Overload A regular employee who works an overload in a given year shall receive no less than either: (a) the pro-rata salary for the overload based on the Provincial Salary Scale or the secondary scale on which the employee is placed or (b) a reduction of workload in a subsequent year that is commensurate with the amount of the overload. The conditions governing overloads are as set out in the regular employee’s local collective agreement, subject to the above provision.
Noise The Hirer shall ensure that the minimum of noise is made on arrival and departure, particularly late at night and early in the morning. The Hirer shall, if using sound amplification equipment, make use of any noise limitation device provided at the premises and comply with any other licensing condition for the premises.
Electrical Provide drawings for the following systems: .1 Lighting including circuiting and luminaire identification and switching. Also provide illuminance computer printout for all indoor typical indoor spaces and parking lots. .2 Convenience outlets and circuiting, special outlets and circuiting, television outlets, and power systems and equipment. Provide riser diagrams for all electrical systems including master clock, intercom, fire alarm, ITV, computer networking/telephone. Also, provide for emergency and normal power distribution. Provide luminaire schedule. .3 Panel schedule may be in preliminary form but circuitry must be included. .4 Applicable installation details. .5 General legend and list of abbreviations. .6 Voltage drop computation for all main feeders. .7 Short circuit analysis .8 Provide 1/2" scale floor plan and wall elevations for all electrical rooms.
Walls 12 Developer shall provide rustication patterns on all walls, except drainage headwalls, in Aesthetic 13 Area 3 in accordance with Exhibit L2.24 of the LAADCR. The final designs shall resemble these 14 simulations.
Structural 3.4.1. Layout structural systems with dimensions and floor elevations. Identify structural systems (including pre-cast, structural steel with composite deck, structural steel bar joists); with preliminary sizing identified. 3.4.2. Identify foundation systems (including fill requirements, piles, caissons, spread footings); with preliminary sizing identified.
Floor Load Tenant shall not place a load upon any floor of the Premises that exceeds 50 pounds per square foot “live load”. Landlord reserves the right to reasonably designate the position of all Equipment which Tenant wishes to place within the Premises, and to place limitations on the weight thereof.
Plumbing fixtures and appliances shall be used only for the purposes for which designed, and no sweepings, rubbish, rags or other unsuitable material shall be thrown or deposited therein. Damage resulting to any such fixtures or appliances from misuse by a tenant or its agents, employees or invitees, shall be paid by such tenant.
Fences Except for establishment cost incurred by the United States and replacement cost not due to the Landowner’s negligence or malfeasance, all other costs involved in maintenance of fences and similar facilities to exclude livestock are the responsibility of the Landowner. The installation or use of fences which have the effect of preventing wildlife access and use of the Easement Area are prohibited on the Easement Area, easement boundary, or on the Landowner’s land that is immediately adjacent to, and functionally related to, the Easement Area.
Ceilings 13.1 Lambdaboard ceilings, minimum 25mm thick with a width of 1220mm x 1800mm, skimmed with Plascon EZ Joint and EZ Skim system. 13.2 Cornices to be Nucornice polystyrene core cove cornice as per Everite or similar approved. Xxxx Shadow line cornices will be at extra cost if required.
Visibility 1. Unless the Council of Europe requests or agrees otherwise, the Grantee shall take all necessary measures to publicise the fact that the Action has been funded within the framework of a Joint Project between the European Union and the Council of Europe. Information given to the press and to the beneficiaries of the Action, all related publicity material, official notices, reports and publications, shall acknowledge that the Action was carried out with a grant from a Joint Project between the European Union and the Council of Europe and shall display in an appropriate way the Joint Projects’ visual identity (for instructions on use of the Joint Projects’ visual identity, see Appendix IV). 2. In cases where equipment or major items have been purchased using funds provided by the European Union or the Council of Europe, the Grantee shall indicate this clearly on that equipment and those major items (including display of the European Union and Council of Europe’s logos), provided that such actions do not jeopardise the safety and security of the Grantee’s staff. 3. The acknowledgement and Joint Projects’ visual identity shall be clearly visible in a manner that will not create any confusion regarding the identification of the Acton as a project of the Grantee and the ownership of the equipment and items by the Grantee. 4. All publications by the Grantee pertaining to the Action that have received funding from a Joint Project between the European Union and the Council of Europe, in whatever form and whatever medium, including the Internet, shall carry the following or a similar disclaimer: “This document has been produced using funds of a Joint Project between the European Union and the Council of Europe. The views expressed herein can in no way be taken to reflect the official opinion of the European Union or the Council of Europe”. 5. If the equipment purchased with a grant from a Joint Project is not transferred to the local partners of the Grantee or to the final recipient of the Action at the end of the implementation period of this Agreement, the visibility requirements as regards this equipment shall continue to apply between the end of the implementation period of this Agreement and the end of the Joint Project, if the latter lasts longer. 6. All layouts of any communication items prepared by the Grantee are subject to approval with the Contact point within the Council of Europe. 7. The Grantee accepts that the European Union and the Council of Europe may publish in any form and medium, including on their websites, the name and address of the Grantee, the purpose and amount of the grant and, if relevant, the percentage of co-financing.
