Common use of Slash Treatment Methods Clause in Contracts

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A > feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A> inches or larger in large end d.o.b. and < N/A> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Area Map and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A> inches or smaller in large end d.o.b. and < N/A> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A > with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/A

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A <> feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A<> inches or larger in large end d.o.b. and < N/A<> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Area Map and Sale Name: White Aspen Page: 160a designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A<> inches or smaller in large end d.o.b. and < N/A<> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A <> with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit EndUnit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Sale Name: White Aspen Page: 160b Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit EndUnit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit EndUnit d.o.b. (in) Length (feet) N/A)

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A <> feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A<> inches or larger in large end d.o.b. and < N/A<> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Contract Area Map and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 _ inches of the ground as shown on Sale Contract Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A<> inches or smaller in large end d.o.b. and < N/A<> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Contract Area Map with boundaries posted on the ground are < N/A <> with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by PurchaserContractor. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Contract Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by PurchaserContractor’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Unit Large End Unit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/A)

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A > feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A10> inches or larger in large end d.o.b. and < N/A10> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Area Map and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A> inches or smaller in large end d.o.b. and < N/A> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A > with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A 3,4,7 and 3 10 13 YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/A

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A > feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A> A inches or larger in large end d.o.b. and < N/A> A feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> N/A inches in large end d.o.b. and <10> N/A feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Area Map and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Sale Name: Transiton Page 169 Contract 2400-6, (6/06) SPECIFICATIONS PURSUANT TO C6.7# - SLASH TREATMENT (8/2006) CONTINUED Stack “Stacking” small material Logging Slash < N/A> A inches or smaller in large end d.o.b. and < N/A> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A > with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/A.

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 Specifications: Slash Throwback Cutting Units ALL Purchaser shall move all logging slash 3 inches diameter or larger at the large end created outside bark (d.o.b.)of the cutting unit boundary by Purchaser’s operations to locations at least 1 feet within the boundaries of the cutting units. Landing Cleanup Cutting Units ALL A landing is considered a place where any logs or products are gathered for processing and/or loading . Unless otherwise agreed, not to be otherwise treated, all slash accumulated at landings shall be bucked into lengths not to exceed 6 feet, unless agreed otherwisepiled. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. Piles shall be bucked into lengths not reasonably compact and free of soil to exceed < N/A > feet and left in placefacilitate burning. Logging Slash 4 inches and smaller in large end d.o.b. Piles shall be hand Piled within Required Disposal Strip for Forest Service disposalof a size and location which will not impair road use or result in damage to residual timber. Xxxx "Burying" Logging Slash shall The piling of landings will be buried where done by a grapple-type loader, excavator or as otherwise agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A> inches or larger in large end d.o.b. and < N/A> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long Cutting Units ALL Piles shall be hand Piled for disposal by Forest Servicelocated at least 30 feet from residual timber. Remove "Removing" Logging Slash Piles shall be moved or hauled range from 10 to locations shown on Sale Area Map N/A feet in diameter and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered 6 to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual treesN/A feet in height. All scattered logs objects which extend more than 6 feet in any direction from the pile profile will be cut off and returned to the pile. Fell Damaged Residual Cutting Units ALL Purchaser shall fell all species over 4 feet in height not meeting minimum diameter specifications for Included Timber and damaged beyond recovery by Purchaser's Operations. Such trees shall be limbed, placed away and stems bucked into lengths shorter than 8 feet. Stumps shall not exceed 6 inches in height from trees ground surface as measured on the uphill side and positioned so they shall be cut flat. Trees shall be completely severed from the xxxxx leaving no live limbs on the xxxxx. Tops, stems and limbs will not rollextend over 18 inches in height above the ground. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A> inches or smaller in large end d.o.b. and < N/A> feet or more in length Whole Tree Yarding Cutting Units ALL Whole trees shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A > with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, skidded or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum landings. Purchaser shall leave tops and limbs of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded felled trees attached to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/AIncluded Timber.

