Maintenance, Technical Faults and Fault Elimination. 5.1 The 2 parties shall conduct network maintenance and guarantee normal operation of the entire network in line with relevant rules published from time to time by state communications authority.
Maintenance, Technical Faults and Fault Elimination Sample Clauses
Related to Maintenance, Technical Faults and Fault Elimination
Warranty Period The warranties set forth in Clauses 12.1.1 and 12.1.2 shall be limited to those defects that become apparent within **** after Delivery of the affected Aircraft (the “Warranty Period”).
Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).
Patent Maintenance All annuity and maintenance fees that are necessary in order to keep the Patents in force as of the Effective Date have been paid by Seller, and no payment of annuities or fees, or papers to be filed in patent offices, are required to be made within the three-month period after the Effective Date.
Support and Maintenance RSA agrees to provide the maintenance and support specified in this Support Agreement and You agree to pay RSA's then-current annual support fee ("Support Fee").
System Maintenance The Trust understands that USBFS will perform periodic maintenance to the System(s), which may cause temporary service interruptions. To the extent possible, USBFS shall notify the Trust of all planned outages and will perform any necessary maintenance during non-business hours.
USE AND MAINTENANCE Except as may be otherwise specified on any Schedule, (a) Lessee shall (1) use the Equipment solely in the continental United States and in the conduct of its business, for the purpose for which the Equipment was designed, in a careful and proper manner, and shall not permanently discontinue use of the Equipment; (2) operate, maintain, service and repair the Equipment, and maintain all records and other materials relating thereto, (A) in accordance and consistent with (i) all maintenance and operating manuals or service agreements, whenever furnished or entered into, including any subsequent amendments or replacements thereof, issued by the supplier or service provider, (ii) the requirements of all applicable insurance policies, (iii) manufacturer’s recommendations, (iv) the original purchase agreement under which such Equipment was acquired, so as to preserve all of Lessee’s and Lessor’s rights thereunder, including all rights to any warranties, indemnities or other rights or remedies, as and if applicable, (v) all applicable laws, and (vi) the prudent practice of other similar companies in the same business as Lessee, but in any event, to no lesser standard than that employed by Lessee for comparable equipment owned or leased by it; and (B) without limiting the foregoing, so as to cause the Equipment to be in good repair and operating condition and in at least the same condition as when delivered to Lessee hereunder, except for ordinary wear and tear resulting despite Lessee's full compliance with the terms hereof; (3) provide written notice to Lessor not less than thirty (30) days after any change of the location of any Equipment (or the location of the principal garage of any Equipment, to the extent that such Equipment is mobile equipment) as specified in the Schedule; and (4) not attach or incorporate the Equipment into any property except for other Equipment in such a manner that the Equipment may be deemed to have become an accession to or a part of such other property. (b) Within a reasonable time, Lessee will replace any parts of the Equipment which become worn out, lost, destroyed, damaged beyond repair or otherwise unfit for use, by new or reconditioned replacement parts which are free and clear of all Liens and have a value, utility and remaining useful life at least equal to the parts replaced (assuming that they were in the condition required by this Lease). Any modification or addition to the Equipment that is required by this Lease shall be made by Lessee. An interest in all such parts, modifications and additions to the Equipment immediately shall vest in Lessor, without any further action by Lessor or any other person, and they shall be deemed incorporated in the Equipment for all purposes of the related Schedule. Unless replaced in accordance with this Section, Lessee shall not remove any parts originally or from time to time attached to the Equipment, if such parts are essential to the operation of the Equipment, are required by any other provision of this Lease or cannot be detached from the Equipment without interfering with the operation of the Equipment or adversely affecting the value, utility and remaining useful life which the Equipment would have had without the addition of such parts. Except as permitted in this Section, Lessee shall not make any material alterations to the Equipment. (c) Lessee shall afford Lessor and/or its designated representatives immediate access to the premises where the Equipment is located for the purpose of inspecting and appraising such Equipment and all applicable maintenance or other records relating thereto at any time during normal business hours, at Lessee’s sole cost and expense. If any discrepancies are found as they pertain to the general condition of the Equipment, Lessor will communicate these discrepancies to Lessee in writing. Lessee shall then have thirty (30) days to rectify these discrepancies at its sole expense. Lessee shall pay all expenses of a re-inspection by Lessor’s appointed representative, including travel costs.
Aircraft Maintenance Operator shall, at its own expense, cause the Aircraft to be inspected, maintained, serviced, repaired, overhauled, and tested in accordance with FAR Part 91 so that the Aircraft will remain in good operating condition and in a condition consistent with its airworthiness certification and shall take such requirements into account in scheduling the Aircraft hereunder, including but not limited compliance with applicable airworthiness directives and service bulletins. Performance of maintenance, preventive maintenance or inspection shall not be delayed or postponed for the purpose of scheduling the Aircraft unless such maintenance or inspection can safely be conducted at a later time in compliance with applicable laws, regulations and requirements, and such delay or postponement is consistent with the sound discretion of the pilot-in-command. In the event that any non-standard maintenance is required during the term and will interfere with User’s requested or scheduled flights, Operator, or Operator’s pilot-in-command, shall notify User of the maintenance required, the effect on the ability to comply with User’s requested or scheduled flights and the manner in which the parties will proceed with the performance of such maintenance and conduct of such flight(s). In no event shall Operator be liable to User or any other person for loss, injury or damage occasioned by the delay or failure to furnish the Aircraft under this Agreement, whether or not maintenance-related.
Repairs and Maintenance Grantor agrees to keep and maintain, and to cause others to keep and maintain, the Collateral in good order, repair and condition at all times while this Agreement remains in effect. Grantor further agrees to pay when due all claims for work done on, or services rendered or material furnished in connection with the Collateral so that no lien or encumbrance may ever attach to or be filed against the Collateral.
Software Maintenance The Vendor represents and warrants that the Software delivered to the escrow agent pursuant to subsection 11.7 for redelivery to the Owner pursuant to the Escrow Agreement will be in a form suitable for reproduction by the Owner and will include the full Source Code language statement of the Software as used by the Vendor sufficient to allow maintenance and modification.
Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.
