Propeller Blade Replacement. (Category B)
Propeller Blade Replacement Sample Clauses
Related to Propeller Blade Replacement
REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.
Replacement Parts Replacement parts for goods purchased by Buyer are for the purpose of this Section defined as “Parts” (and are also considered “goods” under this Order). Unless specified otherwise by Buyer in writing, Supplier shall provide Parts (or upon Buyer’s written consent, an alternative replacement part that provides the same form, fit and function as the Part(s)) for a period of twenty (20) years after production of the goods (into which the applicable Parts are incorporated) ceases. Supplier shall continue to supply such Parts past the twenty (20) year period if Buyer orders at least twenty (20) Parts per year during such twenty-year period. The prices for any Parts purchased in the first two (2) years of the twenty-year period shall not exceed those prices in effect at the time production of the goods ceases, and no set up charges shall be permitted by Supplier or paid by Xxxxx during this two-year period. Thereafter, the prices for Parts shall be negotiated based on Supplier’s actual cost of production of such Parts plus any special packaging costs. No minimum order requirements shall apply unless the parties mutually agree in advance. After the end of the twenty-year period, Supplier shall continue to maintain in good working condition all Supplier-owned tooling required to produce the Parts and shall not dispose of such tooling without offering Buyer the right of first refusal to purchase such tooling.
Accessories, Spare Parts and Tools 1. In determining whether all the non-originating materials used in the production of a good undergo the applicable change in tariff classification or a specific manufacturing or processing operation set out in Annex 2, accessories, spare parts or tools delivered with the good that form part of the good's standard accessories, spare parts or tools, shall be disregarded, provided that:
Integrated Digital Loop Carriers The feeder portion of some loops may be provide by means of Integrated Digital Loop Carrier (IDLC). IDLC provides a fiber optic cable transmission path that travels directly into BellSouth’s central office local switch. Where BellSouth uses IDLC ,if technically feasible and capacity does exist, BST will provide Al-Call with a Designed DS0 UVL by using alternative provisioning techniques including but not limited to such as “hairpinning” and DAC grooming. Alternative provisioning techniques will be provided at no additional cost to Al-Call . Hairpinning involves providing a DS0 signal from an IDLC-served loop to Al-Call ’s collocation equipment by using a dedicated pathway that traverses BellSouth’s central office switch. BellSouth will provide such DS0 signal to Al-Call by establishing a copper cross connect between the BellSouth switch and Al-Call ’s collocation equipment.
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where InterGlobe has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to InterGlobe. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for InterGlobe (e.g. hairpinning):
Private Aircraft Mileage When an employee is authorized by his/her department, reimbursement for the use of the employee’s privately owned aircraft on State business shall be made at the rate of 50 cents per statute mile. Pilot qualifications and insurance requirements will be maintained in accordance with DPA rule 599.628.1 and the State Office of Risk and Insurance Management.
Spare Parts 14.1 As specified, the supplier may be required to provide any or all of the following materials, notifications, and information pertaining to spare parts manufactured or distributed by the supplier:
Engine A. Any internal repairs or replacement of internal components, or replacement of engine assembly.
Equipment Cleaning (a) Areas, known by Forest Service prior to timber sale advertisement, that are infested with invasive species of concern are shown on Sale Area Map. A current list of invasive species of concern and a map showing the extent of known infestations is available at the Forest Supervisor’s Office. For purposes of this provision, “Off-Road Equipment” includes all logging and construction machinery, except for log trucks, chip vans, service vehicles, water trucks, pickup trucks, cars, and similar vehicles.
SERVICE AND REPLACEMENT PARTS 23.1 During the term of this Contract, Seller will fulfill Buyer's and Customer’s service and replacement parts requirements at the then current production price(s) under this Contract. If the Products are systems or modules, Seller will sell the components or parts that comprise the system or module at price(s) that will not, in the aggregate, exceed the price of the system or module less assembly costs.
