PROCEDURE FOR "H" POINT AND ACTUAL TORSO ANGLE DETERMINATION Sample Clauses

PROCEDURE FOR "H" POINT AND ACTUAL TORSO ANGLE DETERMINATION. 4.1. The vehicle shall be preconditioned at the manufacturer's discretion, at a temperature of 20  10C to ensure that the seat material reached room temperature. If the seat to be checked has never been sat upon, a 70 to 80 kg person or device shall sit on the seat twice for one minute to flex the cushion and back. At the manufacturer's request, all seat assemblies shall remain unloaded for a minimum period of 30 min prior to installation of the 3-D H machine. 4.2. The vehicle shall be at the measuring attitude defined in paragraph 2.11. above. 4.3. The seat, if it is adjustable, shall be adjusted first to the rearmost normal driving or riding position, as indicated by the vehicle manufacturer, taking into consideration only the longitudinal adjustment of the seat, excluding seat travel used for purposes other than normal driving or riding positions. Where other modes of seat adjustment exist (vertical, angular, seat-back, etc.) these will then be adjusted to the position specified by the vehicle manufacturer. For suspension seats, the vertical position shall be rigidly fixed corresponding to a normal driving position as specified by the manufacturer. 4.4. The area of the seating position contacted by the 3-D H machine shall be covered by a muslin cotton, of sufficient size and appropriate texture, described as a plain cotton fabric having 18.9 threads per cm2 and weighing 0.228 kg/m2 or knitted or non-woven fabric having equivalent characteristics. If the test is run on a seat outside the vehicle, the floor on which the seat is placed shall have the same essential characteristics 2/ as the floor of the vehicle in which the seat is intended to be used. 4.5. Place the seat and back assembly of the 3-D H machine so that the centreplane of the occupant (C/LO) coincides with the centreplane of the 3-D H machine. At the manufacturer's request, the 3-D H machine may be moved inboard with respect to the C/LO if the 3-D H machine is located so far outboard that the seat edge will not permit levelling of the 3-D H machine. 4.6. Attach the foot and lower leg assemblies to the seat pan assembly, either individually or by using the T-bar and lower leg assembly. A line through the "H" point sight buttons shall be parallel to the ground and perpendicular to the longitudinal centreplane of the seat. 4.7. Adjust the feet and leg positions of the 3-D H machine as follows: 4.7.1. Designated seating position: driver and outside front passenger 4.7.1.1. Both feet and leg as...
Sample 1
PROCEDURE FOR "H" POINT AND ACTUAL TORSO ANGLE DETERMINATION. 4.1. The vehicle shall be preconditioned at the manufacturer's discretion, at a temperature of 20 ± 10°C to ensure that the seat material reached room temperature. If the seat to be checked has never been sat upon, a 70 to 80 kg person or device shall sit on the seat twice for one minute to flex the cushion and back. At the manufacturer's request, all seat assemblies shall remain unloaded for a minimum period of 30 min prior to installation of the 3-D H machine. 4.2. The vehicle shall be at the measuring attitude defined in paragraph 2.11. above.
Sample 1

Related to PROCEDURE FOR "H" POINT AND ACTUAL TORSO ANGLE DETERMINATION

  • CERTIFICATION OF INDEPENDENT PRICE DETERMINATION By submission of this bid, the Bidder certifies, and in the case of a joint bid each party thereto certifies as to its own organization, that in connection with this procurement: A. The prices in this bid have been arrived at independently, without consultation, collusion, communication, or agreement for the purpose of restricting competition, as to any matter relating to such prices with any other bidder or with any competitor. B. Unless otherwise required by law, the prices which have been quoted in this bid have not been knowingly disclosed by the Bidder and will not knowingly be disclosed by the Bidder prior to opening, directly or indirectly to any other Bidder or to any competitor; and, C. No attempt has been made or shall be made by the Bidder to induce any other person or bidder to submit or not to submit a bid for the purpose of restricting competition.

