Simulation of CO2 Injection Using SENSOR Sample Clauses

Simulation of CO2 Injection Using SENSOR. Simulations of CO2 injection into the five-spot well pattern chosen for the first test were performed using the SENSOR (System for Efficient Numerical Simulation of Oil Recovery) reservoir simulator from Coats Engineering, Inc. (xxxx://xxx.xxxxxxxxxxxxxxxx.xxx/). The construction of the model, assumptions, and properties of the reservoir used to describe the five-spot test well pattern were as follows. Quarter five-spot Area = 800 ft by 800 ft Average thickness = 20 ft 10 layers, using a 10 by 10 by 10 grid (cell block size of 2 x 80 x 80 ft) Injector and producer in opposite corners No impediment to vertical flow Different layers have different permeabilities, but permeability is uniform within each layer Porosity = 0.154 Initial average water saturation = 0.6 Irreducible water saturation = 0.21 "Irreducible" oil saturation = 0.25 Capillary pressure neglected Reservoir temperature = 210 oF (results are not very sensitive to temperature) Viscosity of water at 5000 psi = 0.4 cP Injection pressure of 7500 psia and producing pressure of 3000 psia SENSOR default productivity indices for each well No allowance for CO2 dissolution in water No interaction of CO2 with the formation The programs used to calculate oil, water, and CO2 properties are listed in Appendix D.
Sample 1
AutoNDA by SimpleDocs

Related to Simulation of CO2 Injection Using SENSOR

  • Completion of Concrete Pours and Emergency Work 24.14.1 Except as provided in this sub-clause an employee shall not work or be required to work in the rain.

  • Prohibition Against Selecting and Installing Products Containing Hazardous Materials The Contractor shall not select, install or otherwise incorporate any products or materials containing Hazardous Materials within the boundaries of the Site. Should the Contractor or any Subcontractors have knowledge that, or believe that, an item, component, material, substance, or accessory within a product or assembly selected by the Contractor or any Subcontractor may contain Hazardous Materials it is the Contractor’s responsibility to secure a written certification from the manufacturer of any suspected material which identifies the specific Hazardous Material(s) contained, together with the Material Safety Data Sheets (MSDS) for such materials which shall be submitted to the Owner and Design Professional.

  • GARBAGE DISPOSAL, RECYCLING, AND BIODEGRADABLE MATERIALS A. Concessionaire shall be responsible for maintaining the cleanliness of the Concession Premises. Concessionaire shall ensure placement of all garbage and trash generated by the Concession Operation in designated containers and that said containers are emptied daily, or as more frequently required by Department, at a location within the Area designated by Department. Disposal costs from this latter location shall be borne by Department. Concessionaire shall provide such additional trash containers as may be required to keep the immediate Concession Premises clean at all times. The type of trash containers provided by Concessionaire shall be approved by Department prior to use.

  • LIMITATIONS ON REVERSE ENGINEERING, DECOMPILATION AND DISASSEMBLY You may not reverse engineer, decompile, or disassemble the Software, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

  • USE OF TBS ACCESS CODE (a) An Account Holder may operate the TBS in relation to his Account by using his TBS Access Code.

  • Musculoskeletal Injury Prevention and Control (a) The Hospital in consultation with the Joint Health and Safety Committee (JHSC) shall develop, establish and put into effect, musculoskeletal prevention and control measures, procedures, practices and training for the health and safety of employees.

  • Additional Acceptable Uses of Student Data Contractor is prohibited from using Student Data for any secondary use not described in this agreement except:

  • Inspection and Rejection of Nonconforming Goods (a) Buyer shall inspect the goods within five days of receipt (“Inspection Period”). Xxxxx will be deemed to have accepted the goods unless it notifies Seller in writing of any Nonconforming Goods during the Inspection Period and furnishes documentation reasonably required by Seller. “

  • Substance Use Disorder counseling shall be provided by a QCC, or Chemical Dependency Counselor Intern. Substance use disorder education and life skills training shall be provided by counselors or individuals who have been trained in the education. All counselor interns shall work under the direct supervision of a QCC.

  • Emergency Action on Imports of Particular Products Where any product is being imported in such increased quantities and under such conditions as to cause, or threaten to cause:

Time is Money Join Law Insider Premium to draft better contracts faster.