ROAD SHAPING Sample Clauses

ROAD SHAPING. Purchaser shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un‐concentrated manner, and must be uniform, firm, and rut‐free.
Sample 1Sample 2Sample 3See All (29)
AutoNDA by SimpleDocs
ROAD SHAPING. Purchaser shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un‐concentrated manner, and must be uniform, firm, and rut‐free. Purchaser shall accomplish all shaping using a motor grader with a minimum of 175 horsepower.
Sample 1Sample 2Sample 3See All (16)
ROAD SHAPING. Contractor shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un‐concentrated manner, and must be uniform, firm, and rut‐free.
Sample 1
ROAD SHAPING. Contractor shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un-concentrated manner, and must be uniform, firm, and rut-free. Contractor shall accomplish all shaping using a motor grader with a minimum of 175 horsepower.
Sample 1
ROAD SHAPING. DRAFT Purchaser shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un-concentrated manner, and must be uniform, firm, and rut-free 4-56 DRY WEATHER SHAPING The Contract Administrator may require the application of water to facilitate shaping activities. The method of water application is subject to written approval by the Contract Administrator.
Sample 1
ROAD SHAPING. The road subgrade and surface shall be shaped as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape shall ensure runoff in an even, un‐concentrated manner, and shall be uniform, firm, and rut‐free. All grading shall be accomplished using a motor grader with a minimum of 175 horsepower.
Sample 1
ROAD SHAPING. Purchaser shall shape the subgrade and surface as shown on the TYPICAL SECTION SHEET. The subgrade and surface shape must ensure runoff in an even, un−concentrated manner, and must be uniform, firm, and rut−free. 4-60 FILL COMPACTION Purchaser shall compact all embankment and waste material in accordance with the COMPACTION LIST by routing equipment over the entire width of each lift. Waste material may be placed by end−dumping or sidecasting until sufficiently wide enough to support the equipment.
Sample 1
AutoNDA by SimpleDocs

Related to ROAD SHAPING

  • Load Shedding The Distributor may carry out Load Shedding in the following circumstances:

  • Road Surfaces (1) Grade, shape, crown, and/or outslope surface and shoulders.

  • Moonlighting 24.01 The Company and the Union agree in principle to eliminate the practice commonly referred to as moonlighting.

  • ROAD DIMENSIONS Purchaser shall perform road work in accordance with the dimensions shown on the TYPICAL SECTION SHEET and the specifications within this road plan.

  • Advertising The Contractor shall not refer to sales to the State for advertising or promotional purposes, including, but not limited to, posting any material or data on the Internet, without DAS’s prior written approval.

  • Lodging Board members should request conference rate or mid-fare room accommodations. A single room rate will be reimbursed. Board members should pay personal expenses at checkout. If that is impossible, deductions for the charges should be made on the expense form.

  • Dewatering 4.7.1 Where a part of a site is affected by surface water following a period of rain, thus rendering some areas unsafe for productive work, consistent with the Employer’s obligations under the OH&S Act, all non- trades employees shall assist in ‘dewatering’ their own work site or area if it is so affected. Such work to be paid at single time rates. Productive work will continue in areas not so affected.

  • ROAD TOLERANCES Purchaser shall perform road work within the tolerances listed below. The tolerance class for each road is listed on the TYPICAL SECTION SHEET. Tolerance Class A B C Road and Subgrade Width (feet) +1.5 +1.5 +2.0 Subgrade Elevation (feet +/-) 0.5 1.0 2.0 Centerline alignment (feet lt./rt.) 1.0 1.5 3.0 1-6 ORDER OF PRECEDENCE Any conflict or inconsistency in the road plan will be resolved by giving the documents precedence in the following order:

  • Outdoor Lighting 3.8.1 Lighting shall be directed to driveways, parking areas, loading area, building entrances and walkways and shall be arranged so as to divert the light away from streets, adjacent lots and buildings.

  • Debriefing If a post-award debriefing is given to requesting offerors, the Government shall disclose the following information, if applicable:

Time is Money Join Law Insider Premium to draft better contracts faster.