  • DEVELOPMENT OR ASSISTANCE IN DEVELOPMENT OF SPECIFICATIONS REQUIREMENTS/ STATEMENTS OF WORK

  • Technical Feasibility of String While ICANN has encouraged and will continue to encourage universal acceptance of all top-­‐level domain strings across the Internet, certain top-­‐level domain strings may encounter difficulty in acceptance by ISPs and webhosters and/or validation by web applications. Registry Operator shall be responsible for ensuring to its satisfaction the technical feasibility of the TLD string prior to entering into this Agreement.

  • PROCEDURE FOR NOTIFICATION AND APPLICATION FOR INDEMNIFICATION (a) Indemnitee agrees to notify promptly the Company in writing upon being served with any summons, citation, subpoena, complaint, indictment, information or other document relating to any Proceeding, claim, issue or matter therein which may be subject to indemnification, hold harmless or exoneration rights, or advancement of Expenses covered hereunder. The failure of Indemnitee to so notify the Company shall not relieve the Company of any obligation which it may have to Indemnitee under this Agreement, or otherwise. (b) Indemnitee may deliver to the Company a written application to indemnify, hold harmless or exonerate Indemnitee in accordance with this Agreement. Such application(s) may be delivered from time to time and at such time(s) as Indemnitee deems appropriate in his or her sole discretion. Following such a written application for indemnification by Indemnitee, Indemnitee’s entitlement to indemnification shall be determined according to Section 12(a) of this Agreement.

  • HHS Single Audit Unit will notify Grantee to complete the Single Audit Determination Form If Grantee fails to complete the form within thirty (30) calendar days after receipt of notice, Grantee maybe subject to sanctions and remedies for non-compliance.

  • Independent Evaluation Buyer is an experienced and knowledgeable investor in the oil and gas business. Buyer has been advised by and has relied solely on its own expertise and legal, tax, title, reservoir engineering, environmental and other professional counsel concerning this transaction, the Properties, the value thereof and title thereto.

  • Purpose; Incorporation by Reference of Auction Procedures and Settlement Procedures (a) On each Auction Date, the provisions of the Auction Procedures will be followed by the Auction Agent for the purpose of determining the Applicable Rate for the of APS, for the next Dividend Period therefor. Each periodic operation of such procedures is hereinafter referred to as an "Auction." (b) All of the provisions contained in the Auction Procedures and the Settlement Procedures are incorporated herein by reference in their entirety and shall be deemed to be a part of this Agreement to the same extent as if such provisions were set forth fully herein. (c) BD agrees to act as, and assumes the obligations of and limitations and restrictions placed upon, a Broker-Dealer under this Agreement. BD understands that other Persons meeting the requirements specified in the definition of "Broker-Dealer" contained in Paragraph 10 of Article VII of the Amended By-laws may execute a Broker-Dealer Agreement and participate as Broker-Dealers in Auctions. (d) BD and other Broker-Dealers may participate in Auctions for their own accounts. However, the Trust, by notice to BD and all other Broker Dealers, may prohibit all Broker-Dealers from submitting Bids in Auctions for their own accounts, provided that Broker-Dealers may continue to submit Hold Orders and Sell Orders.

  • Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.

  • Presentation of Potential Target Businesses The Company shall cause each of the Initial Shareholders to agree that, in order to minimize potential conflicts of interest which may arise from multiple affiliations, the Initial Shareholders will present to the Company for its consideration, prior to presentation to any other person or company, any suitable opportunity to acquire an operating business, until the earlier of the consummation by the Company of a Business Combination or the liquidation of the Company, subject to any pre-existing fiduciary obligations the Initial Shareholders might have.

  • Office of Inspector General Investigative Findings Expert Review In accordance with Senate Bill 799, Acts 2021, 87th Leg., R.S., if Texas Government Code, Section 531.102(m-1)(2) is applicable to this Contract, Contractor affirms that it possesses the necessary occupational licenses and experience.