No Target Date for Settlement Sample Clauses

No Target Date for Settlement. The Vendor gives no warranty to the Purchaser as to when the title to the Lot will issue or when the Plans will be deposited in the Otago Registry of the Land Titles Office, or as to when the Purchaser will be able to register a memorandum of transfer of the Lot from the Vendor. The Purchaser acknowledges that any anticipated or projected dates for Settlement given by the Vendor or its agents prior to or after signing this agreement are indicative and approximations only and are not binding on the Vendor or can not give rise to any claim for compensation by the Purchaser.
Sample 1
AutoNDA by SimpleDocs

Related to No Target Date for Settlement

  • EFFECTIVE DATE OF SETTLEMENT 38. The Effective Date of this Settlement shall be the first business day on which all of the following shall have occurred or been waived:

  • PROCEDURES FOR SUPPLEMENTAL PAYMENT CALCULATIONS All calculations required by this Article VI, including but not limited to: (i) the calculation of the Applicant’s Stipulated Supplemental Payment Amount; (ii) the determination of both the Annual Limit and the Aggregate Limit; (iii) the effect, if any, of the Aggregate Limit upon the actual amount of Supplemental Payments eligible to be paid to the District by the Applicant; and (iv) the carry forward and accumulation of any of the Applicant’s Stipulated Supplemental Payment Amounts unpaid by the Applicant due to the Aggregate Limit in previous years, shall be calculated by the Third Party selected pursuant to Section 4.3.

  • Effective Date of Settlements ‌ Settlements reached at any step of the grievance procedure in this article, other than Clause 8.11, shall be applied retroactively to the date of the occurrence of the action or situation which gave rise to the grievance, but not prior to the effective date of the agreement in effect at the time of the occurrence or the date set by a board of arbitration.

  • Deadline for Submission of Bids 19.1 Bids must be received by the Purchaser at the address specified under ITB Clause 18.2 no later than the time and date specified in the Bid Data Sheet. 19.2 The Purchaser may, at its discretion, extend this deadline for the submission of bids by amending the bidding documents in accordance with ITB Clause 7, in which case all rights and obligations of the Purchaser and bidders previously subject to the deadline will thereafter be subject to the deadline as extended.

  • Sole Source as Grounds for Rejection of a Change Order If a Change Order is submitted to Contractor for the purposes of adding a Bulletin to this Contract and said Bulletin designates a Sole Source from which Contractor is required to procure goods or services necessary to perform the Work, which Sole Source has not been designated previously, Contractor shall be entitled to reject the proposed Change Order if the designated Sole Source refuses to provide to Contractor the warranties, bonds, terms or schedule required under the Contract Documents, including any warranty or terms or schedule required by Bulletins referenced in the proposed Change Order. In such event, Contractor shall give written notice to the Owner rejecting the proposed Change Order and, if possible, shall accompany said written notice with a proposal from Contractor for changes or modifications to the Bulletin so as to eliminate the Sole Source designation but to achieve goods or services equal in quality or function. The Owner may then require the Design Professional to revise the subject Bulletin so as to eliminate the designation of the Sole Source by incorporation of Contractor's proposal or otherwise. Upon revision of the Bulletin by the Design Professional and approval thereof by the Owner, the Owner shall again submit to the Contractor a proposed Change Order for the purpose of adding the revised Bulletin to this Contract. If the Owner decides to retain the Sole Source in the Change Order and Contractor cannot acquire the full contractually required warranties from the Sole Source, Contractor shall be held only to the warranty terms and schedule obtainable from the Sole Source.

  • CLEC to CLEC Conversions for Unbundled Loops 2.1.11.1 The CLEC to CLEC conversion process for Loops may be used by ITC^DeltaCom when converting an existing Loop from another CLEC for the same End User. The Loop type being converted must be included in ITC^DeltaCom’s Agreement before requesting a conversion.

  • PROCEDURE FOR APPROVAL OF SETTLEMENT 28. Acceptance of this Settlement Agreement shall be sought at a hearing of the Central Regional Council of the MFDA on a date agreed to by counsel for Staff and the Respondent.

  • TERMS OF SETTLEMENT 26. The Respondent agrees to the following terms of settlement:

  • Final Settlement Approval 4.1 No later than ten (10) business days before the Fairness Hearing, Class Counsel shall submit to the Court a motion for entry of the Final Order (Exhibit 5) in the form approved by Class Counsel and Defense Counsel, which shall request approval by the Court of the terms of this Settlement Agreement and entry of the Final Order in accordance with this Settlement Agreement. The Final Order as proposed by the Settling Parties shall provide for the following, among other things, as is necessary to carry out the Settlement consistent with applicable law and governing Plan documents:

  • Full and Final Settlement 21.1 This agreement is in full and final settlement of all Union or employee claims relating to employee rights and entitlements. Accordingly, the Union or employees shall not pursue any extra claims, nor take any industrial or protest action concerning any matter explicitly or implicitly dealt with in this agreement.

Time is Money Join Law Insider Premium to draft better contracts faster.