Emissions Tester and for ensuring Air Emissions Tester’s timely performance. Design-Builder shall cooperate with the Air Emissions Tester to facilitate performance of all air emissions tests. Design-Builder shall not be held responsible for the actions of Owner’s employees and third parties involved in the Performance Testing, including but not limited to Air Emissions Tester. 7.2.2 No later than thirty (30) Days prior to the earlier of the Scheduled Substantial Completion Date or Substantial Completion, Design-Builder shall provide to Owner for review a detailed testing plan for the Performance Tests (other than for air emissions). Owner and Design-Builder shall agree upon a testing plan that shall be consistent with the Performance Test Protocol contained in Exhibit A hereto. After such agreement has been reached, Design-Builder shall notify the Owner five (5) business days prior to the date Design-Builder intends to commence the Performance Tests and shall notify the Owner upon commencement of the Performance Tests. Owner and Independent Engineer each have the right to witness all testing, including the Performance Tests and any equipment testing, whether at the Site or at the Subcontractor’s or equipment supplier’s premises during the course of this Agreement. Notwithstanding the foregoing sentence, Owner shall bear the costs of providing a witness to any such testing and all such witnesses shall comply at all times with Design-Builder’s, Subcontractor’s or equipment supplier’s safety and security procedures and other reasonable requirements, and otherwise conduct themselves in a manner that does not interfere with Design-Builder’s, Subcontractor’s or equipment supplier’s activities or operations. 7.2.3 Design-Builder shall provide to Owner a Performance Test report (excluding results from air emissions testing), including all applicable test data, calculations and certificates indicating the results of the Performance Tests and, within five (5) business days of Owner’s receipt of such results, Owner, Independent Engineer and Design-Builder will jointly inspect such Work and review the results of the Performance Tests to verify that the Performance Guarantee Criteria have been met. If Owner or Independent Engineer reasonably determines that the Performance Guarantee Criteria have not been met, Owner shall notify Design-Builder the reasons why Owner determined that the Performance Guarantee Criteria have not been met and Design-Builder shall promptly take such action or perform such additional work as will achieve the Performance Guarantee Criteria and shall issue to the Owner another notice in accordance with Section 7.2.2; provided however that if the notice relates to a retest, the notice may be provided no less than two (2) business days prior to the Performance Tests. Such procedure shall be repeated as necessary until Owner and Independent Engineer verifies that the Performance Guarantee Criteria have been met. 7.2.4 If Owner, for whatever reason, prevents Design-Builder from demonstrating the Performance Guarantee Criteria within thirty (30) Days of Design-Builder’s notice that the Plant is ready for Performance Testing, then Design-Builder shall be excused from demonstrating compliance with the Performance Guarantee Criteria during such period of time that Design-Builder is prevented from demonstrating compliance with the Performance Guarantee Criteria; provided however that Design-Builder will be deemed to have fulfilled all of its obligations to demonstrate that the Plant meets the Performance Guarantee Criteria should such period of time during which Design-Builder is prevented from demonstrating the Performance Criteria exceed thirty (30) Days or extend beyond the Final Completion Date.

  • Engineering Services Definition: Engineering Services includes any service or creative work, the adequate performance of which requires education, training and experience in the application of special knowledge in consulting, investigating, evaluating, planning and designing, engineering principles. Engineering Services covered by the Xxxxxx Architect-Engineers Act (40 U.S.C. 1102) are not covered in the primary scope of OASIS SB. Examples: Service areas that are included under the Engineering Services discipline include, but are not limited to the following: 1. Systems Engineering 2. Advanced Technology Pilots and Trials 3. Alternative Energy Sources and Engineering 4. Configuration Management 5. Concept Development

  • Support Services Rehabilitation, counselling and EAP’s. Support is strictly non- punitive, and can be accessed at anytime (self-identification of the need for help is strongly encouraged).

  • Performance Tests Contractor shall perform Performance Tests in accordance with Section 11.2 of the Agreement and Attachment S.

  • Training Services Training Services may include pre-packaged training Products, and/or the development or customization of training programs as requested, including Live Training, Computer Based/Multi-Media Training which encompasses Internet-Delivered Training, and/or Video Based Training.

  • Diagnostic Services All necessary procedures to assist the dentist in evaluating the existing conditions to determine the required dental treatment, including: Oral examinations Consultations

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!