Measurement of Lignite Quantities Sample Clauses

Measurement of Lignite Quantities. The lignite unloading and handling facilities to be located at the Point of Delivery, including the truck dump, shall be designed, constructed, owned, maintained and operated by Buyer at its sole risk and expense. Buyer shall determine the quantities of lignite delivered by Seller by means of a belt scale (the “Pay Scale”) to be designed, constructed, owned, maintained and operated by Buyer at its sole risk and expense, except for calibration as noted below, in accordance with standards recommended by the equipment manufacturer, and agreed to by the Parties, as may be amended from time to time. If such standards are discontinued, the Parties shall continue to use the last effective standards and shall use reasonable efforts to find and agree to replacement standards. If the Parties are unable to agree, the matter shall be submitted to Arbitration. The last effective standards shall remain effective until the matter is resolved either by agreement or Arbitration. Seller shall have the right to review and comment on the designs of the unloading and handling facilities, and the Parties agree to use reasonable efforts to coordinate design and equipment selection for lignite delivery unloading and handling. Seller also shall have the right to install a check scale on the conveyor belts at Seller's sole risk and expense (the “Check Scale”). Seller shall be obligated to operate, maintain and calibrate the Check Scale in accordance with standards recommended by the equipment manufacturer and agreed to by the Parties.
Sample 1Sample 2
AutoNDA by SimpleDocs

Related to Measurement of Lignite Quantities

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).

  • Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.

  • Product Quality (a) Tesoro warrants that all Products delivered under this Agreement or any Purchaser Order shall meet the latest applicable pipeline specifications for that Product upon receipt at the applicable Terminal and contain no deleterious substances or concentrations of any contaminants that may make it or its components commercially unacceptable in general industry application. Tesoro shall not deliver to any of the Terminals any Products which: (a) would in any way be injurious to any of the Terminals; (b) would render any of the Terminals unfit for the proper storage of similar Products; (c) would contaminate or otherwise downgrade the quality of the Products stored in commingled storage; (d) may not be lawfully stored at the Terminals; or (e) otherwise do not meet applicable Product specifications for such Product that are customary in the location of the Terminal. If, however, there are Products that do not have such applicable specifications, the specifications shall be mutually agreed upon by the Parties. Should Tesoro's commingled Products not meet or exceed the minimum quality standards set forth in this Agreement or any applicable Purchase Order, Tesoro shall be liable for all loss, damage and cost incurred thereby, including damage to Products of third parties commingled with Tesoro's unfit Products.

  • Service Quality The Transfer Agent shall maintain a quality control process designed to provide a consistent level of quality and timeliness for its call center, correspondence services and transaction processing.

  • Product Specifications The Company agrees that all Products sold to Xxxx hereunder shall conform to the respective specifications set forth on Schedule A or to such other specifications as are from time to time agreed upon by the Parties.

  • Delivery Points The measurement of and tests for quality of Shipper's Gas redelivered at the Delivery Points shall be governed by and determined in accordance with the requirements of the receiving pipeline at each Delivery Point.

  • Delivery Point Once Manufacture of the Products has been completed, Contractor shall be responsible for delivering the Finished Goods FCA, (as defined in Incoterms (2000) published by the International Chamber of Commerce) and to a freight forwarder specified by Company in its Order, or otherwise approved by Company. “Delivery Point” as used in this Agreement shall mean the specific time and location that the Product is delivered to the shipper specified on the Order.

  • Delivery Schedule The scheduled months of delivery of the Aircraft are listed in the attached Table 1. Exhibit B describes certain responsibilities for both Customer and Boeing in order to accomplish the delivery of the Aircraft.

  • Rolling Forecasts The parties shall cooperate in good faith to develop rolling twelve (12) month (by Product and pack type), non-binding order forecasts of Buyer’s needs for the Products. The parties shall use commercially reasonable efforts to provide such forecasts at least ten (10) business days prior to the start of the applicable month.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!