Validation To validate the notice requirements outlined in Section 5.3, the Assuming Institution shall provide the Receiver (i) an Affidavit of Publication to meet the publication requirements outlined in Section 5.3(a) and (ii) the Assuming Institution will prepare an Affidavit of Mailing in a form substantially similar to Exhibit 2.3B after mailing the seven (7) day Notice to Depositors as required under Section 5.3(b).
Formation and Composition Within [ * ] after the Signing Date, the Parties shall establish a Joint Development Committee that shall oversee the Development and Manufacture (for Development) of Collaboration Products in Field in the Territory in accordance with the Development Plans for such Collaboration Products and to coordinate the Development and related Manufacturing activities of the Parties with respect to such Collaboration Products. Each Party shall initially appoint three (3) representatives to the JDC, each of whom will be an officer or employee of such Party and will have knowledge and expertise in the Development or Manufacture of products similar to the Collaboration Products and sufficient seniority within the applicable Party to make decisions arising within the scope of the JDC’s responsibilities. The JDC may change its size from time to time by mutual consent of its members. Each Party may replace its JDC representatives at any time upon written notice to the other Party. The JDC may invite non-members (including consultants and advisors of a Party who are under an obligation of confidentiality consistent with this Agreement) to participate in the discussions and meetings of the JDC, provided that such participants shall have no voting authority at the JDC. The JDC shall have a chairperson. Each Party shall have the right, on an alternating Calendar Year basis, to select from among its JDC representatives a representative to serve as the chairperson of the JDC during such Calendar Year. Such Party shall have the right during such Calendar Year to replace the chairperson of the JDC with one of its other JDC representatives. The initial chairperson shall be designated by [ * ]. The role of the chairperson shall be to convene and preside at meetings of the JDC, to prepare agendas (with due input from the other Party’s representatives), circulate agendas and to ensure the preparation of meeting minutes, but the chairperson shall have no additional powers or rights beyond those held by the other JDC representatives.
Inspection and Testing 7.5.1 Meters, data acquisition, and related protection equipment at Generator's Interconnection Point shall be tested at least biennially by Generator in accordance with the provisions for meter testing as established in American National Standard Institute Code for Electricity Metering (ANSI) Standard C12.16 for Solid State Electricity Meters, as the same may be updated from time to time. Representatives of each Party shall be afforded an opportunity to witness such tests.
Manufacture (a) Manufacturer shall only manufacture the specific number of Products as requested by Company and at no time shall manufacture excess goods or overruns. Manufacturer shall not sell any Products bearing the Trademarks to any third parties without the express written consent of Company.
Manufacturing Intrexon shall have the option and, in the event it so elects, shall use Diligent Efforts, to perform any manufacturing activities in connection with the Aquaculture Program that relate to the Intrexon Materials, including through the use of a suitable Third Party contract manufacturer. To the extent that Intrexon so elects, Intrexon may request that AquaBounty and Intrexon establish and execute a separate manufacturing and supply agreement, which agreement will establish and govern the production, quality assurance, and regulatory activities associated with manufacture of Intrexon Materials. Except as provided in Section 4.1, any manufacturing undertaken by Intrexon pursuant to the preceding sentence shall be performed in exchange for cash payments equal to Intrexon’s Fully Loaded Cost in connection with such manufacturing, on terms to be negotiated by the Parties in good faith. In the event that Intrexon does not manufacture Intrexon Materials or bulk quantities of other components of AquaBounty Products, then Intrexon shall provide to AquaBounty or a contract manufacturer selected by AquaBounty and approved by Intrexon (such approval not to be unreasonably withheld) all Information Controlled by Intrexon that is (a) related to the manufacturing of such Intrexon Materials or bulk qualities of other components of AquaBounty Products for use in the Field and (b) reasonably necessary to enable AquaBounty or such contract manufacturer (as appropriate) for the sole purpose of manufacturing such Intrexon Materials or bulk quantities of other components of AquaBounty Products. The costs and expenses incurred by Intrexon in carrying out such transfer shall be borne by Intrexon. Any manufacturing Information transferred hereunder to AquaBounty or its contract manufacturer shall not be further transferred to any Third Party, including any Product Sublicensee, or any AquaBounty Affiliate without the prior written consent of Intrexon; provided, however, that Intrexon shall not unreasonably withhold such consent if necessary to permit AquaBounty to switch manufacturers.
Manufacturing Technology Transfer With respect to each Technology Transfer Product, upon AbbVie’s written request after the Inclusion Date for the Included Target to which such Technology Transfer Product is Directed, Morphic shall effect a full transfer to AbbVie or its designee (which designee may be an Affiliate or a Third Party manufacturer) of all Morphic Know-How and Joint Know-How relating to the then-current process for the Manufacture of such Technology Transfer Product (the “Manufacturing Process”) and to implement the Manufacturing Process at facilities designated by AbbVie (such transfer and implementation, as more fully described in this Section 5.3, the “Manufacturing Technology Transfer”). To assist with the Manufacturing Technology Transfer, Morphic will make its personnel reasonably available to AbbVie during normal business hours for up to [***] FTE hours with respect to each Included Target (in each case, free of charge to AbbVie) to transfer and implement the Manufacturing Process under this Section 5.3. Thereafter, if requested by AbbVie, Morphic shall continue to perform such obligations; provided, that AbbVie will reimburse Morphic for its full-time equivalent (FTE) costs (for clarity, in excess of [***] FTE hours) and any reasonable and verifiable out-of-pocket costs incurred in providing such assistance. CERTAIN CONFIDENTIAL INFORMATION CONTAINED IN THIS DOCUMENT, MARKED BY [***], HAS BEEN OMITTED BECAUSE IT IS NOT MATERIAL AND WOULD LIKELY CAUSE COMPETITIVE HARM TO THE COMPANY IF PUBLICLY DISCLOSED.
Traceability Distributor agrees to maintain access to records allowing Micrus the ability to determine all customers who were shipped specific product lots. Product Identification and traceability requirements are defined in ISO 9001 : 1994 (E) requirement 4.8 as : “...the supplier shall maintain documented procedures for identifying the product from production, delivery and installation.” Traceability in ISO 8402 Vocabulary is defined as : “ability to trace the distribution and location of the product after delivery”.
Commercialization Intrexon shall have the right to develop and Commercialize the Reverted Products itself or with one or more Third Parties, and shall have the right, without obligation to Fibrocell, to take any such actions in connection with such activities as Intrexon (or its designee), at its discretion, deems appropriate.
Investigation and Prevention Transfer Agent shall reasonably assist Fund in investigating of any such unauthorized access and shall use commercially reasonable efforts to:
Development of Products (a) During the term of this Agreement, ViewRay may from time to time seek services from PEKO with respect to the development of certain Products that can be incorporated into the ViewRay Renaissance™ MRI-guided radiation therapy system. For each Program to be undertaken by PEKO pursuant to this Agreement, the parties will prepare a “Work Statement” and agree to said “Work Statement” in substantially the form attached as Attachment 1. Each Work Statement will describe: (i) the (i) services that PEKO will be responsible for providing to ViewRay and the deliverables that PEKO will be responsible for delivering to ViewRay (“Deliverable(s)”), (ii) delivery schedule for the Deliverables, (iii) pricing terms, (iv) work plan for the Program, and (v) ViewRay’s responsibilities in connection with the Program. Each Work Statement will be prepared based upon the requirements and information provided to PEKO by ViewRay. A separate Work Statement will be required for each Program; and each Work Statement will become subject to this Agreement only when mutually agreed and signed by ViewRay and PEKO.