Slash Treatment Methods. Symbol Method Definition Buck-L “Bucking Large Logging Slash” Tops and limbs over 4 inches diameter outside bark (d.o.b.), not to be otherwise treated, shall be bucked into lengths not to exceed 6 feet, unless agreed otherwise. Buck-P "Bucking and Piling" Logging Slash smaller than < N/A > inches and larger than 4 inches in large end d.o.b. shall be bucked into lengths not to exceed < N/A > feet and left in place. Logging Slash 4 inches and smaller in large end d.o.b. shall be hand Piled within Required Disposal Strip for Forest Service disposal. Xxxx "Burying" Logging Slash shall be buried where agreed in borrow areas, pits, trenches, or other locations reasonably near the area of origin. Logging Slash shall be matted down in layers and shall be covered with at least 2 feet of rock and soil so that the final surface is sloped to drain and relatively smooth. Chip "Chipping" Chippable Logging Slash up to 4 inches in d.o.b. shall be processed through a chipping machine. Chips shall be scattered to a loose depth not exceeding 6 inches. Deck "Decking" large material Logging Slash < N/A> inches or larger in large end d.o.b. and < N/A> feet or more in length shall be Decked for disposal by Forest Service by piling pieces parallel to each other. Mach "Machine Piling" Concentrations of Logging Slash, excluding scattered individual pieces, shall be Machine Piled by tractor equipped with brush rake for disposal by Forest Service. Pile "Piling" small material Logging Slash smaller than <6> inches in large end d.o.b. and <10> feet long shall be hand Piled for disposal by Forest Service. Remove "Removing" Logging Slash shall be moved or hauled to locations shown on Sale Area Map and designated on the ground where it shall be piled for disposal by Forest Service. Scat 18" Scat 30" "Scattering" Logging Slash shall be scattered to reduce slash concentrations with slash being generally left within 18 or 30 inches of the ground as shown on Sale Area Map. Logging Slash shall be scattered into openings away from and without unnecessary damage to residual trees. All scattered logs shall be limbed, placed away from trees and positioned so they will not roll. When Scattering is specified, another method may be used by agreement. Stack “Stacking” small material Logging Slash < N/A> inches or smaller in large end d.o.b. and < N/A> feet or more in length shall be stacked for disposal by Forest Service by piling pieces parallel to each other. SAMPLE View “Visible Slash Treatment” Designated on Sale Area Map with boundaries posted on the ground are < N/A > with distance limitations for visible slash treatment. Within such units and the area of visible Logging Slash adjacent thereto, Logging Slash shall be treated by Purchaser. Primary treatment shall be by Removing, Burying, Chipping, Piling, Machine Piling, or a combination of these means unless a method is specified or prohibited on Sale Area Map. Logging Slash not readily treated by the selected or specified method shall be removed to designated areas or treated as agreed. YUMD “Yarding Unutilized Material-Decking” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be Yarded to landings and Decked. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUME “Yarding Unutilized Material-Exterior Boundary” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized material shall be yarded to locations a minimum of 50 feet slope distance within the exterior boundaries of such units and positioned so the yarded material will not roll. Large End Unit d.o.b. (in) Length (feet) N/A YUML “Yarding Unutilized Material-Landing” All unutilized material developed by Purchaser’s Operations shall be treated by the d.o.b. and length specifications as shown in the unit specification table. All unutilized shall be yarded to locations within 100 feet slope distance of landing. Where this is impractical, or other reasons, other locations shall be agreed upon. Large End Unit d.o.b. (in) Length (feet) N/A YUMR “Yarding Unutilized Material-Removal” All unutilized material developed by Purchaser’s Operations shall be treated by the bythe d.o.b. and length specifications as SAMPLE shown in the unit specification table. All unutilized shall be removed to locations shown on Sale Area Map and designated on the ground, or other agreed locations, and Decked. Large End Unit d.o.b. (in) Length (feet) N/A